Precision Digital Corporation ProVu PD6001 User manual

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
PRECISION DIGITAL CORPORATION
233 South Street • Hopkinton MA 01748 USA
Tel [phone] • Fax [phone]
www.predig.com
•1/8 DIN Digital Panel Meter with NEMA 4X, IP65 Front
•0-20 mA, 4-20 mA, 0-5 V, 1-5 V, and ±10 V Field Selectable Inputs with ±0.03% Accuracy
•Feet & Inches Display Ideal for Level Applications
•Dual-Line 6-Digit Display, 0.6" (15 mm) & 0.46" (12 mm)
•Isolated 24 VDC @ 200 mA Transmitter Power Supply
•Easy Field Scaling in Engineering Units without Applying an Input
•2 or 4 Relays with Interlocking Capability + Isolated 4-20 mA Output Options
•Free PC-Based, On-Board, MeterView Pro USB Programming Software
•No Assembly Required
•Optional SunBright Display Models for Outdoor Applications
•Operating Temperature Range: -40 to 65°C (-40 to 149°F)
•UL & C-UL Listed. E160849; 508 Industrial Control Equipment
•Input Power Options: 85-265 VAC / 90-265 VDC or 12-24 VDC
•Display Input in Two Different Scales Simultaneously - Great for Level Applications
•Multi-Pump Alternation Control
•Round Horizontal Tank Function; Just Enter Diameter & Length
•32-Point Linearization
•Programmable Display, Function Keys & Digital Input
•External 4-Relay & Digital I/O Expansion Modules
•Password Protection
•RS-232 & RS-485 Serial Communication Options with Modbus RTU
•Wide Assortment of NEMA 4X Enclosures for up to Ten Meters
•Light / Horn & Reset Button Accessory
•Control Station Accessory for Remote Operation
•3-Year Warranty
MeterView Pro
USB Install

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
2
Disclaimer
The information contained in this document is
subject to change without notice. Precision
Digital makes no representations or warranties
with respect to the contents hereof and
specifically disclaims any implied warranties of
merchantability or fitness for a particular
purpose. See Warranty Information and Terms
& Conditions on www.predig.com for complete
details.
•Read complete instructions prior to installation
and operation of the meter.
•Risk of electric shock or personal injury.
•This product is not recommended for life support
applications or applications where
malfunctioning could result in personal injury or
property loss. Anyone using this product for
such applications does so at his/her own risk.
Precision Digital Corporation shall not be held
liable for damages resulting from such improper
use.
WARNING
Cancer and Reproductive Harm - www.P65Warnings.ca.gov
Limited Warranty
Precision Digital Corporation warrants this
product against defects in material or
workmanship for the specified period under
“Specifications” from the date of shipment from
the factory. Precision Digital’s liability under this
limited warranty shall not exceed the purchase
value, repair, or replacement of the defective
unit. See Warranty Information and Terms &
Conditions on www.predig.com for complete
details.
Registered Trademarks
All trademarks mentioned in this document are
the property of their respective owners.
© 2022 Precision Digital Corporation.
All rights reserved.
FREE MeterView Pro
Programming Software
The meter can be powered from the USB connection. When
using the USB connection, DO NOT apply AC or DC power to
the meter.
The easiest and quickest way to program your
PROVUmeter is to use the FREE MeterView Pro
programming software. This software is loaded into
the meter and connects and installs directly to your
PC with a USB cable. We recommend that the first
thing you do after taking the meter out of the box is
connect the PROVUto your PC with the provided
USB cable –do not use a different cable. DO NOT
apply AC or DC power to the meter while your PC is
connected to the meter as it will disrupt the USB
connection. You don’t even have to apply an input
signal.
MeterView Pro programming software is intuitive,
and most customers can get their meter
programmed as they like without even looking in the
manual.
Watch MeterView Pro Software Video at
www.predig.com/meterviewpro
In addition to programming, the software may be
used for:
•Monitoring
•Datalogging using your PC
•Generating and saving programming files
for later use
Once your meter is programmed the way you want it,
you can wire it up for your application per the
instructions in this manual and install it. If you find
that you need to make adjustments to the
programming after the meter is installed, you can
use the front panel buttons and the instructions in
this manual to do so.

