Powr-Flite PS25 User manual

Save These Instructions
X8499
Model Commercial Spotter
stock number PS25

– 3 –
*When using a commercial spotter, basic precautions should be followed, including the following: *Read all instructions before
using this commercial spotter.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
To reduce risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Do not leave commercial spotter unattended when plugged in. Turn off the switch and unplug the electrical cord when
not in use and before servicing.
• Do not allow to be used as a toy. Close attention is necessary when used near children.
• Use only as described in this manual . Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If commercial spotter is not working as it should, has been dropped damaged,
left outdoors, or dropped into water, return it to a service center before using.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull a cord around sharp edges or
corners. Do not run commercial spotter over cord. Keep cord away from heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not handle plug or commercial spotter with wet hands.
• Do not put any objects into openings. Do not use with any opening blocked, keep free of dust, lint, hair, and anything
that may reduce airflow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes. Use extra care when
cleaning on stairs. Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where
they may be present.
• Store your cleaner indoors in a cool, dry area.
• Do not unplug by pulling on cord. To unplug, grasp the plug, NOT THE CORD.
THESE MODELS ARE GROUNDED, CONNECT TO A PROPERLY GROUNDED OUTLET ONLY - SEE GROUNDING INSTRUCTIONS.
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for elec-
tric current to reduce the risk of shock. This appliance is equipped with a cord having an equipment-grounding conductor and
grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance
with all local codes and ordinances.
WARNING - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a
qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug
provided with the appliance - if will not fit the outlet, have a proper outlet installed by a qualified electrician.
This appliance is for use on a normal 120 volt circuit, and has a grounded plug that looks like the plug illustrated in sketch A.
Note: In Canada, the use of a temporary adapter is not permitted by the Canadian Electrical Code.
WARNING
IMPORTANT SAFETY INSTRUCTIONS

– 4 –
Operating Instructions for EX3S Spotter
WARRANTY
To protect your investment,
promptly fill in the required information on the
warranty card included with the unit. Then mail the
card back.
WHEN THE MACHINE IS
DELIVERED…
BEFORE USING THE MACHINE
GENERAL PRECAUTIONS
Read the manual carefully and completely before
attempting to operate the unit. This manual has
important information for the use and safe operation
of this machine. Keep this manual handy at all times.
The carpet spotter will assure years of satisfactory ser-
vice if operated and maintained according to
recommendations in the manual.
Follow these guidelines to ensure operator safety
and to maintain equipment in running order.
■Make sure the machine is plugged into an
electrical outlet with the same voltage rating as
shown on the nameplate of the machine.
WARNING
■ Do not expose the machine to freezing tempera-
tures.
■ Do not use the machine for totally dry vacuuming.
This machine is not fitted with a fine dust filter.
■ Do not use citrus-based cleaners in this machine.
■ Do not use cleaning chemicals in this machine
except those recommended for commercial extrac-
tion equipment. The use of any chemical with
abrasive additives voids the warranty.
■ Do not break off or pull out the ground prong on
the plug
■ Do not attempt repair on a warranted machine
unless instructions to perform it by an authorized
shop are obtained from the factory.
■ Do not use any replacement parts except those
specified on the parts list. Proper performance of the
machine could be affected if substitutions are made.
■ Use defoamer at all times to prevent damaging the
vacuum motor.
■ Do not use water in excess of 140° F (62° C).
■ Follow maintenance schedule strictly.
Failure to comply with the above warning
instructions will void the warranty.
Do not attempt to plug a 115 volt machine into
a 230 volt outlet or a 230 volt machine into a
115 volt outlet.
■Disconnect the power cord from the outlet before
attempting maintenance or repair work.
■Do not leave machine connected to an electrical
outlet when unattended.
■Never pull the machine by the cord or yank the
cord from the receptacle. Replace a damaged
cord immediately.
■If an extension cord is necessary, use a three
conductor grounding cord – 12 gauge wire or
heavier to prevent motor burnout and
over-heating of wires.
■To avoid electric shock, do not expose to rain.
Store indoors.
■To avoid fire, do not use machine in environments
where combustible liquids, vapors or dust concen-
trations are present.
Check the carton carefully for
signs of rough handling. Remove
the machine from the carton. If
the machine is damaged, notify
the carrier immediately and
request an inspection. Be sure to
keep the carton, packing inserts, packing lists and car-
rier receipt until the inspector has verified your claim.
Liability ceases when the shipment is picked up by
the carrier, but our customer service staff will be glad
to furnish any information needed in connection with
the claim and will expedite the repair of the machine.

