Powr-Flite PFX900S User manual

WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL COMPLETELY
BEFORE OPERATING THIS EQUIPMENT.
Self-Contained Carpet Extractor
OPERATORS MANUAL AND PARTS LIST
Model PFX900S
X8686 1/06
ATacony Company
3101 Wichita Court • Fort Worth,TX 76140
1.800.880.2913
OPERATING INSTRUCTIONS
COMMERCIAL AND HOUSEHOLD
SELF CONTAINED EXTRACTOR

–2–
READ ALL INSTRUCTIONS BEFORE USING!
CARE OF THIS SELF-CONTAINED EXTRACTOR
Treat this unit as you would any other high grade precision
made product. Dropping, unreasonable bumping across
thresholds and other misuses may result in a damaged
unit which will not be covered by warranty. When not in
use, power cord should be wrapped around handle for
storage.
Read this manual completely before operating this extrac-
tor. It is important to follow instructions in this manual to
prevent the possibility of injury or damage to the user
and/or machine.
Congratulations on purchasing a Powr-Flite self-contained
extractor. Given proper care, this product will afford you
many years of trouble-free operation. All parts have
passed rigid quality control standards before being assem-
bled to produce the finished product.
Prior to packaging, the extractor is again inspected for
assurance of flawless assembly. This unit is protectively
packed to prevent damage in shipment. We recommend
removal and inspection of unit upon delivery for possible
damage in transit. Only a visual examination will reveal
damage that may have occurred.
If damage is discovered, immediately notify the transporta-
tion company that delivered your extractor. As a shipper,
we are unable to report claims for concealed damage.
You must originate any claim within 5 days of delivery.
This manual is for your protection and information.
PLEASE READ CAREFULLY since failure to follow
precautions could result in discomfort or injury. When
using electrical equipment, basic safety precautions should
always be followed.
TABLE OF CONTENTS
INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
SAFETY PRECAUTIONS (English) ...................3
GROUNDING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . 4
SAFETY PRECAUTIONS (Spanish) (French). . . . . . . . . . . 5
GENERAL INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . 6,7
Machine Components . . . . . . . . . . . . . . . . . . . . 6
Machine Operation. . . . . . . . . . . . . . . . . . . . . . . 6
Pre-operation Checks .....................6
Cleaning Procedure (accessories) . . . . . . . . . . 7
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Routine Care & Maintenance . . . . . . . . . . . . . . 7
ILLUSTRATED PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . 8-11
MAINTENANCE GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . 12

–3–
GROUNDING INSTRUCTIONS
DANGER:Improper use of the grounding plug can result
in a risk of electric shock.
GROUNDING INSTRUCTIONS
GROUNDING METHODS
NOTE: In Canada, the use of a temporaryadapter is not permitted
bythe Canadian Electrical Code.
This extractor must be properly grounded. If it should malfunction or breakdown, grounding provides a path of least resis-
tance for electrical current to reduce the risk of electric shock. This machine is equipped with 1 or 2 pigtail cords having
an equipment-grounding conductor and grounding plug. The pigtails must be inserted into an appropriate 12 gauge 3
prong extension cord.
This unit is for use on a nominal 120 volt circuit and has a
grounded plug that looks like the plug illustrated in (Fig. A).
WARNING!
Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
Check with a qualified electrician or service person if you are in doubt as to whether the outlet is
properly grounded. DO NOT modify the plug provided with the appliance. If it will not fit the out-
let, have a proper outlet installed by a qualified electrician.

