Precision Digital Corporation PROVU PD6363 User manual

PROVU™PD6363 Dual Pulse Input Rate/Totalizer
Instruction Manual
PRECISION DIGITAL CORPORATION
233 South Street • Hopkinton MA 01748 USA
Tel [phone] • Fax [phone]
www.predig.com
•1/8 DIN Digital Panel Flow Rate/Totalizers with NEMA 4X, IP65 Front
•Dual Pulse, Open Collector, NPN, PNP, TTL, Switch Contact, Sine Wave (Coil), Square Wave Inputs
•Rate, Total, and Grand Total for Each Input Channel
•Dual-Line 6-Digit Display, 0.6" (15 mm)& 0.46" (12 mm)
•Isolated 5, 10 or 24 VDC Flowmeter Power Supply
•2 or 4 Relays + Isolated 4-20 mA OutputOptions
•Free PC-Based, On-Board, MeterView Pro USB Programming Software
•No Assembly Required
•Gate Function for Display of Slow Pulse Rates
•K-Factor, Internal Scaling, orExternal Calibration
•Optional SunBright Display Models for Outdoor Applications
•Operating Temperature Range: -40 to 65°C (-40 to 149°F)
•UL & C-UL Listed. E160849; 508 Industrial Control Equipment
•Input Power Options: 85-265 VAC / 90-265 VDC or 12-24 VDC / 12-24 VAC
•Programmable Display, Function Keys & Digital Input
•External 4-Relay, Dual Analog Output, & Digital I/O Expansion Modules
•RS-232 & RS-485 Serial Communication Options with Modbus RTU
•Password Protection
•WideAssortmentofNEMA 4XEnclosures for up to Ten Meters
•Light / Horn & Reset Button Accessory
•Control Station Accessory for Remote Operation
•3-Year Warranty
MeterView Pro
USB Install

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
2
Disclaimer
The information contained in this document is
subject to change without notice. Precision Digital
makes no representations or warranties with
respect to the contents hereof and specifically
disclaims any implied warranties of
merchantability or fitness for a particular purpose.
See Warranty Information and Terms &
Conditions on www.predig.com for complete
details.
•Read complete instructions prior to installation
and operation of the meter.
•Risk of electric shock or personal injury.
•This product is not recommended for life support
applications or applications where malfunctioning
could result in personal injury or property loss.
Anyone using this product for such applications
does so at his/her own risk. Precision Digital
Corporation shall not be held liable for damages
resulting from such improper use.
WARNING
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Limited Warranty
Precision Digital Corporation warrants this
product against defects in material or
workmanship for the specified period under
“Specifications” from the date of shipment from
the factory. Precision Digital’s liability under this
limited warranty shall not exceed the purchase
value, repair, or replacement of the defective unit.
See Warranty Information and Terms &
Conditions on www.predig.com for complete
details.
Registered Trademarks
All trademarks mentioned in this document are
the property of their respective owners.
© 2021 Precision Digital Corporation.
All rights reserved.
FREE MeterView Pro
Programming Software
The meter can be powered from the Micro USB connection.
When using the Micro USB connection, DO NOT apply AC or DC
power to the meter.
The easiest and quickest way to program your PROVU
meter is to use the FREE MeterView Pro
programming software. This software is loaded into
the meter and connects and installs directly to your
PC with a USB cable. We recommend that the first
thing you do after taking the meter out of the box is
connect the PROVUto your PC with the provided USB
cable –do not use a different cable. DO NOT apply
AC or DC power to the meter while your PC is
connected to the meter as it will disrupt the USB
connection. You don’t even have to apply an input
signal.
MeterView Pro programming software is intuitive, and
most customers can get their meter programmed as
they like without even looking in the manual.
Watch MeterView Pro Software Video at
www.predig.com/meterviewpro
In addition to programming, the software may be used
for:
•Monitoring
•Datalogging using your PC
•Generating and saving programming files for
later use
Once your meter is programmed the way you want it,
you can wire it up for your application per the
instructions in this manual and install it. If you find that
you need to make adjustments to the programming
after the meter is installed, you can use the front
panel buttons and the instructions in this manual to do
so.

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
3
Table of Contents
Introduction..........................................................................................................6
Ordering Information...........................................................................................6
Specifications.......................................................................................................9
General.............................................................................................................9
Dual Pulse Inputs ..........................................................................................10
Dual Rate/Totalizer........................................................................................11
Relays.............................................................................................................11
Isolated 4-20 mA Transmitter Output ..........................................................12
USB Connection............................................................................................12
On-Board Digital Input (F4)...........................................................................12
Modbus®RTU Serial Communications........................................................12
MeterView Pro................................................................................................12
Compliance Information....................................................................................13
Safety..............................................................................................................13
Electromagnetic Compatibility.....................................................................13
Safety Information .............................................................................................13
Installation..........................................................................................................13
Unpacking......................................................................................................13
Panel Mounting Instructions ........................................................................14
Mounting Dimensions..................................................................................14
Installation Overview.....................................................................................15
MeterView Pro Software................................................................................15
MeterView Pro Installation...........................................................................15
Flowmeter Supply Voltage Selection (P+, P-) .................................................16
Connections...................................................................................................16
Connectors Labeling ...................................................................................16
Power Connections.....................................................................................17
Signal Connections .....................................................................................17
Configure Input Type and Level Switches..................................................17
Modbus RTU Serial Communications.........................................................18
Relay Connections......................................................................................18
Switching Inductive Loads...........................................................................18
F4 Digital Input Connections.......................................................................19
4-20 mA Output Connections......................................................................19
Analog Output Transmitter Power Supply...................................................19
External Relay, Analog Output, & Digital I/O Connections..........................20
Remote Operation of Meter.........................................................................20
Interlock Relay Feature...............................................................................20
Setup and Programming...................................................................................21
Front Panel Buttons and Status LED Indicators ........................................21
Display Functions & Messages....................................................................22
Main Menu......................................................................................................25
Setting Numeric Values ................................................................................25
Setting Up the Meter (setup)........................................................................26
Setting the Input Signal (Input)..................................................................27
Setting the Totalizer Features (total) ...................................................27
Setting the Dual-Input Mode (nmode)......................................................27
Setting the Rate, Total, & Grand Total Units/Tags (units).........................29
Setting the Decimal Point (dEc pt).............................................................29
Programming the Rate/Totalizer (prog)......................................................30
Input Calibration Method (InCAL) ...........................................................30
K-Factor Calibration (Fact-A, Fact-b)...................................................30
Scaling the Meter without a Signal Source (SCAL-A, SCAL-B)................30
Scaling the Meter for Channel A (SCal-A)..............................................31
Error Message (Error)...........................................................................31
Calibrating the Meter with External Source (CAL-A, CAL-B)...................32
Total & Grand Total Setup (tsetup).......................................................32
Total & Grand Total Reset (treset).......................................................32
Setting the Display Parameters & Intensity (dsplay)..................................33
Display Intensity (d-Inty)...........................................................................33