– 5 –
Operating Instructions for EX3S Spotter
Basic Troubleshooting:
A. If the pump does not prime, depress the lever on the hand tool to release the air lock.
B. If solution flow is reduced or spray is weak:
1. Check for low solution level in the solution tank.
2. Check the screen on the hose in the solution tank for blockage.
3. Check the spray jet from the hand tool for blockage.
If suction is low:
1. Check the recovery tank to see if it is full.
2. Check the foam filter at the top of the recovery tank for debris.
3. Check for blockage in the hand tool or the hose.
4. Add defoamer to recovery tank
Filling the Spotter
Add water and chemicals to the solution tank in the front of
the machine.
Operating the Spotter
A. Attach the solution feed line to the quick disconnect at the
top of the machine.
B. Attach the vacuum hose to the vacuum inlet on the
recovery tank lid.
C. Turn the 3-way switch to use either the pump and
vacuum or the vacuum alone.
(Allow approximately 30 seconds for the pump to prime.)
D. Use the hand tool to spray and recover the solution.
E. The float shut-off will disenable the suction of the unit
when the recovery tank is full. The operator will notice a
distinctive change in the sound of the vacuum motor when
the shut-off is activated. Empty the recovery tank to
resume cleaning.
Cleaning the Recovery Tank
A. To drain the tank, remove the plug at the back of the
machine and tilt on wheels with the handle.
B. Make sure the foam filter at the top of the recovery tank
is clean and dry.

– 6 –
Parts Diagram
13
9
37
21
16
11
15
18
17
8
6
6
24
32
23
38
31
27
29
24
28
33
4
5
3
10
35
14
7

– 7 –
Parts List
ref. # order # description
3 PX211 Axle
4 PX206 Wheel
5 X8293 Spacer, Wheel
6 PX118B Pal Nut
7 PX207 Latch
8 PX202S Recovery Tank, w/screen, Spotter
9 PX209 Foam Filter
10 PX210 Drain Plug
11 PX40A Hinge
12 PX203G Gasket, Housing Lid
13 PX203G Lid, Recovery Tank
14 PX144S Flapper/float Assembly
15 1987 Motor, Vacuum
16 PX13 Gasket, Motor
17 PX99 Bracket, Motor
18 PX201 Solution Tank
21 PC10 Fitting, Brass,1/8 FPT X 1/8" MQD
23 FJ5082 Pump, Oscillating
24 PX204 Mount, Pump (pair)
27 PX142 Panel, Cord Access
28 M1408 Cord, 18/3, 15'
29 PD8 Strain Relief, 1/2" NPT
31 PX205 Plate, Cord Wrap
32 PX141 Panel, Switch
33 PX87A Switch, Rocker, on/off/on
34 PX48G Gasket, Bulkhead
35 X8497A Label, Switch
37 PX103A Lid, Solution Tank
38 PX143 Panel, Bottom
Not Shown
PX146 Handle
PX147 Handle Support
PX30 Strainer, Solution Tank
X8548 Hose, 1/4" ID (by the foot)
PX212 Fitting, Brass, 1/4 MPT X 1/4" HB, 90 Deg. Elbow
PX48 Fitting, Brass, Bulkhead, 3/4"
PX214 Fitting, Nylon, 1/8" MPT X 1/4" HB, 90 Deg. Elbow
X8008N Nut, Strain Relief
PX103AG Gasket, Solution Tank Lid
1507WDS Hose Assembly, 1-1/4" X 10'
X8860 Hand Tool
PX215 Clamp, Hose, 2-1/4", SS
X8294 Spacer, Cord Wrap

3101 Wichita Court • Fort Worth, Texas 76140-1710
Call Toll-Free [phone] • Fax [phone]