Powerline X2R User manual

INSTRUCTION MANUAL
X2R Red Crossline Laser

2

3
Please read this instruction manual before operating this product.
Please store this instruction manual in the carry case for future reference.
CAUTION: Class 2 Laser Product
Do not stare directly into the laser beam from apertures.
Do not disassemble the instrument or attempt to perform any internal servicing
as this will void your warranty. No user serviceable parts included.
Only approved and authorised service technicians can carry out warranty repairs.
SAFETY

4
Carry case
Laser glasses
Batteries
Indoor tripodLaser target
Levelling base
Powerline X2R
Please ensure the following items are included with your laser.
If anything is missing please contact your retailer.
ITEM CHECKLIST
INCHES CM
1
1
2
3
4
5
6
7
2
3

5
Vertical laser port (x1)
PRODUCT OVERVIEW
Horizontal laser port (x1)
Control panel
Power / locking switch

6
PULSE
CONTROL PANEL
Battery indicator
Line mode
Pulse mode indicator
Pulse mode
Lock indicator

7
MODE
DETECTOR CONTROL PANEL*
Sound on / off
Laser sensor
Power indicator
Coarse / fine mode indicator
Coarse / fine mode
Bubble vial
Power on/off
Direction arrows
*The detector is an additional accessory which can be purchased from your retailer.

8
USING YOUR LASER
Setting Up
Power Supply
Operation
‣Select a place as close as practical to the work site.
Ensure the location is clear of traffic.
‣Place the laser on a level surface such as a bench or mount.
‣The X2R is powered by three AA alkaline batteries.
‣To turn the unit on slide the power switch to “on” position.
Self levelling will commence and the beams will appear.
‣If the unit is outside the self levelling range the unit will not level
causing the speaker to beep and the laser beam to flash repeatedly.
‣Press the line mode button on the control panel to cycle through
the active beams.

9
Using the levelling base
1 2 3
‣Unscrew the laser adapter from the centre of the levelling base.
‣Screw the laser adapter into the base of the unit until firm.
‣ Insert the laser adapter into the levelling base and push forward to
secure into place.
‣ For storage, follow the steps in reverse order.
laser adapter

10
Using Your Detector*
‣Press the pulse button on the control panel on top of the laser to
enter into pulse mode.
‣Switch the detector on and move it into the path of the laser beam.
‣Hold the detector upright for horizontal beams. Rotate the detector 90°
for vertical beams. The direction arrows will indicate the position of the
laser beam. The centre LED will indicate alignment with the beam.
MODE
MODE
*The detector is an additional accessory which can be purchased from your retailer.

11
CARE AND MAINTENANCE
‣This is a precision instrument and should always be transported
within the carry case provided.
‣Always turn the on/off lock to “off” when transporting the unit.
‣Whenever possible, store the instrument in a dry, shady location.
‣The X2R should be calibrated every 6 months, if ongoing accurate
levelling is required or an impact has occurred.
‣The operator should check the X2R for accuracy before precision
levelling is attempted.
‣Clean the instrument with a dry, soft cloth after use in dusty, damp
or wet conditions before storing.
‣Smudges and fingerprints may be removed with a damp tissue
or a soft, lint-free cloth.

12
WARRANTY
The Powerline X2R comes with a 3 year manufacturers warranty.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure
and for compensation for any other reasonably foreseeable loss or damage. You
are also entitled to have the goods repaired or replaced if the goods fail to be of
acceptable quality and the failure does not amount to a major failure.
Separate to the above Australia Consumer Law, Spot-on oers a global warranty.

Customer Support
To assist you with any queries or technical questions please contact the
customer support line: 1300 658 338
30 Day Free Service
If your laser is out of calibration within the rst 30 days of purchase you
are entitled to a free calibration adjustment. For more information please
contact your retailer or Spot-on.

14
SPECIFICATIONS
Specications Powerline X2R
Product code 50060
Warranty 3 Years
Accuracy ±2mm at 10m
Range 50m (detector)
Levelling range ±4°
Laser class 2 Red
Battery life 10 hours
Battery type 3x AA
Vertical lines 1
Horizontal lines 1
IP rating 54
Weight (kg) 0.45
Dimensions (mm) 95x60x115

15

www.spoton.com.au