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
4
Setting the Relay Operation (relay)...........................................................34
Setting the Relay Assignment (asSign) .................................................34
Setting the Relay Action (Act)................................................................34
Programming Set and Reset Points........................................................35
Setting Fail-Safe Operation.....................................................................35
Programming Time Delay.......................................................................35
Relay Action for Loss of 4-20 mA Input (Loop Break).............................35
Relay and Alarm Operation Diagrams.........................................................35
High Alarm Operation (Set >Reset)..............................................................35
Low Alarm Operation (Set < Reset)............................................................36
High Alarm with Fail-Safe Operation (Set > Reset).....................................36
Low Alarm with Fail-Safe Operation (Set < Reset) .....................................36
Time Delay Operation .................................................................................36
Pump Alternation Control Operation ...........................................................37
Relay Sampling Operation ..........................................................................37
Relay Operation Details................................................................................38
Overview .....................................................................................................38
Relays Auto Initialization.............................................................................38
Fail-Safe Operation.....................................................................................38
Front Panel LEDs........................................................................................38
Latching and Non-Latching Relay Operation ..............................................38
Non-Latching Relay (Auto) .........................................................................39
Non-Latching Relay with Manual Reset (A-nman).......................................39
Latching Relay (LatcH)...............................................................................39
Latching Relay with Clear (Lt-Clr)............................................................39
Acknowledging Relays................................................................................39
Setting Up the Interlock Relay (Force On) Feature.....................................40
Scaling the 4-20 mA Analog Output (Aout).................................................40
Reset Menu (reset).......................................................................................40
Manual Control Menu (Contrl).....................................................................40
Setting Up the Password (pass)...................................................................41
Protecting or Locking the Meter Functions..................................................41
Total Reset Password & Non-Resettable Total...........................................41
Making Changes to a Password Protected Meter.......................................41
Disabling Password Protection....................................................................41
Advanced Features Menu.............................................................................42
Advanced Features Menu & Display Messages..........................................42
Gate Function (Gate) ..................................................................................43
Contact De-Bounce Filter (FiLter).............................................................44
Rounding Feature (round)..........................................................................44
Modbus RTU Serial Communications (serial)..........................................44
Select Menu (SElect).................................................................................45
Input Signal Conditioning (Functn).............................................................45
Multi-Point Linearization (Linear)..........................................................45
Math Function (nmath)................................................................................46
Math Constants (Const)..............................................................................46
Low-Flow Cutoff (CutofF)...........................................................................46
Totalizer Count Up/Down (Count)...............................................................47
Analog Output Programming (AoutPr) .......................................................47
Programmable Function Keys User Menu (user).......................................48
Meter Operation .................................................................................................50
Front Panel Buttons Operation....................................................................50
Function Keys Operation..............................................................................50
F4 Operation ..................................................................................................50
Maximum/Minimum Readings......................................................................50
Troubleshooting.................................................................................................51
Diagnostics Menu (diag) ..............................................................................51
Testing the Display LEDs............................................................................51
Determining Software Version.....................................................................51
Reset Meter to Factory Defaults...................................................................51
Factory Defaults & User Settings................................................................52
Troubleshooting Tips....................................................................................54
EU Declaration of Conformity...........................................................................55

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
5
Table of Figures
Figure 1. 1/8 DIN Panel Cutout Dimensions....................................................14
Figure 2. Panel Mounting Details .....................................................................14
Figure 3. Meter Dimensions - Side View..........................................................14
Figure 4. Meter Dimensions - Top View...........................................................14
Figure 5. Transmitter Supply Voltage Selection.............................................16
Figure 6. PD6363-##0 Connectors Label .........................................................16
Figure 7. PD6363-##2 Connectors Label .........................................................16
Figure 8. PD6363-##3 Connectors Label .........................................................16
Figure 9. PD6363-##4 Connectors Label .........................................................16
Figure 10. PD6363-##5 Connectors Label .......................................................16
Figure 11. PD6363-##7 Connectors Label .......................................................16
Figure 12. Power Connections .........................................................................17
Figure 13. Flowmeters Powered by Internal Power Supply...........................17
Figure 14. Flowmeters Powered by External Supply......................................17
Figure 15. Self-Powered Magnetic Pickup Coil Flowmeter............................17
Figure 16. NPN open Collector Input ...............................................................17
Figure 17. PNP Sensor Powered by Internal Supply......................................17
Figure 18. Switch Input Connections...............................................................17
Figure 19. Relay Connections...........................................................................18
Figure 20. AC and DC Loads Protection..........................................................18
Figure 21. Low Voltage DC Loads Protection.................................................18
Figure 22. F4 Digital Input Connections..........................................................19
Figure 23. 4-20 mA Output Connections .........................................................19
Figure 24. Analog Output Supply Powering Other Devices...........................19
Figure 25. Expansion Module & DIN Rail Mounting Kit..................................20
Figure 26. External Relays Module Connections............................................20
Figure 27. Digital I/O Module Connections......................................................20
Figure 28. Dual 4-20 mA Output Module Connections.......................................20
Figure 29. Meter to Control Station Connections...........................................20
Figure 30. Interlock Connections.....................................................................20
Figure 31. Dual Input Mode (ud AB)..................................................................27
Figure 32. Dual Input Mode (ud AI)..................................................................27
Figure 33. Dual Input Mode (ud BI)..................................................................28
Figure 34. Dual Input Mode (quad 1)................................................................28
Figure 35. Dual Input Mode (quad 2)................................................................28
Figure 36. Dual Input Mode (quad 4)................................................................28

