Power Tec 71392 User manual

Owner’s Manual
Model No. 71392
Trim Router Table
You will need this manual for safety instructions, operating procedures, and warranty.
Put it and the original sales invoice in a safe, dry place for future reference.
Visit us on the web at powertecproducts.com
QUESTION...
1•847•780•6120
20-0331

PRODUCT
SPECIFICATIONS
Dimensions
Table Top ................................................. 11-1/2"x 15-1/2" x 3/4"
Bit Guard ............................................................................3" x 5"
Fence .................................................15-1/2" x 2-11/16" x 1-1/2"
TABLE OF CONTENTS
SAFETY RULES 1
ASSEMBLY 2
MAINTENANCE 4
General Maintenance
WARRANTY 5
SECTION PAGE
Unpacking
Assemble Fence, Dust Port and Table
Assembly the Trim Router Base
Installing Router in Table

SAFETY RULES 1
1
SAFETY RULES
WARNING
For your own safety, read all of the rules and precautions before
operating tool.
WARNING
Always follow proper operating procedures as defined in this
manual even if you are familiar with use of this trim router table
or any tool used with this trim router table. Remember that being
careless for even a fraction of a second can result in severe
personal injury.
Before using another tool with this product, always read,
understand and follow the instructions and safety warnings in
the owner’s manual for that tool. If you do not have the owner’s
manual, obtain one from the tool’s manufacturer before using it
with this product.
You must be familiar with the use of any tool or accessory
used with this trim router table. The supplier cannot be held
responsible for any accident, injury or damage incurred while
using this trim router table with any tool.
It is the purchaser of this product is responsible to ensure
that any person using this product reads and complies with all
instructions and safety precautions outlined in this manual prior
to use.
WARNING
Some dust created by operation of power tool contains
chemicals known to the State of California to cause cancer, birth
defects or other reproductive harm. To reduce your exposure
to these chemicals, work in a well ventilated area and work
with approved safety equipment. Always wear OSHA/NIOSH
approved, properly fitting face mask or respirator when using
such tools.
CAUTION
Do not modify or use this trim router table for any application
other than that for which it was designed.
FOLLOW ALL STANDARD SHOP SAFETY
PRECAUTIONS, INCLUDING:
• Keep children and visitors at a safe distance from work area.
• Keep work area clean. Cluttered work areas invite accidents.
Work area should be properly lit.
• Do not use power tools in dangerous environments. Do not
use power tools in damp or wet locations. Do not expose
power tools to rain.
• Wear proper apparel. Do not wear loose clothing, gloves,
neckties, rings, bracelets or other jewelry which may get
caught in moving parts of the tool.
• Wear protective hair covering to contain long hair.
• Wear safety shoes with non-slip soles.
• Wear safety glasses complying with United States ANSI
Z87.1. Everyday glasses have only impact resistant lenses.
They are NOT safety glasses.
• Wear face mask or dust mask if operation is dusty.
• Be alert and think clearly. Never operate power tools when
tired, intoxicated or when taking medications that cause
drowsiness.
• A guard or any other part that is damaged should be properly
repaired or replaced. Do not perform makeshift repairs.
• Use the right tool for your job. Do not force your tool to do a
job for which it was not designed.
• Use safety equipment such as featherboards, push sticks and
push blocks, etc., when appropriate.
• Maintain proper footing at all times and do not overreach.
WARNING
• This trim router table MUST be clamped securely to a
stationary support or attached to a cleat (using the pre-drilled
cleat mounting holes) and clamped securely to a stationary
support. Failure to properly secure the table could result in
serious injury and property damage.
• To avoid serious injury, turn off and unplug the router before
attaching the router base, changing accessories or adjusting
the cutter height/fence position.
CAUTION
Think safety! Safety is a combination of operator common sense
and alertness at all times when tool is being used.
WARNING
Do not use the trim router table until it is completely assembled
and you have read and understood this entire operating manual
and the operating manual of the tool being used with this trim
router table.
SAVE ALL WARNINGS AND INSTRUCTIONS
FOR FUTURE REFERENCE

