Powr-Flite PX1300 series User manual

WARNING: OPERATOR MUST READ AND UNDERSTAND THIS MANUAL COMPLETELY
BEFORE OPERATING THIS EQUIPMENT.
Upright Extractor
OPERATORS MANUAL AND PARTS LIST
Model PFX1300 SERIES
X8498

2
IMPORTANT SAFETY PRECAUTIONSIMPORTANT SAFETY PRECAUTIONS
WARNING!: To reduce the risk of fire, electric shock, or injury
When using this self extractor, basic precautions should
always be followed, including the following:
1) DO NOT leave unit when plugged in. Unplug from outlet when not
in use and before servicing.
2) DO NOT allow unit to be used as a toy. Close
attention is necessary when used around or near children.
3) Use only as described in this manual. Use only
manufacturer’s recommended attachments.
4) DO NOT use with damaged cord or plug. If unit is not working
properly because it has been dropped, dropped into water, left
outdoors, or damaged in any way, contact a service center of
Powr-Flite.
5) DO NOT handle plug or appliance with wet hands.
6) DO NOT put any objects into openings. DO NOT use with any
opening blocked: keep free of dust, lint, hair, or anything that may
reduce air flow.
7) Keep hair, loose clothing, fingers, and all parts of body away from
openings and moving parts.
8) DO NOT pick up anything that is smoking or
burning such as cigarettes, matches, or hot ashes.
9) DO NOT use to pick up hazardous chemicals.
10) Turn off all controls before unplugging.
11) Turn unit off immediately if foam or liquid comes from machine
exhaust. Empty & clean out recovery (dirty) tank and use defoamer
to correct the problem.
12) DO NOT use to pick up flammable or combustible liquids such as
gasoline or use in areas where they may be present.
13) DO NOT use where oxygen or anesthetics are used.
14) Replace damaged or worn parts immediately with genuine original
equipment parts to maintain safety.
15) This unit must be connected to a properly grounded outlet only.
See grounding instruction on page 4.
WARNING
To avoid fire, DO NOT
use with a flammable
or combustible liquid
to clean floor.
WARNING
To avoid electric
shock, DO NOT
expose to rain.
Store Indoors.

3
GROUNDING INSTRUCTIONS
DANGER: Improper use of the grounding plug can result in a risk of electric shock.
GROUNDING INSTRUCTIONS
GROUNDING METHODS
This extractor must be properly grounded. If it should malfunction or breakdown, grounding
provides a path of least resistance for electrical current to reduce the risk of electric shock. This
machine is equipped with 1 or 2 pigtail cords having an equipment-grounding conductor and
grounding plug. The pigtails must be inserted into an appropriate 12 gauge extension cord
This unit is for use on a nominal 120 volt circuit and has a
grounded plug that looks like the plug illustrated in (Fig. A).
WARNING!
Improper connection of the equipment-grounding conductor can result in a risk of elec-
tric shock. Check with a qualified electrician or service person if you are in doubt as
to whether the outlet is properly grounded. DO NOT modify the plug provided with the
appliance. If it will not fit the outlet, have a proper outlet installed by a qualified elec-
trician.

