Powr-Flite PEB Installation and operation manual

OPERATOR’S MANUAL & PARTS LIST
WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL
COMPLETELY BEFORE OPERATING THIS EQUIPMENT.
©Tacony, Inc., All rights reserved
Save These Instructions
POWR-EXTRACTOR BRUSH
MODEL PEB
X8440 PEB-Man 3/2016

Check the carton carefully for
signs of rough handling. Remove
the machine from the carton. If
the machine is damaged, notify
the carrier immediately and
request an inspection. Be sure to
keep the carton, packing inserts,
packing lists and carrier receipt
until the inspector has verified
your claim.
Powr-Flite's liability ceases when
the shipment is picked up by the carrier, but our cus-
tomer service staff will be glad to furnish any
information needed in connection with the claim and
will expedite the repair of the machine.
Read the manual carefully and completely
before attempting to operate the unit. This
manual has important information for the
use and safe operation of this machine.
Keep this manual handy at all times. This machine
will assure years of satisfactory service if operated
and maintained according to recommendations in the
manual.
To protect your investment, promptly fill in the
required information on the warranty card included
with the unit. Then mail the card back.
• To avoid electric shock, do not expose to rain.
Store indoors.
• To avoid fire, do not use machine in
environments where combustible liquids, vapors
or dust concentrations are present.
• Do not expose the machine to freezing
temperatures.
• Do not use this machine for totally dry
vacuuming. The PEB is not fitted with a fine
dust filter.
• Do not use cleaning chemicals in this machine
except those recommended for steam type
extraction equipment. The use of any chemical
with abrasive additives voids the warranty.
• Do not break off or pull out the grounding prong
on the plug.
• Do not attempt repair on a warranted machine
unless proper repair instructions by an authorized
shop are obtained from the factory.
• Do not use any replacement parts except those
specified on the parts list. Proper performance of
the machine could be affected if substitutions are
made.
• Solution Lines and Fittings
Flush the machine at least once a month
with a solution of 1 part water to 3 parts
white vinegar in order to neutralize the
alkaline residue left by the cleaning solution.
• Vacuum Hose
Rinse out vacuum hose thoroughly prior
to storage.
• Rotational Brush
Remove string, carpet fiber and lint from
rotational brush to prevent circuit overload
(see back page for circuit breaker reset switch
illustration).
• Spray Jets
Inspect the spray jets for wear. Clean or
replace the jets if necessary.
WHEN THE MACHINE IS DELIVERED
BEFORE OPERATING THE MACHINE
WARRANTY
WARNING
PERIODIC MAINTENANCE
POWR-EXTRACTOR BRUSH - MODEL PEB

Slide adjustable clamp into desired position.
1
Tighten knob to secure hose ring into place.
3
Insert hose ring bolt into clamp.
2
Connect the female power cord receptacle with
the male plugged pigtail attached at the switch
housing.
4
Attach the solution hose female connector to
the male connector located on top of the
Powr-Extractor Brush housing.
6
Push the vacuum hose cuff into the stainless
steel manifold tube inside the middle of the
Powr-Extractor Brush housing.
5
Vacuum Hose/Solution Hose/Power Cord Assembly to PEB

1. Turn on all vacuum and pump switches at the
extractor unit.
2. Turn on the PEB solution switch (1).
To Extract:
Guide Powr-Extractor Brush backwards, overlap-
ping each pass slightly, depressing either left or
right brush control lever (2) to apply solution,
rotationally brush and extract.
To Wet Vacuum and Brush:
To wet vacuum and brush only without applying
additional solution, place the solution switch in
the off position and depress either brush control
lever.
To Wet Vacuum Only:
Place solution switch in the off position. Operate
Powr-Extractor Brush without depressing either
control lever.
To Prespray:
Place solution switch in the on position. Tilt
Powr-Extractor Brush back while depressing
either brush control lever.
This Powr-Extractor Brush should be grounded
while in use to protect the operator from electric shock.
This machine is equipped with a 3-conductor cord and
a 3-prong grounded type attachment cap plug to fit the
proper grounding type receptacle. The green (or green
and yellow) conductor in the cord is the grounding
wire. Never connect this wire to anything other than the
grounding blade.
The Powr-Extractor Brush is provided with an
attachment cap plug, as shown in Sketch A, and is
intended for use on a nominal 120 volt circuit. If a prop-
erly grounded receptacle, as shown in Sketch A, is
unavailable, an adaptor, as shown in Sketch C, is
available and should be installed, as shown in Sketch B,
if the outlet box that houses the receptacle is grounded.
Be sure to fasten the grounding tap to the faceplate
screw.
Dual Brush
Control Levers
Circuit Breaker Overload
for Brush Motor
Solution
ON/OFF Switch
METAL SCREW
COVER OF GROUNDED
OUTLET BOX
( B )
( A )
GROUNDING PIN
GROUNDING
MEANS
ADAPTER
( C )
POWR-EXTRACTOR BRUSH OPERATION
SAFETY INSTRUCTIONS
ONE LAST REMINDER!
READ ALL INSTRUCTIONS, WARNINGS AND CAUTIONS BEFORE USING
WARNING
TO AVOID FIRE, DO NOT USE WITH A
FLAMMABLE OR COMBUSTIBLE LIQUID
TO CLEAN FLOOR.
These guidelines are presented for your protection
and convenience. Please read them carefully, since a
failure to heed these precautions could result in
discomfort or injury. When using an electrical
appliance, basic safety precautions should always be
followed.

A Tacony Company
3101 Wichita Court • Ft. Worth, TX 76140-1755
1-800-880-2913 • Fax: [phone] • www.Powr-Flite.com
X8440 PEB-Man 3/2016