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
6
Introduction
The PROVUPD6363 is a multipurpose, easy to use
digital dual pulse input rate/totalizer ideal for flow rate,
total, and flow control applications. Its superluminous
LED digits make it easily readable in smoke, dust,
fog, and, with the optional SunBright display, even
direct sunlight.
It accepts two pulse (e.g. 40 mVp-p to 8 Vp-p), square
wave (0-5 V, 0-12 V, or 0-24 V), open collector, NPN,
PNP, TTL or switch contact signals. Various math
functions may be applied to the rate, total, or grand
totals of the two channels; including addition,
difference, average, minimum, maximum, draw, ratio
and more.
The displays, relays, and the analog output may be
assigned to the rate, total, or grand total of input
channels A or B; or math result channel C. Three of
the front panel buttons can be custom-programmed
for a specific operation.
The basic model includes an isolated 24 VDC
transmitter power supply that can be used to power
the input transmitters or other devices. An additional
isolated 24 VDC power supply is included with the
4-20 mA output option. A digital input is standard.
A fully loaded PD6363 meter has the following: four
SPDT relays, 4-20 mA output, and two 24 VDC power
supplies. The PD6363 capabilities may be enhanced
by adding the following external expansion modules:
four SPST relays –creating an eight-relay dual-input
process meter, two digital I/O modules with four inputs
and four outputs each, serial communication adapters
for use with MeterView Pro or Modbus RTU, and a dual
isolated 4-20 mA output expansion module.
Ordering Information
Standard Models
85-265 VAC
Model
12-24 VDC
Model
Options Installed
PD6363-6R0
PD6363-7R0
No options
PD6363-6R2
PD6363-7R2
2 relays
PD6363-6R3
PD6363-7R3
4-20 mA output
PD6363-6R4
PD6363-7R4
4 relays
PD6363-6R5
PD6363-7R5
2 relays& 4-20 mA output
PD6363-6R7
PD6363-7R7
4 relays & 4-20 mA output
SunBright Display Models
85-265 VAC
Model
12-24 VDC
Model
Options Installed
PD6363-6H0
PD6363-7H0
No options
PD6363-6H2
PD6363-7H2
2 relays
PD6363-6H3
PD6363-7H3
4-20 mA output
PD6363-6H4
PD6363-7H4
4 relays
PD6363-6H5
PD6363-7H5
2 relays& 4-20 mA output
PD6363-6H7
PD6363-7H7
4 relays & 4-20 mA output
Accessories
Model
Description
PDA1002
DIN rail mounting kit for two devices
PDA1004
4 SPST (Form A) relays module
PDA1011
Dual isolated analog output
PDA1044
4 digital inputs & 4 digital outputs module
PDA1232
RS-232 serial adapter
PDA1485
RS-485 serial adapter
PDA7485-I
RS-232 to RS-485 isolated converter
PDA8008
USB Adapter
PDA8232-N
USB to RS-232 non-isolated converter
PDA8485-I
USB to RS-485 isolated converter
PDA-LH
Light / horn accessory
MOD-LH
Light / horn / enclosure modification
PDA2360
Plastic control stations series
PD659
Signal isolators, splitters, & conditioners
PD9501
Multi-function calibrator
PD9502
Low-cost signal generator
PDX6901
Snubber: 0.01 μF/470 Ω, 250 VAC
Enclosures
Series
Meters
Material
PDA2300
1-10
Plastic NEMA 4X
PDA2500
1-6
Plastic NEMA 4X
PDA2600
1-6
Stainless Steel NEMA 4X
PDA2700
1-6
Painted Steel NEMA 4
PDA2800
1-2
Plastic NEMA 4X
PDA3400
1-3
Plastic NEMA 4X
Need help selecting the right enclosure?
Go to www.predig.com/esu
Replacement Option Cards
Model
Options Installed
PD1102
2 relays
PD1103
4-20 mA output
PD1104
4 relays
PD1105
2 relays& 4-20 mA output
PD1107
4 relays & 4-20 mA output

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
7
Light / Horn Accessories
PROVUMeter Shown in a PDA2301 Enclosure with MOD-LHRB1 Red Light / Horn and Button.
Meter & Enclosure Sold Separately. Assembly Required.
MOD-LH
Model
Description
MOD-LHRB1
Red Light / Horn and Button with
Holes Drilled in Enclosure(1)
MOD-LHGB1
Green Light / Horn and Button with
Holes Drilled in Enclosure(1)
MOD-LHYB1
Yellow Light / Horn and Button with
Holes Drilled in Enclosure(1)
MOD-LHBB1
Blue Light / Horn and Button with
Holes Drilled in Enclosure(1)
MOD-LHWB1
White Light / Horn and Button with
Holes Drilled in Enclosure(1)
MOD-LH5CB1
Light / Horn with User Choice of
Red, Green, Yellow, Blue or White
Light, Button, and Holes Drilled in
Enclosure(1)
Note:
1. This MOD supplies the Light / Horn and Button. The enclosure
comes pre-drilled with holes for Light / Horn and Button and the
user performs the installation and wiring. Meter and enclosure are
sold separately. The Light / Horn hole is in the back left corner of
the enclosureand the Button is centered on the cover of the
enclosure below the meter about an inch off the bottom of the
cover except on the PDA3400 series where it is mounted on the
side of the enclosure.
PDA-LH & PDA-BUTTON
Model
Description
PDA-LHR
Red Light / Horn
PDA-LHG
Green Light / Horn
PDA-LHY
Yellow Light / Horn
PDA-LHB
Blue Light / Horn
PDA-LHW
White Light / Horn
PDA-LHW
White Light / Horn
PDA-LH5C
Light / Horn with User Choice of
Red, Green, Yellow, Blue or White
Light
PDA-BUTTON1R
Red Button
PDA-BUTTON1G
Green Button
PDA-BUTTON1B
Blue Button

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
8
PDA2360 Control Stations
Model
Description
PDA2360-E
Emergency button
PDA2361-A
Ack button
PDA2361-B
Blank button
PDA2361-R
Reset button
PDA2361-T
Tare button
PDA2361-S
Stop button
PDA2361-Q
Silence button
PDA2362-AR
Ack and Reset buttons
PDA2362-BB
Two blank buttons
PDA2364-MRUE
Menu, right, up, enter buttons
Note: Control stations with one button may be connected directly to the
meter via the F4 terminal. A PDA1044 (4) digital inputs & (4) digital
outputs module is required to operate the control stations of more than
one button. See Remote Operation of Meter on page 20 for details.
Signal Splitter & Conditioner Accessories
Model
Description
PD659-1MA-1MA
Signal Isolator with One 4-20 mA
Input and One 4-20 mA Output
PD659-1MA-2MA
Signal Splitter with One 4-20 mA
Input and Two 4-20 mA Outputs
PD659-1V-1MA
Signal Conditioner with One 0-10
VDC Input and One 4-20 mA Output
PD659-1MA-1V
Signal Conditioner with One
4-20 mA Input and One 0-10 VDC
Output