4
General instructions for PFX1300 series Extractors
Congratulations on your purchase of a Powr-Flite extractor. You are now equipped to handle any and all commercial carpet
cleaning jobs. Your new extractor is outfitted with a 1750-watt in-line heater (PFX1300H, PFX1300HP & PFX1300HDX models).
The water heats up as it passes through the heater to a high water temperature. To obtain and maintain maximum heat levels
start out with the hottest tap water you can get (120-135 degrees). This will also ensure a faster start up time (60-90 sec.).
Follow these easy step by step instructions to insure proper operating performance.
Shipping and Damage
This equipment is thoroughly inspected, tested, and packaged to provide equipment in good operating condition. It is beyond
our control after the equipment is turned over to a freight carrier. The freight carrier received and signed for the equipment in
good condition. Consequently, it is most important to protect your interest by carefully complying with the following instructions:
Please inspect your cartons for any damage (including concealed damage) that might have occurred during shipment. Any dam-
age is the responsibility of the freight carrier and should be reported to the freight carrier immediately. It is your responsibility to
issue a claim and to receive compensation from the freight carrier for any damage done in transit. Damage of this sort is not
warranted.
Follow these easy step by step instructions to ensure proper operating performance.
1. Fill up the fresh water solution tank with tap water that is
120-135 degrees and approved carpet cleaning chemical
if you are not pre-spraying your chemical on the carpet.
2. Attach two 12 gauge extension cords (NOT INCLUDED)
(one cord for non-heated models) to each of the pigtail
cords located on the lower backside of the unit. The red
pigtail powers the heater while the black pigtail powers
the vacuummotors and pump.
3. Plug each extension cord into a separate and grounded
20 amp wall socket, when this is accomplished the green
indicator light will be lit (on heated models).
4. Attach the hose system to the unit and to your carpet
wand.
5. Turn on the heater and the pump to the "on" position,
(only pump on non-heated models) when the heater is on
the orange indicator light on the switch panel will be lit.
6. With the solution line attached to the wand and the
machine, prime the pump by squeezing the trigger on the
wand releasing the water (hold wand tip over solution
tank to put water back into solution tank). This will
pump water into the heater and get any air out of the
solution line. Let the heater heat up this will take
3 to 5 minutes.
7. Turn vacuum switches to the "on" position and begin
cleaning.
8. Anyone designated to operate this equipment must,
without fail, read and thoroughly understand all
instructions and precautions prior to use.
9. Never use equipment out of doors or in the rain.
10. Never use flammable or explosive materials in
or around this equipment!!!
11. When vacuum tank is full, empty by using drain valve at
front of machine. If a pail is used to empty the vacuum
waste tank, do not use the same pail to fill the solution
tank as this can result in putting dirt and grit into the
solution line that can plug filters, orifices, and generally
degrade the solution line system. (do not reuse solution)
12. To empty solution tank, detach the wand from the end of
the vacuum hose and insert the vacuum hose into the
solution tank. Turn the vacuum switch to "on" position
and transfer solution to vacuum tank and dispose of as
outlined in #12. Clean vacuum stack filter at this time.

5
Maintenance
To receive reliable service from this equipment, regular daily
maintenance is a requirement. Fabric cleaning, both carpet
and upholstery, are very dirty environments for any equipment.
The following recommendations are offered.
1. Keep the equipment clean, both inside and out.
2. Lubricate brass quick disconnects and drain valves with
a quality lubricant such as WD-40.
3. Flush solution systems weekly after daily use preventive
maintenance with clear, clean water. (A white vinegar
solution may also be used). This will counter-act hard
water and alkaline deposits and aid in keeping
orifices clean.
4. Do not allow fluid either in solution or waste tank to sit
overnight. The unit should be emptied and cleaned daily.
5. Clean the strainer in the solution tank, the filter on
vacuum stack in vacuum tank and the lint filter in the
inlet or vacuum tanks daily.
6. Do not use the same receptacle (bucket) to fill solution
tank that is used to remove waste from vacuum tank.
7. When the unit is not in use, leave the vacuum tank lid
open.
8. At the end of each day, run the vacuum for 3 minutes
with lid open and filter off.
Safety Precautions
These precautions are designed with the safety of the operator,
the equipment, and others in mind and must be followed at all
times to avoid serious personal harm and/or death, and dam-
age to the unit.
1. Always use a grounded electrical outlet.
2. Always disconnect electric cable from electrical outlet
before attempting to make any adjustments or repairs.
3. Never use this equipment as a toy.
4. Never use equipment near or around flammable or
explosive materials, fuels, or solvents.
5. Never put flammable materials, fuels, or solvents
into equipment.
6. Never lift the machine by the drain valve.
7. Do not allow the unit to freeze!
8. The equipment was not designed to be used outdoors
or in the rain.
9. Do not operate in standing water.
10. Wear safety equipment and clothing to protect from
extremely hot water.
11. Do not operate equipment under any unsafe condition.

