PotteryBarn HOTEL DOUBLE DOOR CABINET User manual

HOTEL DOUBLE DOOR CABINET WITH CUBBIES
Assembly Instructions
Note:
• This hanging system is meant for drywall/stud mounting only.
• If walls are concrete, brick or plaster, please consult your local hardware store for assistance.
• Professional Installation Recommended – Otherwise, for safety and ease of mounting, installation by two
people is recommended.
• The maximum individual shelf weight capacity is 20 pounds and the total product weight capacity of
100 pounds.
Hardware Included:
• (2) Shelves
• (8) Shelf Brackets
• (1) 18” Wall Bracket
• (2) Toggle Screws
• (2) Toggles
(Toggles/Screws are meant for drywall only)
• (1) Wood Screw
• (1) Small Anchor
• (1) Small Screw
• (1) Plastic Plug
• Metal Knob and Screw
Tools Needed:
• Stud Finder
• #2 Phillips Screwdriver
• Pencil
Pre-Assembly:
• Remove all parts and hardware from the box and lay out on a clear workspace, along with any plastic
protective packaging. Do not dispose of any contents until assembly is complete to avoid accidentally
discarding small parts or hardware.
• Use the parts and hardware lists above to identify and separate each of the pieces included.
• The illustrations provided allow for easier assembly when used in conjunction with the assembly instructions.
INSTALLATION SUMMARY:
FIND WALL STUDS
MOUNT WALL BRACKET TO THE WALL
HANG THE PRODUCT ONTO THE MOUNTED WALL BRACKET
FIND WALL STUDS:
1. Determine the desired placement on the wall for the product. Within that range, locate a stud using a stud
finder and make a small mark on the wall with a pencil at that location.
2. It is best to mount the bracket to at least (1) stud. Using Figure 1, determine which hole on the wall bracket
will be over the stud, this hole will take a wood screw alone.
Note: it is possible the bracket may align over two wall studs.
MOUNT WALL BRACKET TO THE WALL
1. Insert the supplied bubble level into the channel of the wall bracket. Position the wall bracket on the wall
and adjust so that the bracket is level and a pre-drilled hole of the bracket aligns with a stud. Then, use a
felt-tipped pen to mark the wall through appropriate pre-drilled holes of the bracket to indicate the locations
of the drywall toggles. Also make sure to mark the bracket itself at each selected pre-drilled hole using the
pen. (Please refer to Figure 1 to determine the location of the hardware.) The locations of the drywall
toggles will depend on how the stud aligns with the bracket. The user should make sure that the stud and
the toggles are evenly spaced along the length of the bracket and that the ends of the bracket should be
secured using either a stud-mounted screw or a drywall toggle.
2. Remove the wall mount bracket and set aside.
3. Using a manual screwdriver, drive a toggle into the drywall at each mark. To install these toggles into the
wall, simply rotate them at the marked location as if they were a large screw, applying smooth even force.
DO NOT HIT THEM WITH A HAMMER AND DO NOT USE A POWER DRILL TO ROTATE THEM. These
toggles are designed to bore themselves into the wall. Continue rotating until the toggle head advances
flush with the wall surface.

4. Once the toggles are installed into the wall at the marked locations, reposition the wall bracket so that the
marked holes of the bracket align with the toggles. Using the supplied toggle screw secure the bracket to
the installed toggles. Note: The toggle includes a nut portion that must be “set” into a locked position prior
to using the product. This is done automatically as you rotate the toggle screw into the toggle, but keep in
mind that the screw must be rotated quite a few times before the nut finally reaches this locked position.
The nut will create resistance when it reaches the locked position within the wall.
5. Once the wall bracket is attached to each toggle using the toggle screw, the bracket must be secured to the
stud located along the bracket. Use the supplied stud mount screw to secure the wall bracket to the stud
(note, a pre-drilled hole of the bracket should align with the stud location).
Figure 1
HANG THE PRODUCT ONTO THE MOUNTED WALL BRACKET
1. On the back of your product is an affixed product-mounting bracket.
2. With the help of another person, carefully position the product-mounting bracket slightly above and against
the wall mount bracket, insuring that the two brackets are aligned. Engage the two brackets.
3. With a pencil, mark on the wall through the location of the lower mounting point.
4. Remove the cabinet. Use the marked point as the insertion point for the small anchor. Place the #2
Phillips screwdriver into recess of the anchor. Slowly turn the anchor clockwise while applying pressure
until the flange just touches the wall.
5. Again, carefully position the product-mounting bracket slightly above and against the wall mount bracket,
insuring that the two brackets are aligned.
6. Press down firmly to engage the two brackets.
7. Insert the small screw through the pre-drilled hole inside the cabinet. Tighten against wall. Cover the
screw head with plastic plug.
SHELF INSTALLATION:
1. Insert shelf brackets into coordinating holes at desired level. Align the bottom slots of each shelf with the
corresponding holes. Push down to secure.

KNOB INSTALLATION:
1. Removal:
Hold the door knob. Using a screwdriver, unscrew the screw by turning in a counter-clockwise rotation.
2. Installation:
Hold the door knob at the pre-drilled hole. Using a screwdriver, attach the knob with the screw by turning in
a clockwise direction.
Care Instructions:
• Clean with a soft, dry cloth.
• To protect the finish, do not apply household cleaners or abrasives.
Thank you for your purchase
stores | catalog | www.potterybarn.com