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
9
Specifications
Except where noted all specifications apply to
operation at +25°C.
General
Display
Line 1: 0.60" (15 mm) high, red LEDs
Line 2: 0.46" (12 mm) high, red LEDs
6 digits each (-99999 to 999999), with lead
zero blanking
Display
Intensity
Eight user selectable intensity levels
Default value is six.
Display
Update Rate
Rate: 10 per second; up to 1 per 100
seconds (and is a function of Low Gate
setting); Total: 10 per second (fixed)
Overrange
Display flashes 999999
Display
Assignment
Display lines 1 & 2 may be assigned to
show:
•One or more rate channels: Channel A
(Ch-A), B (Ch-B), or C (Ch-C)
•Toggle between rate channels: Ch-A &
Ch-B, Ch-A & Ch-C, Ch-B & Ch-C, and
Ch-A, Ch-B, & Ch-C
•Total or grand total: Ch-A or Ch-B
•Rate and total or grand total:
Ch-A or Ch-B
•Relay set points
•Max and/or min values:
Ch-A, Ch-B, or Ch-C
•Toggle between any rate channel &
units
•Total and units: Ch-A or Ch-B
•Toggle between totals:
Ch-A & Ch-B; Ch-A, Ch-B, and sum of
Ch-A and Ch-B
•Modbus input
Line 2 may also be set to show engineering
units or be off, with no display.
Programming
Methods
Four front panel buttons, digital inputs, PC
and MeterView Pro software, or Modbus
registers.
Recalibration
All ranges are calibrated at the factory.
Recalibration is recommended at least every
12 months.
Max/Min
Display
Max/min readings reached by the process
are stored until reset by the user or until
power to the meter is turned off.
Rounding
Select 1, 2, 5, 10, 20, 50, or 100
(e.g. rounding = 10, value = 123.45,
display = 123.50).
Password
Three programmable passwords restrict
modification of programmed settings and
two prevent resetting the totals.
Pass 1: Allows use of function keys and
digital inputs
Pass 2: Allows use of function keys, digital
inputs and editing set/reset points
Pass 3: Restricts all programming, function
keys, and digital inputs.
Total: Prevents resetting the total manually
Gtotal: Prevents resetting the grand total
manually
Non-Volatile
Memory
All programmed settings are stored in non-
volatile memory for a minimum of ten years
if power is lost.
Power
Options
85-265VAC50/60Hz;90-265VDC,20Wmax;
12-24 VDC, 12-24 VAC, 15 W max.
Powered over USB for configuration only.
Fuse
Required external fuse: UL Recognized, 5 A
max, slow blow; up to 6 meters may share
one 5 A fuse
Isolation
4 kV input/output-to-power line
500 V input-to-output or output-to-P+ supply
Overvoltage
Category
Installation Overvoltage Category II:
Local level with smaller transient
overvoltages than Installation Overvoltage
Category III.
Environmental
Operating temperature range:
-40 to 65°C
Storage temperature range:
-40 to 85°C
Relative humidity:
0 to 90% non-condensing
Connections
Removable screw terminal blocks accept 12
to 22 AWG wire, RJ45 for external relays,
digital I/O, and serial communication
adapters.
Enclosure
1/8 DIN, high impact plastic, UL 94V-0,
color: black
Front Panel
NEMA 4X, IP65
Mounting
1/8 DIN panel cutout required:
3.622" x 1.772" (92 mm x 45 mm)
Two panel mounting bracket assemblies are
provided.
Tightening
Torque
Screw terminal connectors: 5 lb-in (0.56 Nm)
Overall
Dimensions
4.68" x 2.45" x 5.64"
(119 mm x 62 mm x 143 mm)
(W x H x D)
Weight
9.5 oz (269 g)
Warranty
3 years parts & labor. See Warranty
Information and Terms & Conditions on
www.predig.com for complete details.

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
10
Dual Pulse Inputs
Two Inputs
Field selectable: Pulse or square wave
0-5 V, 0-12 V, or 0-24 V @ 30 kHz; TTL;
open collector 4.7 kpull-up to 5 V @
30 kHz; NPN or PNP transistor, switch
contact 4.7 kpull-up to 5 V @ 40 Hz;
Modbus PV (Slave)
Isolated
Transmitter
Power Supply
Terminals P+ & P-: 24 VDC 10%.
All models selectable for 24, 10, or 5 VDC
supply (internal jumper J4). 85-265 VAC
models rated @ 200 mA max, 12-24 VDC
powered models rated @ 100 mA max.
5 & 10 VDC supply rated @ 50 mA max.
Refer to Flowmeter Supply Voltage
Selection (P+, P-) on page 16.
When the Light / Horn is powered by the
transmitter power supply, see MOD-LH
Light / Horn's transmitter power supply
specification in MOD-LH manual for
additional details. Light / Horn power not
available for 5 or 10 VDC supplies.
Channels
Channel A, Channel B,
Channel C (Math channel)
Programmable
Constants
Constant P (Adder):
-99.999 to 999.999, default: 0.000
Constant F (Factor):
0.001 to 999.999, default: 1.000
Math
Functions
Name
Function
Setting
Addition
(A+B+P)*F
Sunm
Difference
(A-B+P)*F
diF
Absolute diff.
((Abs(A-B))+P)*F
diFAbS
Average
(((A+B)/2)+P)*F
AVG
Multiplication
((A*B)+P)*F
nmulti
Division
((A/B)+P)*F
diVide
Max of A or B
((AB-Hi)+P)*F
Hi-Ab
Min of A or B
((AB-Lo)+P)*F
Lo-Ab
Draw
((A/B)-1)*F
drAuw
Weighted avg.
((B-A)*F)+A
uw avg
Ratio
(A/B)*F
ratio
Ratio 2
((B-A)/A)+P)*F
ratio2
Concentration
(A/(A+B))*F
Concen
Total Addition
(tA+tB+P)*F
Sunm t
G. Tot. Addition
(GtA+GtB+P)*F
SunmGT
Total
Difference
(tA-tB+P)*F
Dif GT
G. Tot.
Difference
(GtA-GtB+P)*F
Dif GT
Total Ratio
(tA/tB)*F
Tratio
Total Ratio 2
((tB-tA)/tA)*F
t-rat2
Total Percent
(tA/(tA+tB))*100
T PCT
Note: The F constant can be any value from
0.001 to 999.999. If the value is less than 1,
it willhave the same effect as a divider. For
example, the average could also be derived
by using (A+B)*F, where F = 0.500.
Low Voltage
Mag Pickup
Sensitivity: 40 mVp-p to 8Vp-p
Minimum
Input
Frequency
0.001 Hz
Minimum frequency is dependent on high
gate setting.
Maximum
Input
Frequency
30,000 Hz (10,000 for low voltage mag
pickup)
Input
Impedance
Pulse input: Greater than 300 k@ 1 kHz.
Open collector/switch input: 4.7 kpull-up
to 5 V.
Sequence of
Operations
for Input
Programming
1. Select Input for A and B
2. Set up the rate, total, and grand total
engineering units for channels A & B,
and units for math channel C
3. Set up rate, total, and grand total
decimal points for channels A & B,
and decimal point for math channel C
4. Program channel A & B rate
parameters
5. Program channel A & B total and reset
parameters
6. Set up display lines 1 & 2 and display
intensity
7. Select the transfer function for A & B
(e.g. Linear)
8. Select Math function for Channel C
9. Program constants for Factor (F) and
Adder (P).
10. Program cutoff values for A and B
Accuracy
±0.03% of calibrated span ±1 count
Temperature
Drift
Rate display is not affected by changes in
temperature.
Multi-Point
Linearization
2 to 32 points for channel A and B
Low-Flow
Cutoff
0.1 to 999,999 (0 disables cutoff function).
Point below at which the display always
shows zero.
Decimal Point
Up to five decimal places or none:
d.ddddd, d.dddd, d.ddd, d.dd, d.d, or dddddd
Calibration
May be calibrated using K-factor, internal
calibration, or by applying an external
calibration signal.
K-Factor
Field programmable K-factor converts input
pulses to rate in engineering units. May be
programmed from 0.00001 to 999,999
pulses/unit.
Calibration
Range
Input 1 signal may be set anywhere in the
range of the meter; input 2 signal may be
set anywhere above or below input 1
setting.
Minimum input span between any two
inputs is 10 Hz. An error message will
appear if the input span is too small.
Filter
Programmable contact de-bounce filter:
40 to 999 Hz maximum input frequency
allowed with low speed filter.
Time Base
Second, minute, hour, or day
Gate
Low gate: 0.1-99.9 seconds
High gate: 2.0-999.9 seconds

