PotteryBarn Bedford Bookcase User manual

A
b
c
C
Bedford 3 x 3 Bookcase
Assembly Instructions
Pre-Assembly:
•Please read all instructions carefully before beginning assembly.
•For your safety and ease, assembly by two people is recommended.
•Use the parts and hardware lists to identify and separate each of the components included.
•Save all packing materials until assembly is complete to avoid the accidental discarding of
smaller parts or hardware.
Parts Included:
•(1) Bookcase (A)
•(6) Shelves (B)
Needed For Assembly:
•(1) 3x3 Bookcase (C) (sold separately)
Tools Required:
•Phillips Head Screwdriver (not included)
To Assemble:
1. Attach the metal wire (a) into the pre-drilled holes on the bookcase (A), repeat with the
other wires. (Fig. 1)
2. Align the slots on the shelves (B) with the metal wires (a) and push to attach. (Fig. 2)
3. If a second bookcase is to be stacked on top of the first bookcase, the four screws (c) on the
gliders underneath the second bookcase (C) need to be released. (Fig. 3)
4. Attach sponge tape (d) on top of the first bookcase (A) about 1 inch from the edge. With at
least two people, move the first bookcase to its final location and place the second bookcase
(C) on top of the first bookcase (A). (Fig. 4)
5. Align the pre-drilled holes on the back of both bookcases. Using the pre-drilled holes as a
guide, affix the mounting plates (b) to the back of both bookcases. Secure with the screws (c)
and tighten with a screwdriver. (Fig. 5)
6. Install anti-tip kit (see separate instructions).
7. Assembly is complete.
Care Instructions:
•Wipe using a clean, soft, dry cloth.
•To protect the finish, avoid the use of all chemicals and harsh abrasives.
•A light application of furniture polish or wax may be used to restore the wood’s finish.
Hardware Enclosed:
•(12) Metal Wires (a)
•(2) Mounting Plates (b)
•(4) Phillips Head Screws (c)
•(8) Sponge tape (d)
Fig. 1
Fig. 2
Fig. 3
Fig. 4
Fig. 5
A
a
B
a
d
C
A
C

thank you for your purchase
stores | catalog | www.potterybarn.com

a
c
B
B
A
C
A
b
A
B
ca
b
align
E
Bedford Project Table
Assembly Instructions
Pre-Assembly:
•Please read all instructions carefully before beginning assembly.
•For your safety and ease, assembly by two people is recommended.
•Use the parts and hardware lists to identify and separate each of the components included.
•Save all packing materials until assembly is complete to avoid the accidental discarding of
smaller parts or hardware.
•Note: Bedford 3 x 3 Bookcases (sold separately) are needed to support the Project Table.
Parts Enclosed:
•(1) Tabletop (A)
•(2) Aprons (B)
Needed For Assembly:
•(2) Bookcase (C)
•(12) Shelves (D)
•(16) Sponge Tape (E)
Tools Required:
•Phillips Head Screwdriver (not included)
To Assemble:
1. Lay the tabletop (A) upside down on a carpeted or scratch-free work surface. Align the pre-
drilled holes on the apron (B) with the pre-dilled holes on the tabletop (A). Secure with the
Allen Bolts (a) using the Allen key (c). (Fig. 1)
2. Set the two bookcases (C) upright on the floor with open compartments facing outward. (Fig. 2)
3. Attach the sponge tape (E) on top of the bookcases about 1 inch from the edge. Please mark the
top of bookcase where there are holes underneath the bookcase top. Align the pre-drilled holes
underneath the bookcase tops (C) with the pre-drilled holes underneath the tabletop (A).
Secure together with the pan head screws (b) using a Phillips screwdriver. (Fig. 2)
4. Align the slots on the shelves (D) with the pre-inserted metal wires in the bookcase and push
shelves in to attach. Repeat with the other bookcase.
5. Assembly is complete.
Care Instructions:
•Wipe using a clean, soft, dry cloth.
•To protect the finish, avoid the use of all chemicals and harsh abrasives.
•A light application of furniture polish or wax may be used to restore the wood’s finish.
thank you for your purchase
Hardware Enclosed:
•(8) Allen Bolt M6 x 40mm (a)
•(6) Pan Head Screw 8 x 1 1/2” (b)
•(1) Allen Key (c)
Fig. 1
Fig. 2
Fig. 3
C
D

stores | catalog | www.potterybarn.com