6
12. Do not operate if pigtails, hoses, etc. are cracked, frayed,
leaking, or otherwise in need of repair.
13. Common sense is a powerful force in protecting the
operator, the equipment and others from serious damage
injury and/or death.
Storage of Equipment
1. Store extractor indoors in dry area.
2. Recovery and solution tank should be empty and clean
when the extractor is not in use.
3. Leave the recovery lid and dump valve open to air out the
recovery tank.
4. Do not store in freezing temperature.
5. A small amount of windshield washer fluid available at an
auto supply may be left in the pump and internal solution
line for protection against freezing.
Warnings
1. Do not break off or pull the grounding prong on the plug.
2. Do not attempt repair on a warrantied machine unless
instructions to perform it by an authorized shop are
obtained from the factory.
3. Do not use citrus-based (D-Limonene) cleaners in this
machine.
4. Do not use cleaning chemicals in this machine except
those recommended for steam-type extraction equipment.
The use of any chemicals with abrasive additives voids the
warranty.
5. Do not use any replacement parts except those specified
on the parts list. Performance of the machine
could be affected if substitutions are made.
6. Do not use water in excess of 140° F (62° C) through
the pump system. It could damage the seals and
polyprophene casing of the diaphram pump.
7. Follow maintenance schedule strictly.
8. Failure to comply with the above warnings
instructions will void the warranty.
ONE LAST REMINDER
Read All Instructions, Warning and Cautions Before Using. These guidelines are presented for
your protection and convenience. Please read them carefully, since failure to heed these
precautions could result in discomfort or injury. When using an electrical appliance, basic
safety precautions should always be followed.
WARNING
TO AVOID FIRE, DO NOT USE WITH A FLAMMABLE OR COMBUSTIBLE
LIQUID TO CLEAN FLOOR.

7
MODEL PFX1300 SERIES CARPET EXTRACTOR PARTS
ref# order description
1PF1750 inline heaterfor PFX1300H, HP, HDX
2PX13 gasket, foam, 5.5" od x 1.75"
3PX98 mounting plate, motor/pump/htr
4J1003GC vac hose s-a
5PX129 1/4" npt pipe plug pfx1300
6PX135 pigtail, pfx1300hp
7PX23G 27" solution hose with no ends
8PX99A 36" heat pulse hose w/mnpt&
9PX99B hose, high pressure/temp, 18"x
10 X8284 8-32 x 3/8" phph, type f
11 X8259 washer, flat #8
12 PX42 clamp 5/8"
13 1942 lamb 6474-37 hrn 2st b/b 9.9a
1942-IE motor, vac for PFX1300E
14 SF814 Shurflo pump 100 psi for PFX1300, H
FJ2030X Flo-jet pump 100 psi for PFX1300E
ref# order description
14 PT400 200 psi pumpfor PFX1300HP
PT403 400 psi pump for PFX1300HDX, DX
15 J1003GC hose, flexible, 2" id x 14"
16 PX215 clamp, hose, 2-1/2", ss
17 PX85 fitting, 1/4" mnpt x 3/8" hose
18 PC20 reducer 3/8" to 1/4"
19 PC49 1/4" 90 elbow
20 X8233 bolt, hex, 1/4-20 x 3-1/2"
21 X8289 1/4-20 x 6-1/2" all thread
22 X8213 nut, hex, 1/4-20
23 X8211S 1/4-20 x 1" serrated hex self
24 X8237 nut, 1/4-20, lock, nylon insrt
25 X8287 8-32 x 5/8" phph machine screw
26 X8298 8-32 x 3/4" phph
27 X8256 8-32 keep nut
PFX1300 motor assembly
PFX1300 High Pressure Pump (14)

