powersoft WM Touch User manual

Keep this manual
for future reference
©2021 Powerso
USER GUIDE
WM Touch
DO000XXX R0

2 | WM Touch
Overview
The WM Touch is a PoE fed wall-mounted touch screen soluon aimed at remotely controlling audio system func-
onalies, such as zone level and source selecon, system scenes recall, and system on/o.
The WM Touch can be used for two purposes:
•Mainly, as a dedicated wall-mounted touch screen for system control, including that of zones and sources.
Controls are shared over the network via ethernet cable, and mulple touch screens can be used in the same
system.
•As a host for oponal system control user interfaces (Views) that can be accessed from Powerso’s SYS Control
mobile app, or from a tablet or PC web browser (Web Views). In other words, with the appropriate congura-
on, whenever a WM Touch is present in the network, users are also able to control the system via the app or
web browsers.1
1 When using mobile phones and tablets, a router will be necessary to connect these devices to the system control network.
One WM Touch alone can handle the controls of an enre system of Powerso ampliers. It is not necessary to
keep ArmoníaPlus or a dedicated PC running to access these system controls.

WM Touch | 3
A PoE injector or PoE switch is necessary for powering the WM Touch and a regular Cat5 cable (or above) can be
used for connecon. The WM Touch must always be in the same network that is connected to the control ether-
net ports of the ampliers, as indicated below.
Compability
The WM Touch is a perfect match for controlling the Mezzo A and AD Series amplier plaorms, and it is also com-
pable with the Duecanali DSP+D, Quarocanali DSP+D, Oocanali DSP+D, X Series, and T Series ampliers.
Duecanali
Quarocanali
Mezzo
Oocanali
STATUS
NETWORK
SIGNAL
70V
100V
25V
CAL
6s
3s
I4 I3 I2 I1 5V
-10 dBV
4 IN 3
MAINS
2 1
2 IN 1 OUT4 3
MEZZO 322 AD
SWITCHED
CTRL +CTRL +
CTRL
STATUS
NETWORK
SIGNAL
SWITCHED
70V
100V
25V
CAL
6s
3s
CTRL +CTRL +
CTRL
I4 I3 I2 I1 5V
-10 dBV
4 IN 3
MAINS
2 1
2 IN 1 OUT4 3
MEZZO 602 AD
SWITCHED
CTRL +CTRL +
CTRL
STATUS
NETWORK
SIGNAL
70V
100V
25V
CAL
6s
3s
I4 I3 I2 I1 5V
IN2 1
-10 dBV
4 IN 3
MAINS
4 3 2 1
2 IN 1
MEZZO 324 AD
STATUS
NETWORK
SIGNAL
SWITCHED
70V
100V
25V
CAL
6s
3s
CTRL +CTRL +
CTRL
I4 I3 I2 I1 5V
IN2 1
-10 dBV
4 IN 3
MAINS
4 3 2 1
2 IN 1
MEZZO 604 AD
PoE
Injector*
PoE
Injector*
PoE
Injector*

4 | WM Touch
Conguraon
The WM Touch control interface layout is pre-dened and will automacally adapt to the dierent user congura-
ons, including screen orientaon. Some basic set-up can be performed directly on the WM Touch, whilst more
advanced conguraons will require the soware ArmoníaPlus (version 2.1 or later).
Soware Conguraon
In ArmoníaPlus, a new virtual WM Touch can be added to the Workspace from Design > Controls and by clicking
the WM Touch icon in the top bar.
Alternavely, online panels already connected and available in the network can be dragged and dropped to the
Workspace from the Discovery bar (Design > Match).
Once a WM Touch is in the Workspace, under the Design > Control, select one or more panels and proceed with
the conguraon from the ribbon menu.
From the ribbon menu, it will be possible to:
1. Edit the WM Touch name. This will be the name displayed on the device itself.
2. Select the control funcons to be displayed on the WM Touch.
• Zone Level – displays level and mute controls for the zone(s) selected.
• Source Selecon – enable users to choose from the dierent sources available for the zone(s) selected.
• Scenes Recall – enable users to choose from the dierent scenes (system conguraons) created for the
system.
• System On/O – displays an on/o buon.
3. Select the zones to be controlled by the panel. This opon will only be available if either ‘Zone Level’ or ‘Source
Selecon’ boxes are cked.
4. Perform addional conguraons, such as:
• Selecng the me for the screen lock acvaon (only available for online devices). The mer can also be
congured locally on the WM Touch itself.
• Enabling and seng a 4-digit passcode for exing the screen lock.
• Loading a custom logo to be displayed in the screen lock window.
Just like with Powerso ampliers, the IP address of the WM Touch can be congured under Cong > IP. This op-
on is only available for online devices.
42 31

