Precision Digital Corporation PD686 User manual

Precision Digital corPoration
89 October Hill Rd • Holliston MA 01746 USA • Tel [phone] • Fax [phone]
PD686 FM APPROVED & CSA CERTIFIED LOOP-POWERED METER
Intrinsic Safety Barrier Connections
1155_L
LIM686-2_D 09/08
SECTION AGENCY DESCRIPTION
1.0 General Notes
2.0 FM/CSA Conduit Installation Instructions
3.0 FM Single or Dual Channel Positive Polarity
Intrinsic Safety Barrier
4.0 CSA Single or Dual Channel Instrinsic Safety
Barrier Entity Installation
Note: FM AND CSA CoNtRoLLeD DoCUMeNt.
No CHANGeS WItHoUt PRIoR FM AND CSA APPRoVAL.
1.0 GENERAL NOTES
1.1 For Class II, Class III (Division 1 and 2) and NEMA/CSA
type 4X installations, use conduit hub which is listed/certified
for the environment in which the indicator is installed.
1.2 For Class II and III (Division 1 and 2) installations, field wiring
must enter the enclosure through a listed/certified dust-tight
conduit seal.
1.3 Control room equipment must not use or generate more than
250 VRMS or VDC.
1.4 US installations must be in accordance with ANSI/ISA
RP12.06.01 “Installation of Intrinsically Safe Systems for
Hazardous (Classified) Locations” and the National Electrical
Code (ANSI/NFPA 70). Canadian installations must be in
accordance with the Canadian Electrical Code, Part 1.
1.5 Hazardous location installation instructions for associated
apparatus (barrier) must also be followed when installing this
equipment.
1.6 For safe installation of a FM Approved/CSA Certified
transmitter in series with PD686 loop indicator, the hazardous
location installation instructions for the transmitter, PD686 loop
indicator, and associated apparatus (barrier) must be compatible.
1.7 PD686 indicator does not add capacitance or inductance to loop
under normal or fault conditions.
1.8
Substitution of components may impair hazardous location
safety.
2.0 PD686 CONDUIT INSTALLATION INSTRUCTIONS
2.1 Remove the Display from the enclosure and connect ½"
conduit fittings to the hole provided. For enclosures without a
pre-drilled hole, the installer must make a hole in accordance
with the instructions for the particular conduit fitting being
installed.
2.2 Use only UL/CSA conduit hubs that are specified to maintain
NEMA 4X and Class II / Class III ratings.
2.3 Conduit hubs must be connected to the conduit prior to being
connected to the enclosure.
2.4 Enclosure must be mounted using the mounting holes
located in the base external to the equipment cavity.
www.predig.com
Conduit Hole
LONG SIDE VIEW
2.755" (70 mm)
0.790"
(20 mm)
0.750"
(19 mm)
2.56"
(65 mm)
TYPICAL HOLE LOCATION
3.0 PD686 FM INSTALLATION WIRING DIAGRAM
Using single or dual channel intrinsic safety barrier
S- S+
+
-
FM Entity Approved
positive polarity single
or dual-channel intrinsic
safety barrier used in an
approved configuration.
<1 ohm to Ground
Class I, Div 1, 2, Groups ABCD
Class II, Div 1, Groups EFG
Class II, Div 2, Groups FG
Class III,
Div 1, 2
Class 1,
Zone 0,
Group IIC
HAZARDOUS AREA NON-HAZARDOUS AREA
FM ENTITY APPROVED TRANSMITTER INSTALLED PER TRANSMITTER
MANUFACTURER'S HAZARDOUS LOCATION INSTALLATION DRAWING
PD686 ENTITY PARAMETERS:
U
i
: 30 V; I
i
: 175 mA; C
i
: 0; Li: 0; Pi: 1.3 W
I.S.GROUND
PD686
Application Notes:
3.1 Ui > U
o
of single channel barrier or V
t
of dual channel barrier
3.2 Ii
> I
o
of single channel barrier or I
t
of dual channel barrier
3.3 Liplus interconnecting wiring < Loof single or dual channel barrier
3.4 Ciplus interconnecting wiring < Coof single or dual channel barrier
3.5 It is not necessary to use intrinsic safety barriers when installing the
PD686 in Class I,II,III, Division 2, Groups ABCDFG, maximum input
voltage = 30 VDC.
4.0 PD686-CSA INSTALLATION WIRING DIAGRAM
Using single or dual channel intrinsic safety
barrier-entity installation
S- S+
+
-
CSA Entity Certified
positive polarity single
or dual-channel intrinsic
safety barrier used in an
approved configuration.
<1 ohm to Ground
Class I, Div 1, 2, Groups ABCD
Class II, Div 1, Groups EFG
Class II, Div 2, Groups FG
Class III,
Div 1, 2
HAZARDOUS AREA NON-HAZARDOUS AREA
CSA ENTITY CERTIFIED TRANSMITTER INSTALLED PER TRANSMITTER
MANUFACTURER'S HAZARDOUS LOCATION INSTALLATION DRAWING
PD686-CSA ENTITY PARAMETERS:
Vmax
: 30 V; I
max
: 175 mA; C
i
: 0; L
i : 0; P i
: 1.3 W
I.S.GROUND
PD686-CSA
Application Notes:
4.1 Barrier parameters must meet the following requirements:
V
oc or Uo ≤ Vmax or Ui
I
sc or Io ≤ Imax or Ii
C
aor Co ≥ C
i+ Ccable
L
aor Lo≥ Li + Lcable
Po< Pi
4.2 For CSA Certification, barrier and transmitter must be CSA Certified
with Entity Parameters and must be connected per manufacturer’s
instructions.
4.3 It is not necessary to use intrinsic safety barriers when installing the
PD686-CSA in Class I,II,III, Division 2, Groups ABCDFG, maximum
input voltage = 30 VDC.
Order from:
C A Briggs Company
622 Mary Street; Suite 101
Warminster, PA 18974
Phone: [phone]
Fax: [phone]
[email protected] - www.cabriggs.com