Powercom Mini wrs7000dsi-5 User manual

USER MANUAL

PowerCom Mini

WRS7000DSI-5

Licensed software products are owned by PowerCom® and are protected by United States

Fleetwood Group, Inc. manufactures PowerCom Mini for Dynamic Services International Inc. on

OEM base. The relevant products are covered by U.S. and foreign patents, issued and pending.

Information in this publication supersedes that in all previously published material.

Specifications and pricing are subject to change without notice.

Printed in the U.S.A.

Dynamic Services International Inc.

www.powercomars.com

www.dsii.net

Tel: 212 997 2000

Email: PowerCom@dsii.net

PowerCom Mini is a registered trademark of Dynamic Services International Inc. Other

trademarks contained herein are the property of their respective holders.

Control Version

Date

1.0

April, 2013

Table of Contents

1.0 PowerCom Mini ...................................................................................1

1.1 Introduction ...............................................................................................................................1

1.2 Applications/Advantages ...........................................................................................................1

1.3 RF Communication.....................................................................................................................1

1.4 About PowerCom.......................................................................................................................1

1.5 Other PowerCom Products........................................................................................................1

2.0 Principles of Operation .........................................................................2

3.0 System Description and Setup ................................................................2

3.1 Room Layout ..........................................................................................................................2

3.2 Placement of the PowerCom Mini System................................................................................2

4.0 How to Use the PowerCom Mini (WRS7000-DSI-5)...........................................3

4.1 Powering On ..............................................................................................................................3

4.2 Voting.........................................................................................................................................3

4.3 Key Lockout................................................................................................................................3

5.0 Static mode keypad..............................................................................3

6.0 Keypad Settings Retrieval ......................................................................4

6.1 Keypad locally ............................................................................................................................4

6.2 Changing Keypad and Channel Number ....................................................................................4

7.0 Keypad Battery Replacement ..................................................................4

8.0 Software...........................................................................................4

9.0 Accessories........................................................................................4

10.0 Limited Product Warranty.....................................................................4

11.0 FCC, IC, and EU Compliance Information .................................................5

12.0 Standards and Guidelines .....................................................................5

13.0 FCC/IC Compliance.............................................................................6

14.0 EU Compliance ..................................................................................6

15.0 Technical Specifications.......................................................................7

16.0 Troubleshooting Procedures ..................................................................8

17.0 Index .............................................................................................9

1.0 PowerCom Mini

1.1 Introduction

This product consists of wireless (RF) keypads

and a Base Station. The system is generally used

to record answers to multiple choice questions

as part of a classroom presentation, decision-

making session, focus group, or

videoconference. It offers methods for

collecting and immediately reporting group

response data.

PowerCom Mini is a cordless handheld

response system that provides numeric

data interaction for meeting or

learning environments. Keypad

responses are transmitted to the Base

Station, which processes and delivers

the information to the attached

computer.

Application software operates the Base

Station and controls its associated

Keypads. While the system’s hardware

may offer powerful features, application

software is the essential ingredient in applying

the technology to generate useful results.

1.2 Applications/Advantages

Many meeting and learning venues require a

mechanism for audience interaction. Moreover,

many seek a method of automating surveys and

grading activities. PowerCom Mini meets the

need for such an interactive tool, bringing

everyone together and instantly allowing

measurement of interest, understanding, and

involvement.

Audience members can participate from

their seat and personally indicate their

opinions, ideas, and knowledge.

Results of the interaction are immediately

available, and their display offers presenters

a valuable insight into the opinion and

comprehension level of audience members.

System setup typically involves handing a

Keypad to every participant and connecting

the Base Station to a computer. No Keypad

wires or cabling need be installed prior to

use. This allows fast, reliable, safe, and

attractive installation.

1.3 RF Communication

The Keypads communicate with the Base

Station using wireless Radio Frequency

(RF) technologies. The patented

proprietary design has been rigorously

tested and optimized for reliability and

collection speed.

1.4 About PowerCom

PowerCom® is an Audience Response Software

division of Dynamic Services International, Inc.

(DSI). DSI was founded in 1988 with a mission

to help businesses of all sizes to build stronger

communications with their customers,

employees and business partners. With a focus

on building strong autonomous communication

channels, DSI is able to help companies collect

and exchangevaluable business information.

Our technology solutions focus around

generating fewer errors, fewer returned

documents, and fewer lost documents, as well

as a much faster response time. As a premier

provider of Information Technology and

Business Processes, DSI s a trusted technology

partner for many commercial and government clients.