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
3
Table of Contents
Introduction..........................................................................................................6
Ordering Information...........................................................................................6
Specifications.....................................................................................................10
General...........................................................................................................10
Process Input.................................................................................................11
Relays.............................................................................................................11
Isolated 4-20 mA Transmitter Output ..........................................................12
USB Connection............................................................................................12
On-Board Digital Input (F4)...........................................................................12
Modbus®RTU Serial Communications........................................................12
MeterView Pro Software................................................................................12
Compliance Information....................................................................................13
Safety..............................................................................................................13
Electromagnetic Compatibility.....................................................................13
EU Declaration of Conformity...........................................................................13
Safety Information .............................................................................................13
Installation..........................................................................................................13
Unpacking......................................................................................................13
Panel Mounting Instructions ........................................................................14
Mounting Dimensions..................................................................................14
Installation Overview.....................................................................................15
MeterView Pro Software................................................................................15
MeterView Pro Installation...........................................................................15
Transmitter Supply Voltage Selection (P+, P-)...........................................16
Connections...................................................................................................16
Connectors Labeling ...................................................................................16
Power Connections.....................................................................................17
Signal Connections .....................................................................................17
Modbus RTU Serial Communications.........................................................17
Relay Connections......................................................................................17
Switching Inductive Loads...........................................................................18
F4 Digital Input Connections.......................................................................18
4-20 mA Output Connections......................................................................18
Analog Output Power Supply......................................................................18
External Relays & Digital I/O Connections..................................................19
Remote Operation of Meter.........................................................................19
Interlock Relay Feature...............................................................................19
Setup and Programming...................................................................................20
Overview.........................................................................................................20
Front Panel Buttons and Status LED Indicators ........................................20
Display Functions & Messages....................................................................21
Main Menu......................................................................................................22
Setting Numeric Values ................................................................................23
Setting Up the Meter (setup)........................................................................23
Setting the Input Signal (Input)..................................................................24
Setting the Input Units or Custom Tags (units).........................................24
Setting the Decimal Point (dEc pt).............................................................25
Programming the Meter (prog)...................................................................25
Setting the Display Parameter & Intensity (dsplay) ...................................27
Display Intensity (d-Inty)...........................................................................27
Setting the Relay Operation (relay)............................................................28
Setting the Relay Action..............................................................................28
Programming Set and Reset Points............................................................29
Setting Fail-Safe Operation.........................................................................29
Programming Time Delay............................................................................29
Relay Action for Loss of 4-20 mA Input (Loop Break).................................29

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
4
Relay and Alarm Operation Diagrams.........................................................29
HighAlarm Operation (Set >Reset)..............................................................29
Low Alarm Operation (Set < Reset)............................................................30
High Alarm with Fail-Safe Operation (Set > Reset).....................................30
Low Alarm with Fail-Safe Operation (Set < Reset) .....................................30
Time Delay Operation .................................................................................30
Pump Alternation Control Operation ...........................................................31
Relay Sampling Operation ..........................................................................31
Relay Operation Details................................................................................32
Overview .....................................................................................................32
Relays Auto Initialization.............................................................................32
Fail-Safe Operation.....................................................................................32
Front Panel LEDs........................................................................................32
Latching and Non-Latching Relay Operation ..............................................32
Non-Latching Relay (Auto) .........................................................................33
Non-Latching Relay with Manual Reset (A-nman).......................................33
Latching Relay (LatcH)...............................................................................33
Latching Relay with Clear (Lt-Clr)............................................................33
Acknowledging Relays................................................................................34
Pump Alternation Control Applications (Altern) ........................................34
Setting Up the Interlock Relay (Force On) Feature.....................................35
Scaling the 4-20 mA Analog Output (Aout).................................................36
Reset Menu (reset).......................................................................................36
Manual Control Menu (Contrl).....................................................................36
Setting Up the Password (pass)...................................................................37
Protecting or Locking the Meter ..................................................................37
Making Changes to a Password Protected Meter.......................................37
Disabling Password Protection....................................................................37
Advanced Features Menu.............................................................................38
Advanced Features Menu & Display Messages..........................................38
Noise Filter (filter)...................................................................................39
Noise Filter Bypass (bypass)......................................................................39
Rounding Feature (round)..........................................................................39
Modbus RTU Serial Communications (serial)..........................................40
Select Menu (SElect).................................................................................40
Input Signal Conditioning (Functn).............................................................40
Low-Height Cutoff (CutofF)........................................................................41
Analog Output Programming (AoutPr) .......................................................42
Programmable Function Keys User Menu (user).......................................43
Internal Source Calibration (ICAL) ..............................................................44
Meter Operation .................................................................................................45
Front Panel Buttons Operation....................................................................45
Function Keys Operation..............................................................................45
F4 Operation ..................................................................................................45
Maximum/Minimum Readings......................................................................45
Troubleshooting.................................................................................................46
Diagnostics Menu (diag) ..............................................................................46
Testing the Display LEDs............................................................................46
Determining Software Version.....................................................................46
Reset Meter to Factory Defaults...................................................................46
Factory Defaults & User Settings................................................................47
Troubleshooting Tips....................................................................................48

