pottery barn kids REESE CRIB User manual


Date:6‐Feb‐15www.potterybarnkids.com  Page1of12
Rev:  





pottery barn kids



























REESE CRIB








Date:6‐Feb‐15www.potterybarnkids.com  Page2of12
Rev:  


WARNING
Do not use this crib if you cannot exactly follow the accompanying instructions.
Do not use this crib for a child who can climb out of it or who is taller than 89 cm.
Do not place in or near this crib any cord, strap or similar item that could become
wrapped around a child’s neck.
Do not place this crib near a window or a patio door where a child could reach the cord of a
blind or curtain and be strangled.
Ensure that the crib is safe by checking regularly that every part is properly and securely in
place before placing the child in it. Do not use it if any parts are loose or missing or if there
are any signs of damage. Do not substitute parts. Contact the Pottery Barn Kids if
replacement parts or additional instructions are needed.
Use a crib mattress that is no thicker than 15 cm and is of such a size that, when it is pushed
firmly against any side of the crib, it does not leave a gap of more than 3 cm between the
mattress and any part of the sides of the crib.
Children can suffocate on soft bedding. Do not place pillows, comforters or soft mattresses in
this crib.
04-000052-8
WARNING: Failure to follow these warnings and assembly instructions
could result in serious injury or death.
Read all instructions before assembling crib. KEEP INSTRUCTIONS FOR FUTURE USE.
Never use plastic shipping bags or other plastic film as mattress covers because they can
cause suffocation.
Infants can suffocate in gaps between the crib sides and a mattress that is too small.
Never place additional padding under an infant.
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed on their
backs to sleep, unless otherwise advised by your physician.
STRANGULATION HAZARD: Strings can cause strangulation! Do not place items with a
string around a child’s neck, such as hood strings or pacifier cords. Do not suspend strings
over a crib or attach strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the body or
clothing on loose fasteners.
DO NOT place crib near window where cords from blinds or drapes may strangle a child.
FALL HAZARD: When child is able to pull to a standing position, set mattress to lowest
position and remove bumper pads, large toys and other objects that could serve as steps for
climbing out.
Stop using crib when child begins to climb out or reaches the height of 35 in. (89cm)
Check this product for damaged hardware, loose joints, loose bolts or other fasteners,
missing parts or sharp edges before and after assembly and frequently during use. Securely
tighten loose bolts and other fasteners. DO NOT use crib if any parts are missing, damaged
or broken. Contact Pottery Barn Kids for replacement parts and instructional literature if
needed. DO NOT substitute parts.
DO NOT use a water mattress with this crib.
Replace teething rail if damaged, cracked, or loose. NOTE: This is only for cribs with teething
rails.


Date:6‐Feb‐15www.potterybarnkids.com  Page3of12
Rev:  


If refinishing, use a non-toxic finish specified for children’s products.
Do not remove the metal brackets from the mattress base after installation.
NOTE: This is only for cribs supplied with a wooden mattress base.
Follow warnings on all products in a crib. 04-000056-7
CAUTION: ANY MATTRESS USED
IN THIS CRIB MUST BE AT LEAST 27 ¼”
(69 CENTIMETERS) BY 51 5/8” (131
CENTIMETERS) WITH ATHICKNESS NOT
EXCEEDING 6” (15 CENTIMETERS)
THIS CRIB CONFORMS TO APPLICABLE REGULATIONS PROMULGATED BY THE
CONSUMER PRODUCT SAFETY COMMISSION.
04-000094-3
IMPORTANT SAFETY INSTRUCTIONS:
Please read all instructions carefully before assembling.
For your safety, assembly by two or more adults is recommended.
Keep instructions for future use.
Use only vendor supplied hardware to assemble. Using unauthorized hardware could
jeopardize the structural integrity of the item.
Do not remove warning labels from the cribs. Labels are permanent and not designed to be
removed
PRE-ASSEMBLY:
Remove all parts and hardware from the box and lay out on a clear carpeted or scratch-free
work surface, as this will avoid damaging parts during assembly. The shipping box provides
an ideal work surface.
Do not dispose of any packaging or contents of the shipping carton until assembly is
completed to avoid accidentally discarding small parts or hardware.
Use the parts and hardware lists below to identify and separate each of the pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the
assembly instructions.
The use of power tools to aid in assembly is not recommended. Power tools can damage
hardware and split wood.