1.5 Other PowerCom Products

PowerCom® has developed its software in 9

major languages and offices around the world;

we are committed to bringing the highest level

of products and customer service to users in

every country! We provide Audience Response

System distribution, rental service, and full

support to PowerCom®customers all over the

world! With Interactive PowerPoint Presentation

software in nine languages, PowerCom®

provides the highest quality audience response

systems for international businesses.

Recognized by Microsoft as a Partner, PowerCom

is the most respected Interactive Presentation

Software developer in the business. We

guarantee that we provide the lowest priced

ARS packages and rental service in the world!

For more information on these products or our

customization capability, please visit our

website at www.powercomars.com.

2.0 Principles of Operation

PowerCom Mini uses the latest in 2.4 GHz

wireless technology to turn any meeting into a

dynamic interactive experience for each

participant without having to deal with a

nightmare of cables and connectors

All PowerCom® hardware uses Fleetwood’s

patented technology, which is unique in

marketplace to provide two-way communication

with the keypads. This design ensures that no

responses are missed by requiring a keypad to

retransmit the user’s response until it is

properly received by the Base Station. The

design also allows the system to refuse to

acknowledge any invalid entries. This is clearly

superior to other technologies using one –way

radio or infrared, which do not provide

acknowledgement to the keypad when its entry

is received and do not have any way of rejecting

invalid entries.

Figure 1. System Diagram

The Base Station is the control center for the

system and operates according to commands

issued by the application software. The Base

Station can be set to any of the 75 available

channels through the software. Each Base

Station can process responses from up to 500

keypads.

A radio frequency packet is continuously sent

out by the base station when the unit is

powered on. Each base station’s packet can only

be heard by keypads that have been set to the

same channel

3.0 System Description and

Setup

3.1 Room Layout

Figure 2. Typical Room Layout

3.2 Placement of the PowerCom Mini

System

The Base Station can be located anywhere in the

area where the keypads are to be used.

PowerCom Mini keypads can operate in a room

up to 650’ x 650’feet (WRS970-DSIH or

WRS970DSI) in size. Despite a robust

communication system, walls and some other

2.4 GHz devices can moderately to severely

limit the system’s overall performance. If

coverage of a larger area necessary, elevation

of the Base Station or centering in room can

usually improve the reception of the keypad

signals.

Note: Due to the properties of signals operating

at 2.4 GHz, we does not recommend placing any

walls between the base station and the keypads.

The material in a wall tends to absorb the RF

signal and some reduced performance might be

observed.

4.0 How to Use the PowerCom

Mini (WRS7000-DSI-5)

Figure 3. PowerCom Mini keypad

4.1 Powering On

Any key will turn on the keypad. After about 12

seconds, the keypad will automatically power

itself off. The keypad will turn off after

successfully sending a vote.

4.2 Voting

Make sure a base unit is ready to collect votes.

(See appropriate user manual for base station

operation)

There are five number keys that correspond to

values 1-5. When pressing any key, the Green

LED will light to indicate the keypad has turned

on.

The keypad listens for a polling base on the

same Base ID. If the keypad is queried by the

base, the vote is sent. If successful, the green

LED will turn off. A low battery warning may

present itself after the keypad has voted. The

battery warning is the red LED will blink quickly

4 times.

If the keypad is unable to send the vote after

period of 9 seconds, the Red Led will light to

indicate the transfer was unsuccessful. There

are several reasons a vote is not able to

transmit, first, the Base ID of the base may not

be querying the keypad (system not set up to

poll enough keypads or possibly even polling) or

the keypad is out of range of the base unit.

4.3 Key Lockout

The keypad allows for the base unit to lock out

some or all of the five available keys. When a

key is locked out, it will light very briefly the

green LED and then go immediately to red. The

keypad will continue to listen to the base unit if

the key is unlocked during the polling and will

transmit. If another key is not selected during

this time, the keypad will turn after 12 seconds

to conserve battery life.

5.0 Static mode keypad

A keypad in Static mode is configured to a

specific Base ID and address. Each keypad on a

system must be set to the same Base ID of the

Base Station to be used. The address of each

keypad in a system must be a unique number

between 1 and 500.

To obtain best system performance, start at

address 1 and continue up to the number of

keypads to be used.

