PowerGistics 1T1216PMT0 User manual

100 Continental Drive, Columbus, Wisconsin 53925 USA
201-389-9940 | www.PowerGistics.com
INSTRUCTIONS FOR
USB POWER STRIP
RETRO-MOUNT
FOR TOWER OR CORE
8/10, 12/16, OR 18/20
POWER SUPPLY:
100 - 250 VAC 50/60
Hz Output of up to 2.1A
per port for sleep and
charge. For devices with
maximum power supply
of 45W or less.

2
Please read the warnings below for important safety information regarding your product.
Failure to read these warnings or to follow the instructions below could result in personal
injury or damage to your product that could void its warranty.
• DO NOT PLUG POWERGISTICS TOWERS INTO OTHER TOWERS.
MUST BE PLUGGED DIRECTLY INTO THE WALL OUTLET.
• WALL MOUNTED TOWER MUST HAVE THE BASE RESTING
ON THE FLOOR.
• SHELF WEIGHT RATING: 5 LBS PER SHELF.
In its unassembled state, small
parts present a hazard.
Ensure that any cables
extending across the oor
to your product are properly
bundled and marked to avoid
tripping or falling which may
lead to personal injury.
This product is intended for
indoor use only. To reduce the
risk of re or electric shock,
do not expose this product to
rain or moisture. The internal
components are not sealed
from the environment.
Read your power strip’s
electrical specications.
Only plug in to devices that
are approved for use with
this power strip. Connect the
supplied power strip directly
to a wall outlet. The socket-
outlet shall be installed near
the equipment and shall be
easily accessible. Do not
connect to another power
strip or use an extension cord.
Unplug when not in use.
Must be assembled by an
adult.
Do not install or use the
electrical components
of this unit during a
lightning storm.
Do not climb on, hang
from or suspend objects
from any components
of your product unless
otherwise specied.
Read the electrical
specications of any
electronic equipment
you are using with your
PowerGistics products.
Failure to read these
specications and
follow their instructions
could result in damage
to your equipment or
personal injury.
WARNINGS WARNINGS
INSTRUCTIONS FOR USB POWER STRIP RETRO-MOUNT

201-389-9940 | www.PowerGistics.com 3
2. Widen the opening in the
grommet and remove the
power cord.
1. Push out the grommet
from power cord hole in
base of Tower.
Removing power cord from grommet
3. Save grommet for
later use.
4. Ready power cord for
power strip removal.

4
3. Use a screwdriver to remove
the brackets from the top and
bottom of the Tower spine.
2. Pop off the standard
power strip from the
brackets.
Standard Power Strip #1 (with wide vertical plugins)
INSTRUCTIONS FOR USB POWER STRIP RETRO-MOUNT
1. Remove nut and
remove the ground
wire.

201-389-9940 | www.PowerGistics.com 5
Standard Power Strip #2 (with narrow horizontal plugins)
2. To remove the power
strip, use a Phillips
screwdriver to remove
the screws at the top and
bottom.
1. Remove nut and
remove the ground
wire.

6
1. Screw the new power
strip to the spine at
the top and bottom.
Attach USB power strip
INSTRUCTIONS FOR USB POWER STRIP RETRO-MOUNT

201-389-9940 | www.PowerGistics.com 7
2. Screw the ground
wire into the screw on
the side of the spine.
Attach grounding wire

100 Continental Drive, Columbus, Wisconsin 53925 USA
201-389-9940 | www.PowerGistics.com
PWRG 1144 Mounting Kit USB power strip INSTALL GUIDE REVA 2023
1. Plug in the power cord to
the power strip.
Attach power cord
2. Widen the opening in the
grommet and feed the
power cord through.
3. Reinsert the grommet
into Tower base hole.
Plug power cord into
wall outlet.