WM Touch | 5
Local Conguraon
Language and Screen Orientaon
The start-up screen of the WM Touch allows the
conguraon of the screen orientaon mode and the
interface language.
Idenfy
The start-up screen also displays an ‘Idenfy’ buon.
When pressing this buon, the matching device will be
highlighted in ArmoníaPlus, under the Discovery bar
(Design > Match). The ‘Idenfy’ buon is also available
in the ‘Hidden Sengs’ menu.
Hidden Sengs Menu
Aer the WM Touch has been congured with Ar-
moníaPlus, and the system is already running, it is sll
possible to change the Language and Screen orienta-
on from the ‘Hidden Sengs’ menu. To access the
menu, select ‘More’ from the main ribbon menu (only
visible when the system is running). Press and hold the
‘Project Info’ icon for 2 seconds and release.
Screen Lock & Timer
The touch screen can be manually locked by pressing
More > Lock Screen. By default, the screen will auto-
macally be locked aer 30 seconds of inacvity and
the display brightness will be reduced. This mer can
be changed to a set of predened values from the ‘Hid-
den Sengs’ menu.

6 | WM Touch
Operaon
The WM Touch will automacally adapt to the dierent user conguraons selected, including dierent screen
orientaon modes. Addionally, the layout will change depending on how many zones the screen has been cong-
ured to control.
Single Zone Operaon
When the WM Touch has been congured to control
one single zone, the acve source playing in that zone
can be selected from the dropdown menu on the top of
the screen (A). The volume can be controlled using the
circular slider and pressing the speaker icon will mute/
unmute the zone (B).
Scenes Selecon
Scenes can be accessed from the ribbon menu (A).
Once inside the Scenes window, load a dierent system
conguraon by pressing the selected scene on the
screen, holding unl loading is full (B), and releasing.
Mul-Zone Operaon
In a mul-zone conguraon, it is possible to control
mulple zones simultaneously, either by manually se-
lecng each zone or by using the ‘Select All’ buon (A).
Once one or more zones have been selected, it will be
possible to select the source playing in those zones
(B), mute/unmute them (C), and adjust their level (D).
When mulple zones are selected, the level changes
applied will maintain the relave level dierences be-
tween them.
A
B
D
A B C
A
B

WM Touch | 7
System ON/OFF
The system on/o control can be accessed via the
‘More’ icon in the ribbon menu (A). A new window will
be opened from where the system can be turned on/
o by pressing the dedicated buon (B), holding it unl
loading is full, and releasing.
B
A

8 | WM Touch
Troubleshoong
In some rare cases, the WM Touch may display the message “Update Failed” following a reboot or rmware
update. This means that the device rmware needs to be updated and the conguraons re-loaded to the WM
Touch. Follow the procedure below to recover the device.
1. From a computer connected to the same network of the WM Touch, type in the IP address of the device in any
web browser, followed by /recovery. This will open the WM Touch Recovery page from where the rmware can
be updated (see below).
If you have a mobile phone connected to the same network of the WM Touch, you can use the QR code pro-
vided on the screen to access the recovery page.
Please note that while connected to the recovery page, the device will not show up in the ‘Discovery’ tab in
ArmoníaPlus.
2. If the computer is connected to the internet, it will be possible to download the latest rmware version (Step 1).
Alternavely, you can manually upload a le containing the rmware update (Step 2).
3. Click on ‘Update’ to start the updang process. This may take a few minutes.
4. Once the update is nished, close the WM Touch Recovery page.
5. In ArmoníaPlus, go to the ‘Controls & Views’ opons on the top right corner of the screen and stop the system
currently running.
6. Reload the conguraons to your WM Touch from the Discovery bar (Design > Match).
7. Run your system again.

WM Touch | 9

DRIVING HUMAN AUDIO EXPERIENCE
POWERSOFT S.P.A.
Via E. Con, 5 - Scandicci (FI) 50018 - Italy
support@powerso.com
[phone]
[phone]
POWERSOFT.COM