PQ Plus UMD 703 Instruction manual

• •
Quick-Start Anleitung
Quick-Start Manual
UMD 703
Deutsch / English

PQ Plus – UMD 703Quick-Start Anleitung
2
DE
Inhaltsverzeichnis
Installation................................................................................................4
Montage .......................................................................................................4
Spannungsversorgung .................................................................................4
Spannungsmessung ....................................................................................5
Stromwandler anschließen ..........................................................................6
RS485-Schnittstelle .....................................................................................6
Inbetriebnahme......................................................................................6
Werksseitige Kommunikationseinstellungen ................................................6
Verbindung mit einem PC herstellen ............................................................7
Stromwandler einstellen ...............................................................................8
Kommunikationsparameter einstellen ..........................................................8
Anschluss und Einstellungen kontrollieren ..................................................9
Technische Daten................................................................................10

PQ Plus – UMD 703
3
EN
Quick-Start Anleitung
Table of Contents
Installation............................................................................................... 11
Mounting..................................................................................................... 11
Voltage supply ............................................................................................ 11
Voltage measurement.................................................................................12
Connecting a current transformer...............................................................13
RS485 interface..........................................................................................13
Commissioning...................................................................................... 13
Factory communication settings.................................................................13
Connecting to a PC ....................................................................................14
Setting the current transformer...................................................................15
Setting communication parameters............................................................15
Checking the connection and settings........................................................16
Technical data........................................................................................17

Quick-Start Anleitung
4
DE
Installation
Montage
Das UMD 703 ist für eine Montage auf der DIN-Hutschiene vorgesehen.
S1
I1 I2 I3 RS-485
+A-BG2S2S2S 1S1S
Voltage Inputs
NL1 L2 L3
300 V
CAT III
62.2
11.0
45.0
67.5
89.7
98.0
53.6
Spannungsversorgung
Das UMD 703 versorgt sich aus der Messspannung und benötigt folgende
Versorgungsspannung:
100 ... 310 VAC
100 ... 330 VDC
Die Anschlüsse für die Messspannung benden sich unten am UMD
und sind mit L1, L2, L3 und dem gemeinsamen Neutralleiteranschluss N
beschriftet. Die Versorgungsspannung ist intern vom Anschluss der Mess-
spannung (L1 und N) gebrückt. Für die Absicherung der Spannungsversor-
gung wird ein 1 A Leitungsschutzschalter empfohlen.

Quick-Start Anleitung PQ Plus – UMD 703
5
DE
Spannungsmessung
Das UMD 703 verfügt über 3 Spannungseingänge welche sowohl für eine
direkte als auch für eine Wandlermessung geeignet sind. Die Phasenspan-
nungen werden über die Klemmen L1, L2, L3 und den gemeinsamen Neut-
ralleiteranschluss N gemessen.
Es wird empfohlen, die Spannungspfade mit einem 1 A Leitungsschutz-
schalter abzusichern.
L1
L2
L3
N/PEN
T0,5A
S1
I1 I2 I3 RS-485
+A-BG2S2S2S 1S1S
Voltage Inputs
NL1 L2 L3
300 V
CAT III
X/333mV
S1 S2
S1 S2
S1 S2

Quick-Start Anleitung
6
DE
Stromwandler anschließen
Die Universalmessgeräte sind nicht für eine direkte Strommessung ausge-
legt. Die Anschlüsse der benötigten Stromwandler benden sich oben am
Gerät und sind folgendermaßen beschriftet:
•I1; S1 und S2 für den Stromwandler auf Phase 1,
•I2; S1 und S2 für den Stromwandler auf Phase 2,
•I3; S1 und S2 für den Stromwandler auf Phase 3;
Die Stromwandleranschlussklemmen sind für Sekundärsignale von 333 mV
ausgelegt.
RS485-Schnittstelle
Das UMD 703S ist mit einer RS485-Schnittstelle ausgestattet, die über das
Modbus RTU-Protokoll kommuniziert. Die Anschlüsse benden sich oben am
Gerät und sind mit „A+“, „B-“ und „G“ beschriftet.
Inbetriebnahme
Werksseitige Kommunikationseinstellungen
Das UMD 703S wird standardmäßig mit der Geräteadresse 1 und einer
Baudrate von 9600 Baud ausgeliefert.