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
5
Table of Figures
Figure 1. 1/8 DIN Panel Cutout Dimensions....................................................14
Figure 2. Panel Mounting Details .....................................................................14
Figure 3. Meter Dimensions - Side View..........................................................14
Figure 4. Meter Dimensions - Top View...........................................................14
Figure 5. Transmitter Supply Voltage Selection.............................................16
Figure 6. PD6001-##0 Connectors Label .........................................................16
Figure 7. PD6001-##2 Connectors Label .........................................................16
Figure 8. PD6001-##3 Connectors Label .........................................................16
Figure 9. PD6001-##4 Connectors Label .........................................................16
Figure 10. PD6001-##5 Connectors Label .......................................................16
Figure 11. PD6001-##7 Connectors Label .......................................................16
Figure 12. Power Connections .........................................................................17
Figure 13. Transmitter Powered by Internal Supply.......................................17
Figure 14. Transmitter Powered by External Supply or Self-Powered .........17
Figure 15. Voltage Input Connections .............................................................17
Figure 16. Relay Connections...........................................................................17
Figure 17. AC and DC Loads Protection..........................................................18
Figure 18. Low Voltage DC Loads Protection.................................................18
Figure 19. F4 Digital Input Connections..........................................................18
Figure 20. 4-20 mA Output Connections .........................................................18
Figure 21. Analog Output Supply Powering Other Devices...........................18
Figure 22. Expansion Module & DIN Rail Mounting Kit..................................19
Figure 23. External Relays Module Connections............................................19
Figure 24. Digital I/O Module Connections......................................................19
Figure 25. Meter to Control Station Connection.............................................19
Figure 26. Interlock Connections.....................................................................19

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
6
Introduction
The PROVUPD6001 is a multi-purpose, easy-to-use
digital process meter featuring a bright, easy-to-read
main display with convenient feet and inches
designations. It is ideal for level applications requiring
an easy-to-understand display, as it shows feet,
inches, and fractions of an inch. Its superluminous
LED digits make it easily readable in smoke, dust,
fog, and, with the optional SunBright®display, even
direct sunlight.
The PD6001 accepts current and voltage signals
(e.g. 4-20 mA, 0-10 V). Three of the front panel
buttons can be custom-programmed for a specific
operation. The analog input can be scaled to display
the process in two different scales. The main display
can indicate level in feet and inches with printed feet
and inches designations, and the second display
could be used to indicate some other scale, such as
the volume in gallons or liters.
The basic model includes an isolated 24 VDC
transmitter power supply that can be used to power
the input transmitter or other devices. An additional
isolated 24 VDC power supply is included with the
4-20 mA output option. A digital input is standard.
A fully loaded PD6001 meter has the following: four
SPDT relays, 4-20 mA output, and two 24 VDC power
supplies. The PD6001 capabilities may be enhanced
by adding the following external expansion modules:
four SPST relays (creating an eight-relay process
meter), two digital I/O modules with four inputs and four
outputs each, and USB, RS-232 or RS-485
communication adapters.
The eight relays can be used for alarm indication or
process control applications such as pump alternation
control. The 4-20 mA isolated output, Modbus RTU
serial communications, and digital I/O options make the
PD6001 an excellent addition to any level monitoring or
control system.
Ordering Information
Standard Models
85-265 VAC
Model
12-24 VDC
Model
Options Installed
PD6001-6R0
PD6001-7R0
No options
PD6001-6R2
PD6001-7R2
2 relays
PD6001-6R3
PD6001-7R3
4-20 mA output
PD6001-6R4
PD6001-7R4
4 relays
PD6001-6R5
PD6001-7R5
2 relays &4-20 mAoutput
PD6001-6R7
PD6001-7R7
4 relays & 4-20 mA output
SunBright Display Models
85-265 VAC
Model
12-24 VDC
Model
Options Installed
PD6001-6H0
PD6001-7H0
No options
PD6001-6H2
PD6001-7H2
2 relays
PD6001-6H3
PD6001-7H3
4-20 mA output
PD6001-6H4
PD6001-7H4
4 relays
PD6001-6H5
PD6001-7H5
2 relays &4-20 mAoutput
PD6001-6H7
PD6001-7H7
4 relays & 4-20 mA output
Accessories
Model
Description
PDA1002
DIN rail mounting kit for two devices
PDA1004
4 SPST (Form A) relays module
PDA1044
4 digital inputs & 4 digital outputs module
PDA1232
RS-232 serial adapter
PDA1485
RS-485 serial adapter
PDA7485-I
RS-232 to RS-485 isolated converter
PDA8008
USB Adapter
PDA8232-N
USB to RS-232 non-isolated converter
PDA8485-I
USB to RS-485 isolated converter
PDA-LH
Light / horn accessory
MOD-LH
Light / horn / enclosure modification
PDA2360
Plastic control stations series
PD659
Signal isolators, splitters, & conditioners
PD9501
Multi-function calibrator
PD9502
Low-cost signal generator
PDX6901
Snubber: 0.01 μF/470 Ω, 250 VAC
Enclosures
Series
Meters
Material
PDA2300
1-10
Plastic NEMA 4X
PDA2500
1-6
Plastic NEMA 4X
PDA2600
1-6
Stainless Steel NEMA 4X
PDA2700
1-6
Painted Steel NEMA 4
PDA2800
1-2
Plastic NEMA 4X
PDA3400
1-3
Plastic NEMA 4X
Need help selecting the right enclosure?
Go to www.predig.com/esu
Replacement Option Cards
Model
Options Installed
PD1102
2 relays
PD1103
4-20 mA output
PD1104
4 relays
PD1105
2 relays &4-20 mAoutput
PD1107
4 relays & 4-20 mA output