Date:6‐Feb‐15www.potterybarnkids.com  Page4of12
Rev:  


Product labeling for Crib configuration with slatted crib ends. Crib is depicted upside down.
04‐000141
WarningLabel
04‐000141
WarningLabel
04-000141-1
Warning Label
Étiquette de Mise en Garde
04-000141-1
Warning Label
Étiquette de Mise en Garde


Date:6‐Feb‐15www.potterybarnkids.com  Page5of12
Rev:  


PARTS INCLUDED:
(A) CRIB END (2x)
(B) CRIB STATIONARY SIDE (2x)
(C) MATTRESS BASE (1x)
(D) LEG SUPPORT (2x)
(E) LEG (4x)
A
A
B
C
B
D
D
E
E
E
E


Date:6‐Feb‐15www.potterybarnkids.com  Page6of12
Rev:  


HARDWARE INCLUDED:
(F) Bolt M6x60mm - (4x) (G) Half Moon Washer - (4x)
(H) Bolt M6x45mm - (20x)
(I) Bolt M6x27mm - (4x) (J) Bolt M6x10mm - (8x) (K) Allen Key with Ball Tip - (1x)
(L) Left Bracket - (2x) (M) Right Bracket - (2x)


Date:6‐Feb‐15www.potterybarnkids.com  Page7of12
Rev:  


ASSEMBLY INSTRUCTION STEPS:
1. Attach (L&M) to (C). UseAllen Key (K) to tighten as shown below.
Note: Make sure the brackets (L&M) point outwards as shown below
(J) Bolt - 8x
(L) Left Bracket - 2x(M) Right Bracket - 2x
4x
C
M
J
K
J
L
L
J
J M


Date:6‐Feb‐15www.potterybarnkids.com  Page8of12
Rev:  


2. Assemble (B) to (A). Do not fully tighten bolts (F&H) at this time.
*Tip: See Image A on how to assemble half moon washer (G).
(H) Bolt M6x45mm - 2x
(F) Bolt M6x60mm - 2x(G) Half Moon
Washer - 2x
2x
B
A
A
G F K
2x
H
K
1.
2.
Image A
Arrowstickersidedown.
Arrowpointsinside


Date:6‐Feb‐15www.potterybarnkids.com  Page9of12
Rev:  


*Note: The mattress base (C) may be at the highest level (Level 2) when the child is
born. It must be at the lowest level (Level 1) before the child can stand up. Before
installing the mattress base (C), please ask the customer at which height they want it
installed (Illustration showing Mattress base install in the highest position).
3. After determining the desired height of the mattress base (C). With the help of an
adult, place the Mattress Base (C) into the crib by carefully not to scratch the finish.
Attach (C) to (A) as shown below. Do not fully tighten (I) at this time.
*Note: To change the position of the Mattress Base (C), remove bolts (I), line up the
Mattress Base (C) with the holes at the desired height (Level 1 or 2) and re-attach the
Mattress Base (C) with bolts (I).
(I) Bolt- M6x27mm - 4x
Installed in the highest position.
4x
C
A
A
I
K
Level 2
Level 1
C
4x


Date:6‐Feb‐15www.potterybarnkids.com  Page10of12
Rev:  


4. Attach (B) to (A) as shown below.


(H) Bolt- M6x45mm - 2x
A
A
B
2x
K
H
Arrowstickersidedown.
Arrowpointsinside


Date:6‐Feb‐15www.potterybarnkids.com  Page11of12
Rev:  


5. Carefully turn the crib lying down on its side. Attach (B) to (A) using Bolts (F) and Half Moon
Washer (G) as shown below.
*Tip: See Image A at step 2 on how to assemble half moon washer (G).
6. Attach (E) to (D) as shown below.
*Note: Make sure the Leg point outwards.
(H) Bolt M6x45mm - 8x
E
E
D
K
H
4x
A
2x
B
G FK
(F) Bolt M6x60mm - 2x
(G) Half Moon Washer - 2x


Date:6‐Feb‐15www.potterybarnkids.com  Page12of12
Rev:  


Thank you for your purchase
stores | catalog | www.potterybarnkids.com
U.S.A 1.800.290.8181
7. Attach the LegAssembly to (B) as shown below.
*Note: Make sure the Leg point outwards.
8. Gently turn the Crib Upright. Check alignments and fully tighten all connections at this time.
9. Assembly is now complete.
10. Place the assembly instructions back into the envelope mounted on the mattress base for
future reference.
CARE INSTRUCTIONS:
Dust often using a clean, soft, dry, lint-free cloth.
Blot spills immediately, and wipe with a clean, damp cloth.
We do not recommend the use of chemical cleansers, abrasives, or furniture polish on our
lacquered finish.
If the crib is to be stored, store in cool dry place and carefully package all original hardware to
protect from loss or damage.
Check fasteners periodically for tightness. DO NOT over tighten, as this may cause distortion
or breakage.
Parents should ensure a safe environment for the child by checking the crib regularly that
every component is properly and securely in place, before placing the child in the product.
(H) Bolt M6x45mm - 8x
B
4xK
H
B