Powerline A6 User manual

INSTRUCTION MANUAL
A6 Red Rotary Laser

2
Please read this instruction manual before operating this product.
Please store this instruction manual in the carry case for future reference.
CAUTION: Class 2 Laser Product
Do not stare directly into the laser beam from apertures.
Do not disassemble the instrument or attempt to perform any internal servicing
as this will void your warranty. No user serviceable parts included.
Only approved and authorised service technicians can carry out warranty repairs.
SAFETY

3
Laser glasses
Rechargeable
battery pack
Alkaline
battery pack
ChargerCarry case Car charger
Laser targetDetector and clampRemote control
Powerline A6
Please ensure the following items are included with your laser.
If anything is missing please contact your retailer.
ITEM CHECKLIST
INCHES CM
1
1
2
3
4
5
6
7
2
3
ON
OFF
G
G
90°
45°
10°
180°

4
G
Rotating laser port Protective lighthouse
Display screen
PRODUCT OVERVIEW
Control panel

5
90°
45°
10°
180°
G
CONTROL PANEL
Power
Speed control
Positive / clockwise rotation
LCD display screen
Tilt alarm
Negative / counter clockwise rotation
Manual / automatic mode
Grade mode
Scanning mode

6
ON
OFF
DETECTOR CONTROL PANEL
Sound on / off
Coarse / fine mode
LCD display screen Laser sensor
Bubble vial
Speaker
Power

7
G
90°
45°
10°
180°
REMOTE CONTROL PANEL
Manual / automatic mode
Grade mode
Scanning mode
Tilt alarm
Speed control
Positive / clockwise rotation
Negative / counter clockwise rotation
LCD display screen

8
USING YOUR LASER
Power Supply
‣The Powerline A6 is supplied with a rechargeable Ni-MH battery pack that is
located in the base of the unit.
‣It is recommended that the battery pack be completely charged before use.
‣Charging time is approximately 5 hours.
‣Use of the unit over time and changes in temperature may cause increases
or decreases in charging and operation time.
‣The power indicator light will flash when the battery is low. The unit should
be re-charged as soon as possible.
‣To charge the unit insert the charger into the port on the battery pack.
Progress will be shown by the power indicator display on the charger as below:
Red (flashing) = Charger and battery are not connected.
Red (constant) = Battery is charging.
Green (constant) = Battery is charged.

9
Horizontal Set Up
‣Select a place as close as practical to the work site.
Ensure the location is clear of traffic.
‣Attach the laser to a tripod and place on a level surface.
Ensure the unit is secured correctly and tightened in position.
Vertical Set Up
‣Select a place as close as practical to the work site.
Ensure the location is clear of traffic.
‣Place the laser onto a level surface with the control panel facing upwards.
Operation
‣To turn the unit on press the power switch. Self levelling will commence
and the laser will begin to rotate.
‣If the unit is outside the self levelling range the unit will not level causing
the laser beam to flash continuously.

10
Tilt alarm
‣Once the unit has been levelled off the tilt alarm can be enabled by pressing
the tilt alarm button. The tilt alarm indicator light will flash for approximately
15 seconds. Once the light is constant the alarm is enabled.
‣If the unit is disturbed while the alarm is active the unit will need to be
powered off and on again to reset its level position.
Speed control
‣Press the speed control button to cycle through various rotational speeds.
Scanning mode
‣To focus the laser beam between two points press the scanning mode
button. Pressing the button multiple times will adjust the angle of the beam.
‣To cancel scan mode press the scanning mode button several times
to cycle through to full rotation.
Rotation
‣Whilst the unit is in scanning mode press the positive / clockwise or
negative / counter clockwise button to change the rotation of the laser head.