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
7
Light / Horn Accessories
PROVUMeter Shown in a PDA2301 Enclosure with MOD-LHRB1 Red Light / Horn and Button.
Meter & Enclosure Sold Separately. Assembly Required.
MOD-LH
Model
Description
MOD-LHRB1
Red Light / Horn and Button with
Holes Drilled in Enclosure(1)
MOD-LHGB1
Green Light / Horn and Button with
Holes Drilled in Enclosure(1)
MOD-LHYB1
Yellow Light / Horn and Button with
Holes Drilled in Enclosure(1)
MOD-LHBB1
Blue Light / Horn and Button with
Holes Drilled in Enclosure(1)
MOD-LHWB1
White Light / Horn and Button with
Holes Drilled in Enclosure(1)
MOD-LH5CB1
Light / Horn with User Choice of
Red, Green, Yellow, Blue or White
Light, Button, and Holes Drilled in
Enclosure(1)
Note:
1. This MOD supplies the Light / Horn and Button. The enclosure
comes pre-drilled with holes for Light / Horn and Button and the
user performs the installation and wiring. Controller and enclosure
are sold separately. The Light / Horn hole is in the back left corner
of the enclosure and the Button is centered on the cover of the
enclosure below the controller about an inch off the bottom of the
cover except on the PDA3400 series where it is mounted on the
side of the enclosure.
PDA-LH & PDA-BUTTON
Model
Description
PDA-LHR
Red Light / Horn
PDA-LHG
Green Light / Horn
PDA-LHY
Yellow Light / Horn
PDA-LHB
Blue Light / Horn
PDA-LHW
White Light / Horn
PDA-LHW
White Light / Horn
PDA-LH5C
Light / Horn with User Choice of
Red, Green, Yellow, Blue or White
Light
PDA-BUTTON1R
Red Button
PDA-BUTTON1G
Green Button
PDA-BUTTON1B
Blue Button

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
8
PDA2360 Control Stations
Model
Description
PDA2360-E
Emergency button
PDA2361-A
Ack button
PDA2361-B
Blank button
PDA2361-R
Reset button
PDA2361-T
Tare button
PDA2361-S
Stop button
PDA2361-Q
Silence button
PDA2362-AR
Ack and Reset buttons
PDA2362-BB
Two blank buttons
PDA2364-MRUE
Menu, right, up, enter buttons
Note: Control stations with one button may be connected directly to the
meter via the F4 terminal. A PDA1044 (4) digital inputs & (4) digital
outputs module is required to operate the control stations of more than
one button. See Remote Operation of Meter on page 19 for details.
Signal Splitter & Conditioner Accessories
Model
Description
PD659-1MA-1MA
Signal Isolator with One 4-20 mA
Input and One 4-20 mA Output
PD659-1MA-2MA
Signal Splitter with One 4-20 mA
Input and Two 4-20 mA Outputs
PD659-1V-1MA
Signal Conditioner with One 0-10
VDC Input and One 4-20 mA Output
PD659-1MA-1V
Signal Conditioner with One
4-20 mA Input and One 0-10 VDC
Output

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
9
Helpful Videos
Precision Digital's PROVUSeries is a powerful line of
1/8 DIN meters that boasts advanced functionality for
various applications. The following videos might be of
interest.
PROVUSeries Overview
Learn about all the meters in the PROVUSeries.
https://www.predig.com/videos/E4gmQrAeT8o
PROVUMulti-Pump Alternation
Learn how to use the PROVUas a pump controller.
https://www.predig.com/videos/PumpControl
PROVUFunction Keys Tutorial
Learn how the PROVU’s function keys increase the
utility of the PROVU.
https://www.predig.com/videos/WMBYKlavW-Q
Connect a PROVUto a PC Using
MeterView Pro
Learn how easy it is to use MeterView Pro software.
https://www.predig.com/videos/PC_Connect
Connect a 2-Wire 4-20 mA Transmitter to
a PROVU
Learn how to connect your transmitter to a PROVU.
https://www.predig.com/videos/4-
20_mA_Connections
MeterView Pro USB Programming
Software
Learn how easy it is to program a PROVUPD6000
process meter.
https://www.predig.com/videos/MVPro_SW