8
MODEL PFX1300 SERIES CARPET EXTRACTOR PARTS
ref# order description
1PC38 connector double thread female
2PX32 fitting, brass, close nipple,
3PX42 clamp 5/8"
4PX85 fitting, 1/4" mnpt x 3/8" hose
71511A bard 1/2"H-1/2" FPTfor PFX1300HP, HDX, DX
5PX112 pigtail, blk, pfx1300
6PX112R sub, pigtail, red, pfx1300h/hp
7PX10 valve, drain, 1-1/2", model #
8PX103 lid, screw-in
9PX103G gasket, lid
10 PX104 latch assembly
11 PX109 pin, hinge
12 PX88 grommet, 1/4"
13 X8226 1/4-20 x 1-1/4 hex head cap screw
14 X8235A washer, flat
15 X8238 screw, 6-32 x 3/8"
16 X8253 screw, 6-32 x 1"
17 X8257 nut, lock w/nylon insert
18 X8278 8-32 x 1/2" phph, blacj oxide
19 X8282 1/4-20 x 1" hex head cap screw
20 X8283 washer, flat 1/4" s/s
21a PX100 housing, base, black, pfx1300
21b PX101 housing, solution tank, black,
21c PX102 housing, recovery tank, blue,
22 PX105H switch panel
ref# order description
23 PX87 switch, rocker, w/protective cover
24 X8102 neon light with lens
25 PX86 indicator light green
26 PX106A wheel, 10" w/3/4" bore
PX106B wheel, 12 for PFX1300HDX, DX
27 PX107 axle, 3/4" od, pfx1300
28 PX108 bracket, axle, pfx1300
29 PX110G grill, fan, pfx1300
30 PX11 fitting, plastic, elbow, blk.
31 PX11A fitting, plastic, elbow, white
32 PX110 fan, pfx1300hp
33 PX114C cover, terminal block, pfx1300
34 PX117A gauge, 0-300 psi, 2-1/2", abs,
35 PX118A nut, pal, 3/4 " wheel
36 PX119 1/4 nptf x 1/8 nptf reduce cou
37 PX133 sub, harness, switch panel
38 PX137 e clip, 3/4", pfx1300
39 PX14 dump valve gasket 1-1/2"
40 PX14A dump valve gasket 1-1/2" thin
41 PX17 street elbow 45 degree brass
71512A nipple, hex 1/2" for PFX1300HP, HDX, DX
42 PX25 fitting, plastic, bulkhead
43 PX26 caster, 3" dia. wheel
PX65 casters 4"for PFX1300HDX, DX
44 PX30 filter, mesh screen, solution
71495A ball strainer for PFX1300HP, HDX, DX
PFX1300 upper housing assembly

9
MODEL PFX1300 SERIES CARPET EXTRACTOR PARTS
ref# order description
45 PX31 float cage w/heavy ball
46 PX33 float tube, pfx1300/h/hp
47 PX46 nut, lock, die cast, 1-1/2"
48 PX48 fitting, brass, bulkhead, 3/4"
49 772274A washer, 3/4 neoprene
50 PX49 peb plug, pfx1300
51 PX6 1/4 x 1/4 female quick
52 PX98 motor/pump/plt, pfx1300hp
53 X8211S 1/4-20 x 1" serrated hex self
54 X8237 nut, 1/4-20, lock, nylon insrt
ref# order description
55 X8248 nut, 5/16" lock w/nylon insert
56 X8252S 5/16-18 x 1 hex flange lok scr
57 X8256 8-32 keep nut
59 X8271 10-24 nylon insert lock nut
58 X8276 10-24 x 3/4" phph, blk oxide
63 X8284 8-32 x 3/8" phph, type f
62 X8286 8-32 x 1" phph, type f
60 X8287 8-32 x 5/8" phph machine screw
61 X8298 8-32 x 3/4" phph
PFX1300 lower housing assembly