–4–
IMPORTANT SAFETY PRECAUTIONS
WARNING!: To reduce the risk of fire, electric shock, or injury
When using this self contained extractor,basic precautions
should always be followed, including the following:
1) DO NOT leave unit when plugged in. Unplug from
outlet when not in use and before servicing.
2) DO NOT allow unit to be used as a toy.Close
attention is necessary when used around or near
children.
3) Use only as described in this manual. Use only
manufacturer’srecommended attachments.
4) DO NOT use with damaged cord or plug. If unit is
not working properly because it has been dropped,
dropped into water, left outdoors, or damaged in any
way, contact a service center of Powr-Flite®.
5) DO NOT pull or carry by cord, use cord as a handle,
close door on cord, or pull cord around sharp edges
or corners. DO NOT run unit over cord. Keep cord
away from heated surfaces.
6) DO NOT unplug by pulling on cord. Tounplug, grasp
the plug, not the cord.
7) DO NOT handle plug or appliance with wet hands.
8) DO NOT put any objects into openings. DO NOT use
with any opening blocked: keep free of dust, lint,
hair,or anything that may reduce air flow.
9) Keep hair, loose clothing, fingers, and all parts of
body away from openings and moving parts.
10) DO NOT pick up anything that is smoking or
burning such as cigarettes, matches, or hot ashes.
11) DO NOT use to pick up hazardous chemicals.
12) Turn off all controls before unplugging.
13) Turn unit offimmediately if foam or liquid comes from
machine exhaust. Empty and clean out recovery
(dirty) tank and use defoamer to correct the problem.
14) DO NOT use to pick up flammable or combustible
liquids such as gasoline or use in areas where they
may be present.
15) DO NOT use where oxygen or anesthetics are used.
16) Extension cord must be a three-wire type, 14 guage
or larger,to ensure grounding protection.
17) Replace damaged or worn parts immediately with
genuine original equipment parts to maintain safety.
18) This unit must be connected to a properly grounded
outlet only. See grounding instruction.
WARNING
To avoid fire, DO NOT use
with a flammable or
combustible liquid to
clean floor.
WARNING
To avoid electric
shock, DO NOT
expose to rain.
Store Indoors.

–5–

–6–
GENERAL INSTRUCTIONS
1) Fill the solution tank with 9 gallons of warm water.
WARNING: DO NOT overfill.
2) Measure carpet cleaning solution per manufactur-
ers recommended ratio into the clean water tank.
DO NOT use the waste tank to fill the solution
tank as debris could damage the pump or block
the jet. WARNING: DO NOT exceed 150° (65° C)
3) Add defoamer solution per manufacturer’s instruc-
tions as needed.
PRE-OPERATION INSTRUCTIONS for PFX900S
OPERATION OF SELF-CONTAINED CARPET CLEANER
NOTE: (color fastness) Before using carpet cleaning chemicals, test on an inconspicuous part of the carpet for color fastness.
Place the solution on a small piece of clean white material or tissue, then rub the carpet vigorously. Excessive amounts of dye showing
onthe material would indicate that the colors are not fast, and should not be wet cleaned.
1) Plug main power cable into outlet.
WARNING: This machine must be properly
grounded.
2) Press the Vac switch to the ON position. Then
press the pump switch ON and the brush switch to
the ON position.
3) Lower carpet brush. Push brush lowering pedal
forward to lower brush. Push down and back to
raise bush.
4) Press and hold the solution switch to apply the
cleaning solution. Pull the machine backwards at
the same time to clean the carpet. Stop the solu-
tion spray about 12” (30cm) before the end so all of
the solution is vacuumed up. Slightly overlap the
next cleaning pass to prevent streaking. Atwo (2)
wet pass maximum is recommended to avoid over-
wetting. After a few passes, check the waste tank to
see that no foam is present. Add extra defoamer if
necessary.
5) Make sure to empty the recovery (top) tank when it
is approximately 3/4 full. Do not refill the solution
tank without emptying all the contents of the recov-
ery tank first.
Solution switch
Solution tank
Recovery tank
Vac shoe
Brush and spray
Brush lowering
pedal

–7–
DAILY/INTERVAL
1) Check the spray jet for blockage and a uniform spray pattern. Remove jet and blow through to clean. Do not use a
pin as this may cause damage to the jet.
2) Check and remove any debris or lint build-up from the vacuum head, brush, and brush housing.
3) Always wash out the tanks with clean water after use. To do this, pour clean water into the solution tank and spray
through spray tip to clear chemical residue from the pump, lines, and spray tip. Allow the vacuum to run for a few
minutes after use to aid the machine in drying out and to help prevent bacteria and odors.
WEEKLY
1) Inspect hoses (unseen blockages sometimes occur), hose cuffs, and the rubber seal on the recovery tank lid. The
main cable, plug, and switches should also be examined for damage.
NOTE: It is advisable to store the unit with the recovery tank lid removed.
CAUTION: THIS UNIT MUST BE PROTECTED FROM FREEZING.Damage from freezing could cause machine to
malfunction.
GENERAL INSTRUCTIONS
STORAGE
WHEN CLEANING IS FINISHED:
1) Connect the drain solution hose (gray hose with
brass connector) to the solution fitting at the front of
the machine and place the other end at drain. Turn
on the PUMP switch. This will pump the remaining
solution into the waste tank for easy drainage.
2) To disconnect the solution hose, push in on the ring
of the solution filling. Switch off the machine,
remove power plug from the socket, and empty the
waste tank. Leave waste tank open when storing.
3) Leave brush raised for storage.
ACCESSORIES / TOOLS (OPTIONAL)
For upholstery cleaning and inaccessible areas.
Attach recovery hose to recovery hose position of vac-
uum shoe. Connect the accessory solution hose to the
solution fitting at the front of the machine by pushing
back the locking ring to fit. Turn on vacuum and pump.
ROUTINE MAINTENANCE INSTRUCTIONS
Tank drain hose
Brush adjustment pedal
Solution hose
connection
Vacuum hose
connection