2
ASSEMBLY
ASSEMBLY
2
UNPACKING
Refer to Figure 1
Check for shipping damage. Check immediately whether all
parts and accessories are included.
ITEM DESCRIPTION QTY
A Router table top 1
B Bit guard 1
CBit guard knobs 2
D Universal trim router base
(Powertec 71381)
1
ERouter dust port (Powertec 70152) 1
FRouter table fence 1
GFence lock knobs 2
HT-Bolts 5/16"-18 x 4" 2
IWashers 5/16" 2
JM4 x 10 mm pan head screws 2
KWashers 1/4" 2
LHex wrench 3 mm 1
MLeveling screws 1" (hex head) 3
N45 Degree elbow (2-1/2") 1
Figure 1
B
C
D
G
F
E
H
A
J
I
K
L
M
N
WARNING
Do not use the trim router table until it is completely assembled
and you have read and understood this entire operating manual
and the operating manual of the tool being used with this trim
router table.
ASSEMBLE FENCE, DUST PORT AND TABLE
Refer to Figure 2–6
1. From the underside of the fence, insert the two T-Bolts up
and through the holes on each end the fence. Place a 5/16"
washer on each T-Bolt and then thread on the fence lock
knobs. Do not tighten the knobs.
2. Attach the Powertec 70152 dust port to the back of the
fence using the pan head screws and 1/4" washers. Slide
the 45 degree elbow into the dust port.
NOTE: The elbow has a 2-1/2" OD opening and is designed
to work with 2-1/2" ID dust collection hoses.
Figure 2
T-Bolt
Fence Lock Knob
Fence
5/16"
Washer
Washers 1/4"
Pan Head Screws
M4 x 10 mm
Dust Port
45 Degree
Elbow
3. Optional mounting: The trim router table may be attached
to a longer board or cleat for clamping to a stationary work
surface. If using this method, add the cleat now. There are
pre-drilled cleat mounting holes at the rear of the trim router
table. Drive #8 screws through the three cleat mounting
holes and into the cleat. NOTE: The screw length should be
the thickness of the trim router table plus the cleat)
Figure 3
Cleat
Cleat Mounting Holes
4. Install the fence to the table. Make sure the T-Bolt heads
extend down far enough to fit into the fence adjustment slots
in the table. Insert the T-Bolt heads into the round access
holes in the tabletop, engage the heads in the stepped slots
on the underside of the table and slide the fence toward
the back.
NOTE: To adjust the fence, loosen the knobs, slide the
fence to the desired application and tighten knobs.

3
ASSEMBLY
Figure 4
T-Bolt Head
Fence Lock
Knob
Fence
Round
Access
Hole
Fence
Adjustment
Slot
WARNING
The trim router table MUST be clamped or attached directly to a
stationary work surface BEFORE operating the router. Figure 5
shows the trim router table with cleat clamped to a stationary
work surface.
5. Clamp or Attach the Table to Stationary Work Surface:
a. If the cleat was assembled earlier, clamp it to the edge
of a bench, table, piece of plywood or other stationary
work surface.
b. The table may be attached directly to a stationary
work surface. Drive #8 screws through the three cleat
mounting holes and into the stationary work surface.
IMPORTANT: The screw length will be determined
by the work surface thickness. The general rule is for
the screw to enter at least half the thickness of the
bottom material/work surface.
Figure 5
Clamp
Clamp
Cleat
Solid Work
Surface
6. Install the three leveling screws from the bottom into the
holes on the lip of the opening in the table. NOTE: These
screws are used to make the router base flush with the face
of the tabletop. These screws will also register the three
stopped holes in the underside of the trim router base to
keep it from shifting during use.
Figure 6
Leveling Screws
Leveling Screws
ASSEMBLY THE TRIM ROUTER BASE
WARNING
To reduce the risk of injury, turn router off and disconnect it from
power source before installing and removing accessories. An
accidental start-up can cause injury.
NOTE: This clear router plate provides better visibility and
when used with a PORTER-CABLE style guide bushing (sold
separately) it allows a bit to follow the path intended by a
template or jig.
NOTE: The trim router base can be left on the router, allowing
it to be taken from table routing to hand held routing without
switching baseplates.
1. Remove the existing router plate and all related hardware
from the router.
2. On the chart find the model and the corresponding letter for
your router.
3. Find the corresponding letters for your router in Figure 7.
NOTE: Some routers have more than one option.
4. Place the universal router plate onto the router and line up
the first letter with the appropriate hole and then rotate the
plate until all holes for the pattern line up. Install and tighten
the machine screws.
Figure 7
DeWALT* * PORTER-CABLE,
DeWALT and
Craftsman are
trademarks of The
Black & Decker
Corporation/ Bosch
is a trademark of the
Robert Bosch Tool
Corporation/ Makita is
a trademark of Makita
Corporation/ Ryobi
is a trademark of
RYOBI, LTD.
DWP611PK AFixed Base
BPlunge Base
Makita*
RT0701CX7 CPlunge Base
DFixed Base
Bosch*
GKF125CEN E
PR110 F
PR10E/PR20EVS F
Ryobi*
P601 G
PORTER-CABLE*
PCE6435 H