10
Troubleshooting Information
ELECTRICAL SYSTEM
PROBLEM POSSIBLECAUSE SOLUTION
Noelectricalpower.1.Defectivepowercord. 1.Replace
2.Circuitbreakeroffor 2. Turncircuitbreaker
fuseblown. onorreplacefuse.
Unpluganyequipment
usingthesamecircuit.
Switchisturnedon. 1.Faultyelectricalcable. 1.Repairorreplace.
Intermittent power to 2.Defectiveswitches. 2.Replace.
motor(s). 3.Looseterminalordis- 3.Replace.
coloredterminalconnections.
ElectricalShock 1.Equipmentnot 1.Locategrounded
grounded. outlet.
VACUUMSYSTEM
PROBLEM POSSIBLECAUSE SOLUTION
Vacuummotoron 1.Drainvalveopen. 1.Closedrainvalve.
Littleornovacuum Recoverytanklidmust
onwandhead. beclosed.
2.Defective vacuum hose 2.Repairorreplace.
hose.Kinksinvacuum
hose.
Notenoughvacuum 1.Damagedrecovery 1.Replace
poweratthemachine. tanklid.
2.Lintcloggingball - 2. Remove screen.
typeshutoffscreen. Cleanoutfibersand
accumulateddirt.
3. Vacuumhoseconnection 3.Checkforleaks
between stand pipe and aroundclamps(tighten).
vacuum motor (on models Replacedamaged
with 2 vac motors, the hose(s).
vacuum hose connection
in between.
4. Vacuummotor 4.Checkairflowby
exhaustblocked. removinghosefrom
machineandfeelthe
exhaustunderthe
machine. Remove
obstruction.
VACUUMSYSTEM
PROBLEM POSSIBLECAUSE SOLUTION
Motorrunningandno 1.Faultyvacuummotor.1.Replace.
vacuumatall.
Noexhaustfromthe 2. Watershutoffclosed. 2.Cleanwatershutoff
blowport. screen.
Prematureclosingof 1.Dirtyorcloggedshut- 1.Removeandclean
balltypeshutoff. offfilterscreen. screen.
Balltypeshutoff 2.Ballcoatedwith 2.Removeandrinse
failingtoreleaseafter detergentorother ballwithcleanwater.
recoverytank is drained. foreignmaterial.
2.Screenslightlyoutof 3. Bendscreenby
round. squeezingslightlyby
handuntilthereisan
obvious space between
balland inside of screen.
Foam/dirtysolution 1.Foamfromcarpetby- 1.Useadditional
comingoutofvacuum passingwatershutoff. defoamer.
exhaustport. 2.Elbowinvacuumtank 2.Theelbowshouldbe
isnotpositioned pointeddirectlyatthe
correctly.sidewallofthetank
awayfromtheballtype
shutoff.
SOLUTIONSYSTEM
PROBLEM POSSIBLECAUSE SOLUTION
Pumpmotoron – 1. Clogged orfaulty 1.Checkintakeon
nospraythroughjets. solutioncontrolvalve. valve and removelint
or other foreign
material.
2.Cloggedorfaulty 2.Depressplungeron
quickdisconnecton solutionhoseagainst
housing. insidewallofsolution
tank.Ifsolutionisflow-
ing at thispoint,the
system is O.K.Ifno
solution flows, check the
quick disconnect for lint
and other foreign matter.
3.Puncturedpump 3.Replacewith
diaphragm. diaphragmrepairkit.
PROBLEM POSSIBLECAUSE SOLUTION
Unevensprayfrom 1.Cloggedstrainerin 1.Unscrewstrainer
jet.Sprayweakor solutiontank. andremovelintand
uneven. any other foreign
material from screen.
2.Cloggedjet. 2.Removeandclean.
Leakingorstuck 1.Foreignmaterialin 1.Removebrasshex
solutionvalve. valve. plug,cleanvalveand
replace.
2.Loosebrasshexnut. 2.Resealhex and plug.
3. Valvewornorseals 3.Replacewornparts
worn. withsolutionvalve
repairkit.
Pumpmotor 1. Loose wiring 1. Tighten wiring
not working. 2. Defective pump 2. Replace with new
pressure switch pressure switch assembly
3. Motor burnout 3. Replace pump motor
Pumppressurelow 1.Cloggedscreenson 1.Unscrewstrainer
strainerin solution tank
.removelintandany
otherforeignmaterial
fromscreen.
2.Puncturedpump 2.Replacewith
diaphragm. diaphragmrepairkit.
3.Defectiverectifieror 3.Replace.
motor.
Pumppressurevaries. 1. Worncarbonbrushes. 1.Replacebrushes.
2.Defectivepump 2.Replace.
pressurecontrolswitch.

A Tacony Company
3101 Wichita Court • Ft. Worth, TX 76140-1710
WARRANTY
The manufacturer warrants to the original purchaser that products manufactured are free from defects of
workmanship and material, provided such goods are installed, operated and maintained in accordance with
written manuals or other instructions for a period of 5 years from date of purchase on housings and frame, 3
years on heater, 1 year on pump, vac motor, and parts and workmanship. In case you as our customer, meet
any trouble with your machine, contact your Powr-Flite representative who will be happy to be of service to
you and will take care of the warranty settlement.
NOTE: Alterations and changes made to the machine without written approval of the
manufacturer and use of unapproved spare parts will not be covered by warranty.