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
10
Specifications
Except where noted all specifications apply to
operation at +25°C.
General
Display
Line 1: 0.60" (15 mm) high, red LEDs
separated by feet and inches designations
Line 2: 0.46" (12 mm) high, red LEDs
6 digits each (-99999 to 999999), with lead
zero blanking
Feet & Inches
Range
-9FT11IN(15/16 or 7/8) to
99FT11IN(15/16 or 7/8)
Display
Intensity
Eight user selectable intensity levels.
Default value is six.
Display
Update Rate
5/second (200 ms)
LED Status
Indicators
See Front Panel Buttons and Status LED
Indicators on page 20 for details.
Overrange
Display flashes 999999
Underrange
Display flashes -99999
Display
Assignment
Display Line 1:
PV1, max/min, max & min, set points, or
Modbus input.
Display Line 2:
Same as Display Line 1; plus units, tag,
PV2, percent of PV1, PV1 level in feet &
unit/tag, or turned off.
Programming
Methods
Four front panelbuttons, digital inputs, PC
and MeterView Pro software, or Modbus
registers.
Noise Filter
Programmable from 2 to 199
(0 will disable filter)
Filter Bypass
Programmable from 0.1 to 99.9% of
calibrated span
Recalibration
All ranges are calibrated at the factory.
Recalibration is recommended at least
every 12 months.
Max/Min
Display
Max/min readings reached by the process are
stored until reset by the user or until power to
the meter isturned off.
Rounding
Select 1, 2, 5, 10, 20, 50, or 100
(e.g. rounding = 10,
actual value = 12.093,
secondary display = 12.090,
main display = 12FT1IN 1/16).
Password
Three programmable passwords restrict
modification of programmed settings.
Pass 1: Allows use of function keys and
digital inputs
Pass 2: Allows use of function keys, digital
inputs and editing set/reset points
Pass 3: Restricts all programming, function
keys, and digital inputs.
Power
Options
85-265VAC50/60Hz;90-265VDC,20Wmax;
12-24 VDC, 12-24 VAC, 15 W max.
Powered over USB for configuration only.
Non-Volatile
Memory
All programmed settings are stored in non-
volatile memory for a minimum of ten years
if power is lost.
Fuse
Required external fuse: UL Recognized,
5 A max, slow blow; up to 6 meters may
share one 5 A fuse
Normal Mode
Rejection
Greater than 60 dB at 50/60 Hz
Isolation
4 kV input/output-to-power line
500 V input-to-output or output-to-P+ supply
Overvoltage
Category
Installation Overvoltage Category II:
Local level with smaller transient
overvoltages than Installation Overvoltage
Category III.
Environmental
Operating temperature range:
-40 to 65°C (-40 to 149°F)
Storage temperature range:
-40 to 85°C (-40 to 185°F)
Relative humidity:
0 to 90% non-condensing
Connections
Removable screw terminal blocks accept
12 to 22 AWG wire, RJ45 for external
relays, digital I/O, and serial communication
adapters.
Enclosure
1/8 DIN, high impact plastic, UL 94V-0,
color: black
Front Panel
NEMA 4X, IP65
Mounting
1/8 DIN panel cutout required:
3.622" x 1.772" (92 mm x 45 mm)
Two panel mounting bracket assemblies
are provided.
Tightening
Torque
Screw terminal connectors: 5 lb-in
(0.56 Nm)
Overall
Dimensions
4.68" x 2.45" x 5.64"
(119 mm x 62 mm x 143 mm)
(W x H x D)
Weight
9.5 oz (269 g)
Warranty
3 years parts & labor. See Warranty
Information and Terms & Conditions on
www.predig.com for complete details.