SELF-CONTAINED EXTRACTOR PFX900S PARTS
–8–
Pump
Control Panel
Recovery Dome
Solution Tank

–9–
Brush Housing Recovery Tank
Solution Fitting
Brush Motor Base
Manifold
Brush
Vacuum Shoe

ref# order# description
BRUSH HOUSING :
1X9015 brush housing weldment
27BF008 nut
3X9004 brush drive belt
4X9003 bridge rectifier
5X8055 strain relief
6X9107 brush lift bracket
7X8256 nut
872142A plug, 7/8" black nylon
9X9030 foot pedal pin
10X9026 brush lift pedal
11X9122 safety walk tape, 1" wide, black
12 72241A washer
13X9114 e-ring
14X9128 label
15 7BS002 screw
16 7CY001 washer
1771651A screw
18 7CW003 screw
19 X8237 nut
207BR005 screw
21X8830 nut
22 7BH004 screw
BRUSH MOTOR BASE:
1X8830 nut
2X9002 motor, 120V DC
X9119 motor, 220V DC - for 220v model only
3X9099 spacer
4X9116 drive pulley
5X9118 screw
6X9015 motor cover
7X9126 gasket, brush motor cove
8X9015B belt cove
BRUSH:
1X9017 brush axle
2X9070 brush, 3” diameter x 18” chevron
3X9001 brush bearing
4X9117 brush driven pulle
5X9018 brush bearing spacer,nylon
6X9019 brush bearing shield
7X9020 brush thread guard
8X9118 screw
9X9115 washer
CONTROL PANEL:
1X9043 housing, cover, blue
2X9008 push button switch
3X9007 rocker switch
472086A circuit breaker, 2.5 amp
5X8008P strain relief, plastic
672315A power cord
7X9093 label, 3-hole switch panel
X9094 label, 3-hole switch panel - models w/heater
8PD8 strain relief
9M1409 14/8, 600 volts cord
10 X8008N nut, lock
11 72049A spring clip
12 71651A screw
13 X9135 screw
14 7DN004 nut cap
15 7CM003 washer
MANIFOLD:
1X9021 spray manifold
2X9141 miniature nozzle bod
3X9139 miniature nozzle tip
47AK003 elbow, union
5PC66 fitting, brass, 1/8 nptm x 1/4 hose bar
6X8542 hose, solution
77DL003 clamp
8X8293 washer, nylon
97CM007 washer
PUMP, 100 PSI:
1SF814 100 p.s.i. Shurflo pump, 115V
FJ2002 100 p.s.i. Shurflo pump - for 220V models only
271507A elbow, 1/2h - 3/8 mpt, 90°
3PC20 reducer,3/8” male x 1/4" female
4PX32 fitting, brass, 1/4" close nipple
57AV001 1/4 female tee
6SW132 solenoid, 120V,250 p.s.i.
SW132-5 solenoid, 220V, 400 p.s.i. - for 220v models
7PC45 1/8" close nipple
87AG002 bushing
9SW139 1/8” street elbow, 90°
10 7AT006 barb, elbow, 90
1171817A hose, 1/4" braide
ref# order# description
12 7DL003 clamp
137AT003 hose barb
14X8542 hose, solution
15 X8237 nu
16X8858 washer
17X8211 bolt
RECOVERY DOME:
1X9034 recovery tank dome
2X9124 recovery dome gasket
3X9110 knob, large dome li
4X9098 screw
5X9068 chain
67CM003 washe
7X8849 screw
RECOVERY TANK:
1X9041 recovery tank housing, blue
2X9129 vacuum stack assembl
3PX14A gasket
4X9075 bushing
572173A spring cli
6X9053 float cage
77DL005 clam
8X9120-1 vacuum motor gasket
972365A 3-stage vacuum moto
10 PX65 fitting, plastic
11X9092 vac hose w/cuff
12PX11A fitting, plastic elbow, 90°
13 X8222 screw
14 X8212 washe
15 X8213 nu
16 72605A space
17 X8289 screw
18 PAS37 drain hose
19 PAS36 plug, drain hose
20 X8262 screw
21 X9071 gasket
22 X9033 small dome
23 X9084 cover gasket
24 X9080 recovery tank float cover
25 PX46 nut, lock
26 X9142 screw
27 X9143 screw
SOLUTION FITTING:
1PX48 fitting, brass bulkhead
272274A washer
371495A pump protection filter
47AT017 barb, beaded
570079C hose, 1/2" wire reinforced
67DL008 clamp, 1/2" worm gear
VACUUM SHOE:
1X9009 vacuum shoe, aluminum
2X9013 vacuum shoe tub
3X9014 hinge
4X8222 scre
57CM007 washer
6PX6 1/4 x 1/4 female quick disconnect brass fitting
77AT003 hosebarb fitting
87DL003 clamp, 1/4" worm gear
9X9096 flip door hinge w/ spring assembly
10 X9097 gasket, flip door
117BH004 screw
12 7CL002 washer
13 X8282 bolt
14 X8209 screw
15 7CY002 washer
16 7CN001 nut
SOLUTION TANK:
1X9042 housing, solution, blue
27BS002 screw
3X8256 nut
4X9144 28" chain
5X9081 lid, solution tank
6X8235 washer
7X8209 screw
8X9086 bracket, tank mount
9X9085 bracket, tank mountin
10 X9125 label, tank capacit
11X8400A Powr-Flite label
weldment
12 X9012 main chassis
13 X9066 wheel, blac
14 X8020 washer, countersunk axle
15 X8265 screw
16 X9109 grommet
ating instruction
17 X9057 label, oper
18 X9111 cord clamp
19 X9134 brush warning label
SELF-CONTAINED EXTRACTOR PFX900S PARTS
–10 –