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
11
Dual Rate/Totalizer
Rate Display
Indication
-99999 to 999999, lead zero blanking.
Total Display
& Total
Overflow
0 to 999,999; automatic lead zero
blanking.
Up to 999,999,999 with total-overflow
feature. “oF” is displayed to the left of total
overflow and ▲ LED is illuminated.
Total
Decimal Points
Up to five decimal places or none:
d.ddddd, d.dddd, d.ddd, d.dd, d.d, or dddddd
Total decimal point is independent of rate
decimal point. Channel A and B decimal
points programmed independently.
Dual Totalizer
Calculates total for channels A and B
based on rate and field programmable
multiplier to display total in engineering
units. Time base must be selected
according to the time units in which the
rate is displayed. Channel A and B
totalizer parameters programmed
independently.
Totalizer
Rollover
Totalizer rolls over when display exceeds
999,999,999. Relay status reflects
display.
Total
Overflow
Override
Program total A or B total reset for
automatic with 0.1 second delay and set
point 1 for 999,999
Totalizer
Alarm Presets
Up to eight, user selectable under setup
menu. Any set point can be assigned to
channel A or B total or grand total (or C)
and may be programmed anywhere in
the range of the meter for total alarm
indication.
Total & Grand
Total Reset
Via front panel button, external contact
closure on digital inputs, automatically via
user selectable preset value and time
delay, or through serial communications.
Channel A and B total and grand total
reset parameters programmed
independently.
Total Reset
Password
Total and grand total passwords may be
entered to prevent resetting the totals or
grand totals from the front panel.
Programmable
Delay
On Release
0.1 and 999.9 seconds; applied to the
first relay assigned to total or grand total.
If the meter is programmed to reset total
to zero automatically when the preset is
reached, then a delay will occur before
the total is reset.
Non-Resettable
Total
The grand totals can be programmed as
non-resettable totals by entering the
password “050873”. Both channels are
set to non-resettable when this password
is entered.
•Once the Grand Total has been programmed as “non-
resettable” the feature CANNOT be disabled.
Relays
Rating
2 or 4 SPDT (Form C) internal and/or 4
SPST (Form A) external; rated 3 A @ 30
VDC and 125/250 VAC resistive load; 1/14
HP (≈50 W) @ 125/250 VAC for inductive
loads
Noise
Suppression
Noise suppression is recommended for each
relay contact switching inductive loads; see
Switching Inductive Loads on page 18 for
details.
Relay
Assignment
Relays may be assigned to channel A or B
rate, total, or grand total; channel C; or
Modbus control.
Deadband
0-100% of span, user programmable
High or Low
Alarm
User may program any alarm for high or low
trip point.
Unused alarm LEDs and relays may be
disabled (turn off).
Relay
Operation
•Automatic (non-latching) and/or manual
reset
•Latching (requires manual
acknowledge) with or without clear
•Pump alternation control (2-8 relays)
•Sampling (based on set point and time)
•Off (disable unused relays and enable
Interlock feature)
•Manual on/off control mode
Relay Reset
User selectable via front panel button, F4
terminal at back of meter, external contact
closure on digital inputs, or through serial
communications.
1. Automatic reset only (non-latching),
when the input passes the reset point.
2. Automatic + manual reset at any time
(non-latching)
3. Manual reset only, at any time
(latching)
4. Manual reset only after alarm condition
has cleared (L)
Note: Front panel button, F4 terminal at
back of meter or digital input may be
assigned to acknowledge relays
programmed for manual reset.
Time Delay
0 to 999.9 seconds, on & off relay time
delays. Programmable and independent for
each relay
Fail-Safe
Operation
Programmable and independent for each
relay.
Note: Relay coil is energized in non-alarm
condition. In case of power failure, relay will
go to alarm state.
Auto
Initialization
When power is applied to the meter, relays
will reflect the state of the input to the meter.
Additional
Relays
An external module, model PDA1004, is
available to add 4 SPST 3 A relays to the
meter.