GENERAL MAINTENANCE
WARNING
When servicing, use only identical replacement parts. Use of
any other parts may create a hazard or cause product damage.
To ensure safety and reliability, all repairs should be performed
by a qualified service technician.
WARNING
Keep the trim router table dry, clean, and free from oil and
grease. Always use a clean cloth when cleaning. Never use
brake fluids, gasoline, petroleum based products or any
strong solvent to clean the trim router table. Chemicals can
damage, weaken or destroy plastic which may result in serious
personal injury.
MAINTENANCE
4
MAINTENANCE
4
INSTALLING ROUTER IN TABLE
1. Loosen the fence locking knobs and slide the fence back on
the tabletop to access the opening in the tabletop.
2. From the top of the table, lower the router with trim router
base into the opening, align the three stopped holes on the
underside of the router base with the three leveling screws.
Figure 8
Stopped holes in trim
router base aligned
with leveling screw
Stopped holes in trim
router base aligned
with leveling screw
Use a straight edge to verify the trim router base is flush with the
tabletop. If it is not flush, adjust the leveling screws until the
router base plate is flush with the tabletop. Make sure the
leveling screws are seated in the three stopped holes on the
underside of the router base to prevent the base from shifting
during use.
10
9
8
7
6
5
4
3
2
10
321 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 250
Figure 9
Hex
Wrench
included
4
ASSEMBLY
Trim Router Base
• Carnauba wax may be applied to the universal router plate to
reduce scratching and make it slide easier. If scratching does
occur, carefully polish with plastic polish until the scratches
are removed.
3. Attach the bit guard to the front of the fence using the bit
guard knobs.
NOTE: To adjust the bit guard, loosen the knobs, slide
the bit guard up and down to desired application and
tighten knobs.
4. Adjust the fence to the desired application and tighten the
locking knobs.
5. Attach the dust extraction hose to the dust port.
Figure 10
Bit Guard Bit Guard
Knobs
WARNING
The trim router table MUST be clamped in place or attached
directly to a solid mounting surface BEFORE operating the
router. Figure 5 shows the trim router table with cleat clamped
into place.

WARRANTY 5
WARRANTY
5
Thank you for investing in a POWERTEC power tool. This product has been designed and manufactured to meet high
quality standards and is guaranteed for domestic use against defects in workmanship or material for a period of 12
months from the date of purchase. This guarantee does not affect your statutory rights.
SOUTHERN TECHNOLOGIES LLC. BENCH TOP AND STATIONARY POWER TOOL
LIMITED 1 YEAR WARRANTY AND 30-DAY SATISFACTION GUARANTEE POLICY
POWERTEC products are designed and manufactured by Southern Technologies LLC. All warranty communications
should be directed to Southern Technologies LLC by calling 847-780-6120, 9 AM to 5 PM, Monday through Friday,
US Central Time.
30- DAY SATISFACTION GUARANTEE POLICY
During the rst 30 days after the date of purchase, if you are dissatised with the performance of this POWERTEC tool
for any reason, you may return the tool to the retailer from which it was purchased for a full refund or exchange. You
must present proof of purchase and return all original equipment packaged with the original product. The replacement
tool will be covered by the limited warranty for the balance of the one year warranty period.
LIMITED ONE YEAR WARRANTY
This warranty covers all defects in workmanship or materials in this POWERTEC tool for a one year period from the
date of purchase. This warranty is specic to this tool. Southern Technologies, LLC reserves the right to repair or
replace the defective tool, at its discretion.
HOW TO OBTAIN SERVICE
To obtain service for this POWERTEC tool you must return it, freight prepaid, to POWERTEC. You may call
847-780-6120 for more information. When requesting warranty service, you must present the proof of purchase
documentation, which includes a date of purchase. POWERTEC will either repair or replace any defective part, at
our option at no charge to you. The repaired or replacement unit will be covered by the same limited warranty for the
balance of one year warranty period.
WHAT IS NOT COVERED
This warranty applies to the original purchaser at retailer and may not be transferred.
This warranty does not cover consumable items such as saw blades, knives, belts, discs, cooling blocks and sleeves.
This warranty does not cover required service and part replacement resulting from normal wear and tear, including
accessory wear.
This warranty does not cover any malfunction, failure or defect resulting from:
1) misuse, abuse, neglect and mishandling not in accordance with the owner’s manual.
2) damage due to accidents, natural disasters, power outage, or power overload.
3) commercial or rental use.
4) alteration, modication or repair performed by persons not recommended by POWERTEC.
DISCLAIMER
To the extent permitted by applicable law, all implied warranties, including warranties of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE, are disclaimed. Any implied warranties, that cannot be disclaimed under
state law are limited to one year from the date of purchase. Southern Technologies LLC. is not responsible for direct,
indirect, incidental or consequential damages. Some states do not allow limitations on how long an implied warranty
lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations
may not apply to you. This warranty gives you specic legal rights, and you may also have other rights which vary from
state to state. Southern Technologies LLC., makes no warranties, representations, or promises as to the quality or
performance of its power tools other than those specically stated in this warranty.

Southern Technologies, LLC
Waukegan, IL 60087