SAVE THESE INSTRUCTIONS
MAINTENANCE GUIDE
WARRANTY
The manufacturer warrants to the original purchaser that products manufactured are free
from defects of workmanship and material, provided such goods are installed, operated
and maintained in accordance with written manuals or other instructions for a period of
1year from date of purchase on parts and workmanship. In case you as our customer,
meet any trouble with your machine, contact your Powr-Flite® representative who will be
happy to be of service to you and will take care of the warranty settlement.
NOTE: Alterations and changes made to the machine without written approval of the
manufacturer and use of unapproved spare parts will not be covered by warranty.
Motors not running
CAUSE: SOLUTION:
1) Power not reaching main switch. 1) Check power supply. Check fuses/circuit
breaker. Contact service center.
2) Defective power cord. 2) Replace with 14 guage cord.
3) Faulty switches or wiring. 3) Contact manufacturer or service center.
4) Blown fuse or tripped circuit breaker 4) Reset circuit breaker according to operating
instructions or replace fuse if qualified..
5) Problem with brushes, field windings,
or armatures. (vacuum or brush motor) 5) Contact manufacturer or service center.
Loss of vacuum suction
CAUSE: SOLUTION:
1) Vacuum head blocked. 1) Visually inspect and clear blockage.
2) Hoses blocked. 2) Visually inspect and clear blockage.
3) Recovery tank not sealed properly. 3) Check tank for damage or adjust lid
for proper fit.
Brush not functioning properly
CAUSE: SOLUTION:
1) Belt broken. 1) Replace belt.
2) Brush jammed. 2) Visually inspect and clear blockage.
3) Clutch bearing seized. 3) Contact manufacturer or service center.
Spray jet not functioning properly
CAUSE: SOLUTION:
1) Jet blocked. 1) Visually inspect and clean according to
operating instructions.
2) Solution filter blocked. 2) Visually inspect and clean according to
operating instructions.
3) Pump head, valves or diaphram blocked 3) Contact manufacturer or service center.
or damaged.
4) Solenoid valve inoperative 4) Contact manufacturer or service center.
5 YEARS on 
One Piece 
Housing
2 YEARS on 
Brush Motor

1 YEAR on 
Parts & Our 
Workmanship