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
11
Process Input
Inputs
Field selectable: 0-20, 4-20 mA
10 V (0-5, 1-5, 0-10 V)
Modbus PV (Slave)
Isolated
Transmitter
Power Supply
Terminals P+ & P-: 24 VDC 10%.
All models selectable for 24, 10, or 5 VDC
supply (internal jumper J4). 85-265 VAC
models rated @ 200 mA max, 12-24 VDC
powered models rated @ 100 mA max.
5 & 10 VDC supply rated @ 50 mA max.
Refer to Transmitter Supply Voltage
Selection (P+, P-) on page 16.
When the Light / Horn is powered by the
transmitter power supply, see MOD-LH
Light / Horn's transmitter power supply
specification in MOD-LH manual for
additional details. Light / Horn power not
available for 5 or 10 VDC supplies.
Accuracy
±0.03% of calibrated span ±1 count
Temperature
Drift
0.005% of calibrated span/C max from
0 to 65C ambient, 0.01% of calibrated
span/C max from -40 to 0C ambient
Input Signal
Conditioning
Linear or round horizontal tank volume
calculation
Multi-Point
Linearization
2 to 32 points for PV or PV1
2 to 8 points for PV2 (Dual-scale Level
feature)
Round
Horizontal
Tank
Diameter & Length: 999.999 inch or cm
calculates volume in gallons or liters
respectively.
Low-Height
Cutoff
0FT1IN(0/16 or 0/8) to 99FT11IN(15/16 or 7/8)
(0FT0IN(0/16 or 0/8) disables cutoff function)
Decimal Point
Up to five decimal places or none
(PV2 only): d.ddddd, d.dddd, d.ddd, d.dd, d.d,
or dddddd
Calibration
Range
Input Range
Minimum Span
Input 1 & 2
4-20 mA
0.15 mA
10 V
0.10 V
An error message will appear if the input 1
and input 2 signals are too close together.
Input
Impedance
Voltage ranges: greater than 500 k
Current ranges: 50 - 100 (depending on
internal resettable fuse impedance)
Input
Overload
Current input protected by an internal
resettable fuse, 30 VDC max. Fuse resets
automatically after fault is removed.
HART
Transparency
The meter does not interfere with existing
HART communications; it displays the
4-20 mA primary variable and it allows the
HART communications to pass through
without interruption. The meter is not
affected if a HART communicator is
connected to the loop. The meter does not
display secondary HART variables.
Relays
Rating
2 or 4 SPDT (Form C) internal and/or
4 SPST (Form A) external; rated 3 A
@ 30 VDC and 125/250 VAC resistive
load; 1/14 HP (≈50 W) @ 125/250 VAC for
inductive loads
Noise
Suppression
Noise suppression is recommended for
each relay contact switching inductive
loads. See Switching Inductive Loads on
page 18 for details.
Deadband
0-100% of span, user programmable
High or Low
Alarm
User may program any alarm for high or
low trip point. Unused alarm LEDs and
relays may be disabled (turn off).
Relay
Operation
•Automatic (non-latching) and/or
manual reset
•Latching (requires manual
acknowledge) with or without clear
•Pump alternation control (2-8 relays)
•Sampling (based on set point and time)
•Off (disable unused relays and enable
Interlock feature)
•Manual on/off control mode
Relay Reset
(Acknowledge)
User selectable via front panel button, F4
terminal at back of meter, external contact
closure on digital inputs, or through serial
communications.
Time Delay
0 to 999.9 seconds, on & off relay time
delays. Programmable and independent for
each relay
Fail-Safe
Operation
Programmable and independent for each
relay.
Note: Relay coil is energized in non-alarm
condition. In case of power failure, relay will
go to alarm state.
Auto
Initialization
When power is applied to the meter, relays
will reflect the state of the input to the meter.
Additional
Relays
An external module, model PDA1004, is
available to add 4 SPST 3 A relays to the
meter.

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
12
Isolated 4-20 mA Transmitter
Output
Output
Source
Process variable (PV), max, min, set points
1-8, Modbus input, or manual control mode
Scaling
Range
1.000 to 23.000 mA for any display range
Calibration
Factory calibrated:
4.000 to 20.000 = 4-20 mA output
Analog Out
Programming
23.000 mA maximum for all parameters:
Overrange, underrange, max, min, and
break
Accuracy
± 0.1% of span ± 0.004 mA
Temperature
Drift
0.4 µA/C max from 0 to 65C ambient,
0.8 µA/C max from -40 to 0C ambient
Note: Analog output drift is separate from
input drift.
Isolated
Transmitter
Power Supply
TerminalsI+& R:24VDC 10%. May be
used to power the 4-20 mA output or other
devices.
All models rated @ 40 mA max.
External Loop
Power Supply
35 VDC maximum
Output Loop
Resistance
Power supply
Minimum
Maximum
24 VDC
10 
700 
35 VDC
(external)
100 
1200 
Additional
4-20 mA
Outputs
The PD659-1MA-2MA can split the
optional 4-20 mA output into two isolated
4-20 mA outputs
0-10 VDC
Output
The PD659-1MA-1V can convert the
optional 4-20 mA output to a 0-10 VDC
output
USB Connection
Function
Programming only
Compatibility
USB 2.0 Standard, Compliant
Connector Type
Micro-B receptacle
Cable
USB A Male to Micro-B Cable
Driver
Microsoft®Windows®XP/Vista/7/8/10
Power
USB port provides power to the meter.
DO NOT apply AC or DC power to the
meter while the USB port is in use.
On-Board Digital Input (F4)
Function
Remote operation of front-panel buttons,
acknowledge/reset relays, reset max/min
values. See Function Keys & Digital I/O
Available Settings on page 43 for a
complete list of capabilities.
Contacts
3.3 VDC on contact. Connect normally
open contacts across F4 to COM
Logic Levels
Logic High: 3 to 5 VDC
Logic Low: 0 to 1.25 VDC
Additional I/O
Up to 2 external modules, model PDA1044
with 4 digital inputs and 4 digital outputs
each can be added.
Modbus®RTU Serial
Communications
Slave Id
1 –247 (Meter address)
Baud Rate
300 –19,200 bps
Transmit
Time Delay
Programmable between 0 and 199 ms
Data
8 bit (1 start bit, 1 or 2 stop bits)
Parity
Even, Odd, or None with 1 or 2 stop bits
Byte-To-Byte
Timeout
0.01 –2.54 second
Turn Around
Delay
Less than 2 ms (fixed)
Note: Refer to the PROVUModbus Register Tables located
at www.predig.com for details.
MeterView Pro Software
Availability
Download directly from meter or from
www.predig.com/download_software
System
Requirements
Microsoft®Windows®XP/Vista/7/8/10
Communications
USB 2.0 (for programming only)
(Standard USB A to Micro USB B)
RS-232 adapter, RS-485 adapter and
RS-485 to USB converter
(programming, monitoring, and data
logging)
Configuration
Configure meters one at a time
Power
USB port provides power to the meter.
DO NOT apply AC or DC power to the
meter while the USB port is in use.