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
12
Isolated 4-20 mA Transmitter
Output
Output
Source
Input channels A or B, rate, total, or grand
total; channel C; max or min for channel A
or B; highest or lowest max or min of A and
B; set points 1-8; Modbus input; or manual
control mode
Scaling
Range
1.000 to 23.000 mA for any display range
Calibration
Factory calibrated:
4.000 to 20.000 = 4-20 mA output
Analog Out
Programming
23.000 mA maximum for all parameters:
Overrange, underrange, max, min, and
break
Accuracy
± 0.1% of span ± 0.004 mA
Temperature
Drift
0.4 µA/C max from 0 to 65C ambient,
0.8 µA/C max from -40 to 0C ambient
Note: Analog output drift is separate from input
drift.
Isolated
Transmitter
Power Supply
TerminalsI+&R:24VDC10%.May be
used to power the 4-20 mA output or other
devices.
All models rated@ 40 mA max.
External Loop
Power Supply
35 VDC maximum
Output Loop
Resistance
Power supply
Minimum
Maximum
24 VDC
10 
700 
35 VDC
(external)
100 
1200 
0-10 VDC
Output
The PD659-1MA-1V can convert the
optional 4-20 mA output to a 0-10 VDC
output
Additional
4-20 mA
Outputs
An external module, model PDA1011,is
available to add two 4-20 mA outputs to the
meter.
USB Connection
Function
Programming only
Compatibility
USB 2.0 Standard, Compliant
Connector Type
Micro-B receptacle
Cable
USB A Male to Micro-B Cable
Driver
Microsoft®Windows®XP/Vista/7/8/10
Power
USB port provides power to the meter.
DO NOT apply AC or DC power to the
meter while the USB port is in use.
On-Board Digital Input (F4)
Function
Remote operation of front-panel buttons,
acknowledge/reset relays, reset totals,
reset max/min values. See Function Keys &
Digital I/O Available Settings on page 48 for
a complete list of capabilities.
Contacts
3.3 VDC on contact. Connect normally
open contacts across F4 to COM
Logic Levels
Logic High: 3 to 5 VDC
Logic Low: 0 to 1.25 VDC
Additional I/O
Up to 2 external modules, model PDA1044
with 4 digital inputs and 4 digital outputs
each can be added.
Modbus®RTU Serial
Communications
Slave Id
1 –247 (Meter address)
Baud Rate
300 –19,200 bps
Transmit
Time Delay
Programmable between 0 and 199 ms
Data
8 bit (1 start bit, 1 or 2 stop bits)
Parity
Even, Odd, or None with 1 or 2 stop bits
Byte-To-Byte
Timeout
0.01 –2.54 second
Turn Around
Delay
Less than 2 ms (fixed)
Note: Refer to the PROVUModbus Register Tables located
at www.predig.com for details.
MeterView Pro
Availability
Download directly from meter or from
www.predig.com/download_software
System
Requirements
Microsoft®Windows®XP/Vista/7/8/10
Communications
USB 2.0 (for programming only)
(Standard USB A to Micro USB B)
RS-232 adapter, RS-485 adapter and
RS-485 to USB converter
(programming, monitoring, and data
logging)
Configuration
Configure meters one at a time
Power
USB port provides power to the meter.
DO NOT apply AC or DC power to the
meter while the USB port is in use.

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
13
Compliance Information
Safety
UL & c-UL Listed
USA & Canada
UL 508 Industrial Control Equipment
UL File Number
E160849
Front Panel
UL Type 4X, NEMA 4X, IP65; panel
gasket provided
Low Voltage
Directive
EN 61010-1:2010
Safety requirements for measurement,
control, and laboratory use
Electromagnetic Compatibility
Emissions
EN 55022:2010
Class A ITE emissions requirements
Radiated
Emissions
Class A
AC Mains
Conducted
Emissions
Class A
Immunity
EN 61326-1:2013
Measurement, control, and laboratory
equipment
EN 61000-6-2:2005
EMC heavy industrial generic
immunity standard
RFI - Amplitude
Modulated
80 -1000 MHz 10 V/m 80% AM
(1 kHz)
1.4 - 2.0 GHz 3 V/m 80% AM (1 kHz)
2.0 - 2.7 GHz 1 V/m 80% AM (1 kHz)
Electrical Fast
Transients
±2kV AC mains, ±1kV other
Electrostatic
Discharge
±4kV contact, ±8kV air
RFI -
Conducted
10V, 0.15-80 MHz, 1kHz 80% AM
AC Surge
±2kV Common, ±1kV Differential
Surge
1KV (CM)
Power-
Frequency
Magnetic Field
30 A/m 70%V for 0.5 period
Voltage Dips
40%V for 5 & 50 periods
70%V for 25 periods
Voltage
Interruptions
<5%V for 250 periods
Note:
Testing was conducted on meters installed
through the covers of grounded metal enclosures
with cable shields grounded at the point of entry
representing installations designed to optimize
EMC performance.
Safety Information
•Read complete instructions prior to installation
and operation of the meter.
•Risk of electric shock or personal injury.
•Hazardous voltages exist within enclosure.
Installation and service should be performed only
by trained service personnel.
Installation
There is no need to remove the meter from its
case to complete the installation, wiring, and
setup of the meter for most applications.
Instructions are provided for changing the
transmitter power supply to output 5 or 10 VDC
instead of 24 VDC. See Figure 5. Transmitter
Supply Voltage Selection on page 16.
Unpacking
Remove the meter from box. Inspect the
packaging and contents for damage. Report
damages, if any, to the carrier.
If any part is missing or the meter malfunctions,
please contact your supplier or the factory for
assistance.

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
14
Panel Mounting Instructions
•Prepare a standard 1/8 DIN panel cutout -
3.622" x 1.772" (92 mm x 45 mm). Refer to
Figure 1. 1/8 DIN Panel Cutout Dimensions
below for more details.
•Clearance: allow at least 6.0" (152 mm) behind
the panel for wiring.
•Panel thickness: 0.04" - 0.25" (1.0 mm - 6.4 mm).
Recommended minimum panel thickness to
maintain Type 4X rating: 0.06" (1.5 mm) steel
panel, 0.16" (4.1 mm) plastic panel.
•Remove the two mounting brackets provided with
the meter (back-off the two screws so that there is
¼" (6.4 mm) or less through the bracket. Slide the
bracket toward the front of the case and remove).
•Insert meter into the panel cutout.
•Install mounting brackets and tighten the screws
against the panel. To achieve a proper seal,
tighten the mounting bracket screws evenly until
meter is snug to the panel along its short side.
DO NOT OVER TIGHTEN, as the rear of the
panel may be damaged.
Figure 1. 1/8 DIN Panel Cutout Dimensions
DO NOT apply AC or DC power to the meter when using the
Micro USB connection.
Figure 2. Panel Mounting Details
Mounting Dimensions
Figure 3. Meter Dimensions - Side View
Figure 4. Meter Dimensions - Top View
NO NC NC C NO C
NO NC NC C NO C+ -R
3.622" (92 mm)
1.772"
(45mm)
Panel Cutout
to DIN 43700
Square Corners to 0.060"
(1.5mm) Max Radius
A
B
Tolerances:
A: +0.032 (+0.8mm)
-0.000 (-0.0mm)
B: +0.024 (+0.6mm)
-0.000 (-0.0mm)