Once the system is configured, the settings are

maintained indefinitely. The keypad can only be

used on the Base ID it is programmed. If more

flexibility is desired (moving a keypad from base

to base or room to room, for example) use

Dynamic mode operation.

Note: PowerCom Mini only supports Static

address mode, no Dynamic mode operation.

6.0 Keypad Settings Retrieval

6.1 Keypad locally

To verify what settings the keypad has, press

the 1 and 5 key simultaneously for 3 seconds.

Either the red or the green led will light to start

a sequence of blinks representing the Base ID

and keypad address. A green LED flash

represents the numerical values separated by

red LED indicator. The format is as follows:

Tens Digit of Base ID

Red Flash

Ones Digit of Base ID

Red Flash

Small Pause

Hundreds digit of keypad Address

Red Flash

Tens digit of keypad Address

Red Flash

Ones digit of keypad Address

Red Flash

6.2 Changing Keypad and Channel Number

Make sure base station is detected properly.

Choose “Change Keypad Channel and

Address” from the drop down menu of the

Device group in Powercom Tab. Follow the

instructions to continue.

7.0 Keypad Battery Replacement

Each keypad is powered from a single CR2032

Lithium Coin Cell battery. One fresh CR2032

battery can last for up to 20,000 votes.

INSTRUCTIONS :

1. Remove screw from case back.

2. Separate case parts at screw location

3. Using a non-metallic object, carefully push

the battery out of the retainer from the

back side

4. Slide in new battery with positive side away

from circuit board

Figure 3. Keypad Battery Replacement

8.0 Software

PowerCom® is PowerPoint Add-in software

available for keypad and it can be installed for

Office 2007, Office 2010 and Office 2013. Please

contact powerco[email protected] for more

information about PowerCom software.

9.0 Accessories

Call PowerCom team or an authorized dealer for

information on available storage/shipping cases,

lanyards, extra cables or power supply kits for

PowerCom Mini system.

10.0 Limited Product Warranty

PowerCom® warrants its serial components for a

period of 24 months from the date of

manufacture for any material or workmanship

defect in the product. This warranty does not

extend to batteries or any product component,

which has been subjected to misuse, neglect,

accidental breakage, improper installation, use

outside of present guidelines, or alteration

outside of our factory.

PowerCom Base Stations and Keypads use

internal antennas built directly on the printed

circuit board. Modifying the antennas in any way

will result in reduced range and will void the

warranty.

There are no user serviceable parts inside

PowerCom Base Stations or Keypads. PowerCom

agrees to remedy, at the factory, any product

defect, or at its discretion, replace any

component or part of the product provided the

owner complies with the following procedures:

1. The owner is to determine that the problem

is not the battery or a faulty or improper

connection with the personal computer or

power source.

2. The owner will contact PowerCom during

standard hours Monday through Friday 9:00

AM to 5:00 PM Eastern Standard Time at

212-997-2000 or [email protected] to

obtain a Return Material Authorization

(RMA) number prior to shipping the product

back to the factory.

3. The owner will send the defective

component via prepaid freight to:

Fleetwood Group, Inc.

Electronics Division

Product Service Coordinator

RMA#:

11832 James Street

Holland, MI 49424

4. If the factory determines the defect is due to

negligence or oversight on the part of the

owner, the owner will be invoiced for the

cost of the repair.

11.0 FCC, IC, and EU Compliance

Information

WRS7000DSI-5 contains N240D RF Module

Responsible Party Pertaining to the Declaration

of Conformity

Fleetwood Group, Inc.

11832 James Street

Holland, MI 49424

Attn: Product Service Coordinator

Phone: 888-467-3759

12.0 Standards and Guidelines

This device complies with the following

European Directives and USA/Canada

Regulations:

Directive 1999/5/EC on radio equipment and

telecommunication terminal equipment and

the mutual recognition of their conformity

Directive 2006/95/EC on the harmonization

of laws of member states related to

electrical equipment designed for use within

certain voltage limits.

The USA Federal Communications

Commission (FCC) Rules and Regulations.

Industry Canada Rules and Regulations

This device complies with the following national

and international standards:

EN 301 489-1 V1.6.1: 2005: EMR; EMC

standard for radio equipment and services.

Part 1: Common technical requirements.

EN 301 489-17 V1.2.1: 2002: EMR; EMC

standard for radio equipment and services.

Part 17: Specific conditions for 2.4 GHz

wideband transmission systems and 5 GHz

high performance RLAN equipment.