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
13
Compliance Information
Safety
UL & C-UL Listed
USA & Canada
UL 508 Industrial Control Equipment
UL File Number
E160849
Front Panel
UL Type 4X, NEMA 4X, IP65; panel
gasket provided
Low Voltage
Directive
EN 61010-1
Safety requirements for measurement,
control, and laboratory use
Electromagnetic Compatibility
Emissions
EN 55022
Class A ITE emissions requirements
Radiated
Emissions
Class A
AC Mains
Conducted
Emissions
Class A
Immunity
EN 61326-1
Measurement, control, and laboratory
equipment
EN 61000-6-2
EMC heavy industrial generic immunity
standard
RFI - Amplitude
Modulated
80 -1000 MHz 10 V/m 80% AM (1 kHz)
1.4 - 2.0 GHz 3 V/m 80% AM (1 kHz)
2.0 - 2.7 GHz 1 V/m 80% AM (1 kHz)
Electrical Fast
Transients
±2kV AC mains, ±1kV other
Electrostatic
Discharge
±4kV contact, ±8kV air
RFI -
Conducted
10V, 0.15-80 MHz, 1kHz 80% AM
AC Surge
±2kV Common, ±1kV Differential
Surge
1KV (CM)
Power-
Frequency
Magnetic Field
30 A/m 70%V for 0.5 period
Voltage Dips
40%V for 5 & 50 periods
70%V for 25 periods
Voltage
Interruptions
<5%V for 250 periods
Note:
Testing was conducted on meters installed through the
covers of grounded metal enclosures with cable shields
grounded at the point of entry representing installations
designed to optimize EMC performance.
EU Declaration of
Conformity
EU Declaration of Conformity is available in the
Documentation CD provided with the product under
the EU DoC menu.
Safety Information
•Read complete instructions prior to installation
and operation of the meter.
•Risk of electric shock or personal injury.
•Hazardous voltages exist within enclosure.
Installation and service should be performed only
by trained service personnel.
Installation
There is no need to remove the meter from its
case to complete the installation, wiring, and
setup of the meter for most applications.
Instructions are provided for changing the
transmitter power supply to output 5 or 10 VDC
instead of 24 VDC. See Figure 5. Transmitter
Supply Voltage Selection on page 16.
Unpacking
Remove the meter from box. Inspect the
packaging and contents for damage. Report
damages, if any, to the carrier.
If any part is missing or the meter malfunctions,
please contact your supplier or the factory for
assistance.

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
14
Panel Mounting Instructions
•Prepare a standard 1/8 DIN panel cutout -
3.622" x 1.772" (92 mm x 45 mm). Refer to
Figure 1. 1/8 DIN Panel Cutout Dimensions
below for more details.
•Clearance: allow at least 6.0" (152 mm) behind
the panel for wiring.
•Panel thickness: 0.04" - 0.25" (1.0 mm - 6.4 mm).
Recommended minimum panel thickness to
maintain Type 4X rating: 0.06" (1.5 mm) steel
panel, 0.16" (4.1 mm) plastic panel.
•Remove the two mounting brackets provided with
the meter (back-off the two screws so that there is
¼" (6.4 mm) or less through the bracket. Slide the
bracket toward the front of the case and remove).
•Insert meter into the panel cutout.
•Install mounting brackets and tighten the screws
against the panel. To achieve a proper seal,
tighten the mounting bracket screws evenly until
meter is snug to the panel along its short side.
DO NOT OVER TIGHTEN, as the rear of the
panel may be damaged.
Figure 1. 1/8 DIN Panel Cutout Dimensions
DO NOT apply AC or DC power to the meter when using the
USB connection.
Figure 2. Panel Mounting Details
Mounting Dimensions
Figure 3. Meter Dimensions - Side View
Figure 4. Meter Dimensions - Top View
NO NC NC C NO C
NO NC NC C NO C+ -R
3.622" (92 mm)
1.772"
(45mm)
Panel Cutout
to DIN 43700
Square Corners to 0.060"
(1.5mm) Max Radius
A
B
Tolerances:
A: +0.032 (+0.8mm)
-0.000 (-0.0mm)
B: +0.024 (+0.6mm)
-0.000 (-0.0mm)