Quick-Start Anleitung PQ Plus – UMD 703
7
DE
Verbindung mit einem PC herstellen
Um das UMD 703S mit einem PC zu verbinden, können Sie entweder ei-
nen Schnittstellenkonverter (z.B. RS485 auf USB) oder ein Mastergerät als
Gateway verwenden.
Konverter: Für diese Verbindung muss der dazugehörige USB-Treiber des
Schnittstellenkonverters auf dem PC installiert sein.
Gateway: Wenn Sie sich per LAN-Kabel mit einem Mastergerät verbinden
möchten, müssen Sie entweder die IP-Adresse des Gerätes auf Ihr Netz,
oder die IP-Adresse Ihres PC´s anpassen. Alle PQ Plus Universalmessge-
räte mit Ethernetschnittstelle werden mit der IP: 10.0.0.1 ausgeliefert.
•Öffnen Sie die ENVIS.Daq und wählen für den Schnittstellenkonverter den
Punkt „COM“ und für das Mastergerät den Punkt „TCP“. (Für die Verbin-
dung an einem Mastergerät muss in diesem das Gateway aktiviert sein.)
•Öffnen Sie das Dropdown-Menü und wählen die COM-Schnittstelle aus
oder tragen die IP-Adresse des Mastergerätes und den dazugehörigen Port
(Standard: 4001) in die dafür vorgesehenen Felder ein.
•Mit einem Klick auf „Verbinden“ wird die Verbindung zum UMD hergestellt.
Hier können Sie alle weiteren Einstellungen des Gerätes vornehmen.

Quick-Start Anleitung
8
DE
Kommunikationsparameter einstellen
Unter dem Punkt „Kommunikation“ können alle Kommunikationsparameter
des UMD’s eingestellt werden.
Stromwandler einstellen
Nachdem Sie in der Software mit dem Gerät verbunden sind,
wählen Sie den Punkt .
Unter dem Register „Install“ kann die Messung konguriert werden:
Nennwerte, Netzform, Wandlerverhältnisse, …

Quick-Start Anleitung PQ Plus – UMD 703
9
DE
Anschluss und Einstellungen kontrollieren
Der Anschluss und die Einstellungen des Messgerätes können nun
über die LiveDaten in der ENVIS.Daq kontrolliert werden.
•Anhand der Stromanzeige kann die Plausibilität überprüft werden. Falls
Sie die Stromstärke nicht kennen, wird empfohlen die Stromstärke mit
einer Stromzange zu vergleichen.
•Bei der Anzeige der einzelnen Wirkleistungen wird Bezug ohne Vorzei-
chen und Lieferung mit negativem Vorzeichen angezeigt. So kann der
richtige Einbau und Anschluss der Stromwandler überprüft werden.
•Über das Zeigerdiagramm kann das Drehfeld und die Zuordnung der
Strom- und Spannungspfade kontrolliert werden. Achten Sie hierbei auf
die Phasenverschiebung von Strom und Spannung.

PQ Plus – UMD 703Quick-Start Anleitung
10
DE
Technische Daten
Spannungsversorgung Aus Messspannung (L1) 100 ... 310 VAC;
100 ... 330 VDC
Spannungsmessung 8 ... 355 VLN; 14 … 615 VLL
Frequenz 40 … 70 Hz
Abtastrate 6,4 kHz
Leistungsaufnahme 7 VA / 2 W
Umgebungstemperatur TBetrieb -25 ... 70 °C
Schutzart Front / Rückseite IP40 / IP20
EMV Klasse A: Industriebereich nach IEC 61326-1
Überspannungskategorie 230 V: CAT III / 300 V; 24 V: CAT IV / 300 V
Überlast (permanent) U: 1355 VLN | I: 666 mVAC
Überlast (1s) U: 2140 VLN | I: 3,33 VAC
Mechanische Daten
Montage 35 mm DIN Schiene
Maße BxHxT 54 x 90 x 61 mm
Gewicht Ca. 130 g
Schnittstellen
RS485 2400 … 1382400 Baud
Protokolle Modbus RTU

PQ Plus – UMD 703
11
EN
Quick-Start Anleitung
Installation
Mounting
The UMD 703 is intended for mounting on the DIN rail.
S1
I1 I2 I3 RS-485
+A-BG2S2S2S 1S1S
Voltage Inputs
NL1 L2 L3
300 V
CAT III
62.2
11.0
45.0
67.5
89.7
98.0
53.6
Voltage supply
The UMD 703 is supplied from the measurement voltage. It requires the
following supply voltage:
100 ... 310 VAC
100 ... 330 VDC
The connections for the measurement voltage are located at the bottom of
the UMD and labelled L1, L2, L3, and the shared neutral conductor connec-
tion N. The supply voltage is internally bridged from the connection of the
measurement voltage (L1 and N). It is recommended to protect the voltage
supply with a 1 A circuit breaker.

PQ Plus – UMD 703Quick-Start Manual
12
EN
Voltage measurement
The UMD 703 has 3 voltage inputs that are suitable for both direct and cur-
rent transformer measurements. The phase voltages are measured via the
terminals L1, L2, L3 and the joint neutral conductor connection N.
It is recommended to secure the voltage paths with a 1 A circuit breaker.
L1
L2
L3
N/PEN
T0,5A
S1
I1 I2 I3 RS-485
+A-BG2S2S2S 1S1S
Voltage Inputs
NL1 L2 L3
300 V
CAT III
X/333mV
S1 S2
S1 S2
S1 S2

PQ Plus – UMD 703
13
EN
Connecting a current transformer
The universal measurement devices are not designed for direct current
measurement. The connections of the required current transformers are
located at the top of the device and labelled as follows:
•I1; S1, and S2 for the current transformer on phase 1,
•I2; S1, and S2 for the current transformer on phase 2,
•I3; S1, and S2 for the current transformer on phase 3;
The current transformer connection terminals are designed for secondary
signals of 333 mV.
RS485 interface
The UMD 703S is equipped with an RS485 interface that communicates via
the Modbus RTU protocol. The connections are located on the top of the
device and labelled "A+", "B-", and "G".
Commissioning
Factory communication settings
The UMD 703S is delivered by default with the device address 1 and a
baud rate of 9600 Baud.