EN 300 328 V1.7.1: Electromagnetic

compatibility and Radio spectrum Matters

(ERM);Wideband transmission systems; Data

transmission equipment operating in the 2,4

GHz ISM band and using wide band

modulation techniques.

EN 60950-1: 2001 + A11: 2004: Information

technology equipment –Safety. Part 1:

General requirements

FCC Part 15B, 15.247: 10-01-2006: Radio

Frequency devices: Operation within the

bands 902-928 MHz, 2400-2483.5 MHz, and

5725-5850 MHz.

IC RSS-210 Issue 7: 2007: Low power license-

except radio-communications devices (all

frequency bands): Category 1 equipment.

13.0 FCC/IC Compliance

This device complies with Part 15 of the FCC Rules and RSS-210 of the Industry Canada Rules. Operation is

subject to the following two conditions: (1) this device may not cause interference and (2) this device must

accept any interference, including interference that may cause undesired operation of the device. The user

is cautioned that changes or modifications to the device that are not approved by the manufacturer could

void the user’s authority to operate the device.

14.0 EU Compliance

This device is a 2.4 GHz low power response system controller intended for residential and commercial

use in all EU and EFTA member states.

Notice

The base and keypad units may be susceptible to Electrostatic Discharge (ESD) and other similar fast

transient events causing system interruption. Should system interruption occur, reboot computer, reset

base unit by disconnecting and reconnecting USB cable and push any key on keypads which have powered

down.

15.0 Technical Specifications

16.0 Troubleshooting Procedures

ISSUE

POSSIBLE CAUSE

SOLUTION

Keypad does not

turn on

Battery may be inserted backwards.

Battery is dead.

Check that the positive side of the battery is

touching the coin cell retainer.

Replace the battery.

Poor RF

Performance

Base not in open area.

Base located too close to other electronic

equipment

More than one base unit on the same Base ID

Other Interference

Multiple Base Stations are too close

Keypad battery dead.

Keypad operating too far from base station.

Do not place the base inside cabinets.

Place the base away from other electronic

devices, such as TV’s, DVD/VCR players and

similar.

Check that the bases covering an area are not

on the same Base ID.

Always physically separate other radio devices

by at least 10’ (3 m). This includes WiFi,

Bluetooth, ZigBee and other similar devices.

Keep base stations separated and do not stack

units.

Replace the coin cell battery.

Move closer to the base station to see if voting

improves.

Short range with

keypads

Power level setting too low.

Interference

Check that the power level setting of the

system is appropriate for the range trying to be

achieved (Some countries have restrictions as

to the power level setting allowed. See Section

15.0).

See “Poor RF Performance”.

Keypad vote not

sending

Keypad Base ID setting and base setting are not

matched.

Change either the base or keypads so they

match.

Note: We cannot possible list all troubleshooting issues here. We only list the common hardware issues. Please

search www.powercomars.com web site to locate the issue and possible solution.

17.0 Index

Accessories, 4

Batteries, 4

Interface, 4

Patent information, ii

PowerCom Products, 1

Return Parts, 5

RF Communication, 1

RF Performance, 6

Service, 4-5

Software, 4

Static Mode, 3

Technical Specifications, 7

Troubleshooting, 8

Voting, 3

Warranty, 4

Table of contents

Other Powercom Keypad manuals

Powercom

Powercom RF2 User manual

Popular Keypad manuals by other brands

Schlage

Schlage LINK FE599 installation instructions

HOME8

HOME8 KYP1300 quick start guide

Response

Response CA2000KP Installation and operating instructions

X-keys

X-keys XK-299-VCM-SO product manual

SCS

SCS XO 502 Installation and user manual

DSC

DSC PowerSeries Neo installation instructions

Crestron

Crestron C2N-DBF12 Operations & installation guide

FLIR

FLIR JCU-3 installation instructions

Ingenico

Ingenico i3010 installation guide

Savant

Savant WPX LV06 Series Quick reference guide

Channel Vision

Channel Vision A0129 operating instructions

Russound

Russound KP4 manual

Ksenia

Ksenia ergo M installation guide

Leviton

Leviton DRKDN-C1W installation instructions

Digital Monitoring Products

Digital Monitoring Products Thinline 7060 installation guide

Videx

Videx DINPAD user manual

S4A

S4A TF1 user manual

URC

URC TKP-100 owner's manual

Powercom Mini WRS7000DSI-5 User manual

Popular Keypad manuals by other brands