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
15
Installation Overview
We recommend the following sequence for getting the
meter into service:
1. DO NOT apply AC or DC power to the meter.
2. Connect the meter to the PC with the USB cable
provided. DO NOT use a different USB cable.
3. If MeterView Pro (MVPro) is already installed in
your computer, then the program will launch
automatically in most systems. If the program
does not start automatically, double-click on the
MVPro icon.
4. If MVPro is not installed, follow the instructions
provided below.
5. Use MVPro to configure the meter for your
application.
6. Disconnect the USB cable from the meter.
7. Apply power and signal and check operation of
the meter.
8. Install the meter and put into service.
9. Make any programming adjustments using the
front panel buttons.
MeterView Pro Software
The easiest and quickest way to program your PROVU
meter is to use the FREE MeterView Pro
programming software. This software is loaded into
the meter and connects and installs directly to your
PC with the USB cable provided. DO NOT use a
different USB cable. We recommend that the first
thing you do after taking the meter out of the box is
connect the PROVUto your PC with the provided USB
cable. DO NOT apply AC or DC power to the meter
while your PC is connected to the meter as it will
disrupt the USB connection. It is not necessary to
apply an input signal.
MeterView Pro programming software is intuitive, and
most customers can get their meter programmed as
they like without even looking in the manual.
Watch Meterview Pro Software Video at
www.predig.com/meterviewpro
MeterView Pro Installation
1. Connect one end of the provided USB cable
to the meter and the other end to the
computer. The computer will automatically
install the driver software it needs to talk to
the meter. Follow the on-screen instructions
and allow sufficient time for the process to
complete. This can take a few minutes. If the
process is interrupted, then it could leave the
system in an unstable condition.
•Only one meter may be connected at a time.
Attaching multiple meters will cause a conflict
with the meter software.
•DO NOT apply AC or DC power to the meter
when using the Micro USB connection.
2. Once the driver is installed, an AutoPlay
dialog should appear for the drive
“MAINSTAL.” Click “Open folder to view
files.”
If the computer does not display an AutoPlay
dialog for the drive “MAINSTAL,” you should
open My Computer and double-click on the
drive labeled “MAINSTAL.”
3. Double-click on the file named “MAStart.”
The program will open a few windows and
install two programs on your computer.
Simply follow the on-screen instructions until
you see one of the dialogs below. If you
receive a “User Account Control” warning,
click “Yes.”
4. If there is an update available, click the
“Update” button to install the new version.
Otherwise, click “Configure” to begin
programming your meter.
Note: If you decide to update your MeterView Pro
software, once the installation has completed, you
will be asked if you want to update the setup files
located on the meter itself. This way, you will
always have the most current version on the meter
for future installs.
•DO NOT unplug the meter while the new
installation files are being written to it. The
meter will display uwrite during the process
and you will receive an on-screen notification
once the process is complete.

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
16
Flowmeter Supply Voltage
Selection (P+, P-)
All meters, including models equipped with the
12-24 VDC power option, are shipped from the
factory configured to provide 24 VDC power for
the transmitter or sensor.
If the transmitter requires 5 or 10 VDC excitation,
the internal jumper J4 must be configured
accordingly.
To access the voltage selection jumper:
1. Remove all the wiring connectors.
2. Unscrew the back cover.
3. Slide out the back cover by about 1
inch.
4. Configure the J4 jumper, located behind
the input signal connector, for the
desired excitation voltage as shown.
Figure 5. Transmitter Supply Voltage Selection
Connections
All connections are made to removable screw
terminal connectors located at the rear of the
meter.
•Use copper wire with 60°C or 60/75°C insulation
for all line voltage connections. Observe all safety
regulations. Electrical wiring should be performed
in accordance with all applicable national, state,
and local codes to prevent damage to the meter
and ensure personnel safety.
Connectors Labeling
The connectors’ label, affixed to the meter, shows the
location of all connectors available with requested
configuration.
Note: ## on the following figures refers to power and
display options. (Example: PD6363-6H5)
Figure 6. PD6363-##0 Connectors Label
Figure 7. PD6363-##2 Connectors Label
Figure 8. PD6363-##3 Connectors Label
Figure 9. PD6363-##4 Connectors Label
Figure 10. PD6363-##5 Connectors Label
Figure 11. PD6363-##7 Connectors Label
•DO NOT connect any equipment other than
Precision Digital’s expansion modules, cables, or
meters to the RJ45 M LINK connector. Otherwise
damage will occur to the equipment and the
meter.
POWER
+-
M-LINK
123 4 5 6 7 8
21
SIGNAL
Ch-A
P- F4P+ COM S1+
3412 5
S1- COM S2+ S2-
7869
Ch-B
POWER
+-
M-LINK
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
SIGNAL
Ch-A
P- F4P+ COM S1+
3412 5
S1- COM S2+ S2-
7869
Ch-B
R
I- I+
MA OUT
1
32
POWER
+-
M-LINK
123 4 5 6 7 8
21
SOURCE: I- to R
SINK: I- to I+
SIGNAL
Ch-A
P- F4P+ COM S1+
3412 5
S1- COM S2+ S2-
7869
Ch-B
POWER
+-
M-LINK
CNONO NC NC C
RELAY4 RELAY3
4365 2 1
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
SIGNAL
Ch-A
P- F4P+ COM S1+
3412 5
S1- COM S2+ S2-
7869
Ch-B
R
I- I+
MA OUT
1
32
POWER
+-
M-LINK
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
SOURCE: I- to R
SINK: I- to I+
SIGNAL
Ch-A
P- F4P+ COM S1+
3412 5
S1- COM S2+ S2-
7869
Ch-B
R
I- I+
MA OUT
1
32
POWER
+-
M-LINK
CNONO NC NC C
RELAY4 RELAY3
4365 2 1
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
SOURCE: I- to R
SINK: I- to I+
SIGNAL
Ch-A
P- F4P+ COM S1+
3412 5
S1- COM S2+ S2-
7869
Ch-B

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
17
Power Connections
Power connections are made to a two-terminal
connector labeled POWER. The meter will operate
regardless of DC polarity connection. The + and -
symbols are only a suggested wiring convention. There
are separate models for low voltage and high voltage
power. See Ordering Information on page 6for
details.
Figure 12. Power Connections
Signal Connections
Signal connections are made to a nine-terminal
connector labeled SIGNAL. The COM (common)
terminals are the return for certain input signals. The
two COM terminals connect to the same common
return, and are not isolated.
The following figures show examples of signal
connections.
Figure 13. Flowmeters Powered by Internal Power
Supply
Figure 14. Flowmeters Powered by External
Supply
Figure 15. Self-Powered Magnetic Pickup Coil
Flowmeter
Figure 16. NPN open Collector Input
Figure 17. PNP Sensor Powered by
Internal Supply
Figure 18. Switch Input Connections
Configure Input Type and Level
Switches
Channel A and B each have an internal input type
configuration switch. These switches must be set to
the correct input type and level. Each switch can be
set for mV, PNP, or NPN. For details on what input
type to select, see Signal Connections
starting on page 17.
To configure the meter for 12 VDC power:
1. Remove all the connectors.
2. Unscrew the back cover.
3. Remove the back cover.
4. Configure the input selection switches
for channel A and B, located behind the
input connector on the far left, as
needed.
5. Slide rear cover back onto the meter.
6. Screw the back cover on. Do not over
tighten.
7. Replace all connectors.
AC or DC
POWER
Required External Fuse:
5 A max, 250 V Slow Blow
POWER
+-