PQ Plus – UMD 703Quick-Start Manual
14
EN
Connecting to a PC
You can either use an interface converter (e.g., RS485 to USB) or a master
device as gateway to connect the UMD 703S to a PC.
Converter: The associated USB driver of the interface converter must be
installed on the PC for this.
Gateway: If you want to connect to a master device by LAN cable, you
need to either adjust your device's IP address to your network or the IP ad-
dress of your PC. All PQ Plus universal measurement devices with Ethernet
interface are delivered with the IP: 10.0.0.1.
•Open the ENVIS.Daq and select the item "COM" for the interface convert-
er and the item "TCP" for the master device. (The gateway must be
enabled at the master device to connect to it.)
•Open the drop-down menu and select the COM interface or enter the
IP address of the master device and the associated port (default: 4001)
the elds provided for this.
•Clicking "Connect" establishes a connection to the UMD. You can make
all further settings of the device here.

PQ Plus – UMD 703
15
EN
Setting communication parameters
All communication parameters of the UMD can be set under the item "Com-
munication".
Setting the current transformer
Once you have connected to the device in the software,
select the item .
You can congure the measurement under the tab "Install":
Nominal values, network conguration, current transformer ratios, …

PQ Plus – UMD 703Quick-Start Manual
16
EN
Checking the connection and settings
The connection and the settings of the universal measurement device
can now be reviewed via the Act Data in the ENVIS.Daq.
•The display of the currents can be used to review plausibility. If you do
not know the current, we recommend comparing the current with a cur-
rent clamp.
•When displaying the individual active powers, consumption is displayed
without a prex and supply with a negative prex. This permits verication
of the correct installation and connection of the current transformers.
•The pointer diagram can be used to check the rotating eld and assign-
ment of the current and voltage paths. Observe the phase shift of current
and voltage for this.

PQ Plus – UMD 703
17
EN
Technical data
Voltage supply From measurement voltage (L1) 100 ... 310 VAC;
100 ... 330 VDC
Voltage measurement 8 ... 355 VLN; 14 … 615 VLL
Frequency 40 … 70 Hz
Sampling rate 6.4 kHz
Power consumption 7 VA / 2 W
Ambient temperature Toperation -25 ... 70 °C
Protection type front / rear IP40 / IP20
EMC Class A: Industrial area according to
IEC 61326-1
Overvoltage category 230 V: CAT III / 300 V; 24 V: CAT IV / 300 V
Overload (permanent) U: 1355 VLN | I: 666 mVAC
Overload (1s) U: 2140 VLN | I: 3.33 VAC
Mechanical data
Mounting 35 mm DIN rail
Dimensions WxHxD 54 x 90 x 61 mm
Weight Approx. 130 g
Interfaces
RS485 2400 … 1382400 baud
Protocols Modbus RTU

PQ Plus – UMD 703Quick-Start Manual
18
EN

PQ Plus – UMD 703
19
EN

PQ Plus GmbH
Hagenauer Straße 6
D-91094 Langensendelbach
Tel. / Phone: (+49) 9133-60640-0
Fax: (+49) 9133-60640-100
Email: [email protected]
Internet: http://www.pq-plus.de
Geschäftsführung / Managing directors:
Anna Beyer, Daniel Fierus-Beyer
Umsatzsteuer Identikationsnummer / VAT ID:
DE 301 767 284
Weitere Informationen und den aktuellen Katalog nden Sie bei
uns im Internet.
For further information and the current catalogue, see our website.
https://www.pq-plus.de
Stand / As of: 2024.01
Technische Änderungen vorbehalten.
Technical changes reserved.
Table of contents
Languages:
Other PQ Plus Measuring Instrument manuals

PQ Plus
PQ Plus UMD 705 Instruction manual

PQ Plus
PQ Plus UMD 98 Instruction manual

PQ Plus
PQ Plus CMD 68-54 Instruction manual

PQ Plus
PQ Plus UMD 97 Instruction manual

PQ Plus
PQ Plus UMD 807 E User manual

PQ Plus
PQ Plus UMD 701 User manual

PQ Plus
PQ Plus UMD 96 User manual

PQ Plus
PQ Plus MMU 3 Instruction manual

PQ Plus
PQ Plus MMD 98 Instruction manual

PQ Plus
PQ Plus MMI 12RCM Instruction manual