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
18
Modbus RTU Serial
Communications
Serial communications connection is made to an
RJ45 connector labeled M-LINK. For interfacing to the
PROVU®, use the PDA1232 for RS-232 or the
PDA1485 for RS-485. The same port is used for
interfacing with all expansion modules (e.g. external
relays, additional 4-20 mA outputs, digital I/O).
Relay Connections
Relay connections are made to two six-terminal
connectors labeled RELAY1 –RELAY4. Each relay’s
C terminal is common only to the normally open (NO)
and normally closed (NC) contacts of the
corresponding relay. The relays’ C terminals should
not be confused with the COM (common) terminal of
the INPUT SIGNAL connector.
Figure 19. Relay Connections
Switching Inductive Loads
The use of suppressors (snubbers) is strongly
recommended when switching inductive loads to
prevent disrupting the microprocessor’s operation.
The suppressors also prolong the life of the relay
contacts. Suppression can be obtained with resistor-
capacitor (RC) networks assembled by the user or
purchased as complete assemblies. Refer to the
following circuits for RC network assembly and
installation:
Figure 20. AC and DC Loads Protection
Choose R and C as follows:
R: 0.5 to 1 Ωfor each volt across the contacts
C: 0.5 to 1 µF for each amp through closed contacts
Notes:
1. Use capacitors rated for 250 VAC.
2. RC networks may affect load release time of
solenoid loads. Check to confirm proper
operation.
3. Install the RC network at the meter's relay screw
terminals. An RC network may also be installed
across the load. Experiment for best results.
Figure 21. Low Voltage DC Loads Protection
RC Networks Available from
Precision Digital
RC networks are available from Precision Digital and
should be applied to each relay contact switching an
inductive load. Part number: PDX6901.
Note: Relays are de-rated to 1/14th HP (50 watts)
with an inductive load.
CNONO NC NC C
RELAY4 RELAY3
4 36 5 2 1
CNONO NC NC C
RELAY2 RELAY1
4 36 5 2 1
C
R
C
R

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
19
F4 Digital Input Connections
A digital input, F4, is standard on the meter. This
digital input connected with a normally open closure
across F4 and COM, or with an active low signal
applied to F4. It can be used for remote operation of
front-panel buttons, to acknowledge/reset relays,
reset totals, or to reset max/min values. See Function
Keys & Digital I/O Available Settings on page 48 for a
complete list of capabilities.
Figure 22. F4 Digital Input Connections
4-20 mA Output Connections
Connections for the 4-20 mA transmitter output are
made to the connector terminals labeled MA OUT.
The 4-20 mA output may be powered internally or
from an external power supply.
Figure 23. 4-20 mA Output Connections
Analog Output Transmitter Power
Supply
The internal 24 VDC power supply powering the
analog output may be used to power other devices, if
the analog output is not used. The I+ terminal is the
+24 V and the R terminal is the return.
Figure 24. Analog Output Supply Powering Other
Devices
4-20 mA Input
Remote Display, PLC,
Chart Recorder, Etc.
-
+
RI- I+ 132
RELAY1 mA OUT
24 V
12-35 VDC
Power
Supply
+
4-20 mA
Input Meter
-+
RI- I+ 132
RELAY1
321
-
24 V
mA OUT
Internal Power Supply
and Analog Output
321
Active Output Loop Passive Output Loop
RI- I+
132
24 VDC
Powered
Device
24 V
+-

PROVU™PD6363 Dual Analog Input Rate/Totalizer
Instruction Manual
20
External Relay, Analog Output, &
Digital I/O Connections
The relay, dual analog output, and digital I/O
expansion modules PDA1004, PDA1011, and
PDA1044 are connected to the meter using a CAT5
cable provided with each module. The two RJ45
connectors on the expansion modules are identical
and interchangeable; they are used to connect
additional modules to the system.
Note: The jumper located between the RJ45
connectors of the PDA1044 must be removed
on the second digital I/O module in order for the
system to recognize it as module #2.
•DO NOT connect or disconnect the expansion
modules with the power on! More detailed
instructions are provided with each optional
expansion module.
Figure 25. Expansion Module & DIN Rail Mounting
Kit
Figure 26. External Relays Module Connections
Figure 27. Digital I/O Module Connections
Figure 28. Dual 4-20 mA Output Module Connections
Remote Operation of Meter
The meter can be operated via the front panel push
buttons or a remote control station using the
PDA1044 Digital I/O module as illustrated in Figure
29. Meter to Control Station Connection.
Figure 29. Meter to Control Station Connections
Interlock Relay Feature
As the name implies, the interlock relay feature
reassigns one, or more, alarm/control relays for use
as interlock relay(s). Interlock contact(s) are wired to
digital input(s) and activate the interlock relay. This
feature is enabled by configuring the relay, and the
corresponding digital input(s), see Setting Up the
Interlock Relay (Force On) Feature on page 40.
In the example below, an Interlock Contact switch is
connected to a digital input, which will be used to
force on (energize) the Interlock Relay. The Interlock
Relay and the Control Relay are connected in series
with the load.
•When the Interlock Contact is closed (safe), the
Interlock Relay energizes, allowing power to flow
to the Control Relay; the corresponding front
panel LED is on.
•When the Interlock Contact is open, the
corresponding front panel LED flashes (locked
out), the Interlock Relay is de-energized,
preventing power from flowing to the Control
Relay and the load.
Figure 30. Interlock Connections
1 2
RLY5 RLY6 RLY7 RLY8
3 4 5 6 7 8
NO CNO CNO CNO C
1 2 3 4 5 6
+5 I1 I2 I3 I4 O1
7 8
O2 O3
910
O4 G
DI 1-4 DO 1-4
5 VDC GND
+-
-+- +
2314
Out 3Out 2
+-
+- +-
4-20 mA
Input
Meter 2
4-20 mA
Input
Meter 3
12-35 VDC
Power
Supply 2
12-35 VDC
Power
Supply 3