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
15
Installation Overview
We recommend the following sequence for getting the
meter into service:
1. DO NOT apply AC or DC power to the meter.
2. Connect the meter to the PC with the USB cable
provided. DO NOT use a different USB cable.
3. If MeterView Pro (MVPro) is already installed in
your computer, then the program will launch
automatically in most systems. If the program
does not start automatically, double-click on the
MVPro icon.
4. If MVPro is not installed, follow the instructions
provided below.
5. Use MVPro to configure the meter for your
application.
6. Disconnect the USB cable from the meter.
7. Apply power and signal and check operation of
the meter.
8. Install the meter and put into service.
9. Make any programming adjustments using the
front panel buttons.
MeterView Pro Software
The easiest and quickest way to program your PROVU
meter is to use the FREE MeterView Pro
programming software. This software is loaded into
the meter and connects and installs directly to your
PC with the USB cable provided. DO NOT use a
different USB cable. We recommend that the first
thing you do after taking the meter out of the box is
connect the PROVUto your PC with the provided USB
cable. DO NOT apply AC or DC power to the meter
while your PC is connected to the meter as it will
disrupt the USB connection. It is not necessary to
apply an input signal.
MeterView Pro programming software is intuitive, and
most customers can get their meter programmed as
they like without even looking in the manual.
Watch Meterview Pro Software Video at
www.predig.com/meterviewpro
MeterView Pro Installation
1. Connect one end of the provided USB cable
to the meter and the other end to the
computer. The computer will automatically
install the driver software it needs to talk to
the meter. Follow the on-screen instructions
and allow sufficient time for the process to
complete. This can take a few minutes. If the
process is interrupted, then it could leave the
system in an unstable condition.
•Only one meter may be connected at a time.
Attaching multiple meters will cause a conflict
with the meter software.
•DO NOT apply AC or DC power to the meter
when using the USB connection.
2. Once the driver is installed, an AutoPlay
dialog should appear for the drive
“MAINSTAL.” Click “Open folder to view
files.”
If the computer does not display an AutoPlay
dialog for the drive “MAINSTAL,” you should
open My Computer and double-click on the
drive labeled “MAINSTAL.”
3. Double-click on the file named “MAStart.”
The program will open a few windows and
install two programs on your computer.
Simply follow the on-screen instructions until
you see one of the dialogs below. If you
receive a “User Account Control” warning,
click “Yes.”
4. If there is an update available, click the
“Update” button to install the new version.
Otherwise, click “Configure” to begin
programming your meter.
Note: If you decide to update your MeterView Pro
software, once the installation has completed, you
will be asked if you want to update the setup files
located on the meter itself. This way, you will
always have the most current version on the meter
for future installs.
•DO NOT unplug the meter while the new
installation files are being written to it. The meter
will display uwrite during the process and you
will receive an on-screen notification once the
process is complete.

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
16
Transmitter Supply Voltage
Selection (P+, P-)
All meters, including models equipped with the
12-24 VDC power option, are shipped from the
factory configured to provide 24 VDC power for
the transmitter or sensor.
If the transmitter requires 5 or 10 VDC excitation,
the internal jumper J4 must be configured
accordingly.
To access the voltage selection jumper:
1. Remove all the wiring connectors.
2. Unscrew the back cover.
3. Slide out the back cover by about 1
inch.
4. Configure the J4 jumper, located behind
the input signal connector, for the
desired excitation voltage as shown.
Figure 5. Transmitter Supply Voltage Selection
Connections
All connections are made to removable screw
terminal connectors located at the rear of the
meter.
•Use copper wire with 60°C or 60/75°C insulation
for all line voltage connections. Observe all safety
regulations. Electrical wiring should be performed
in accordance with all applicable national, state,
and local codes to prevent damage to the meter
and ensure personnel safety.
Connectors Labeling
The connectors’ label, affixed to the meter, shows the
location of all connectors available with requested
configuration.
Note: ## on the following figures refers to power and
display options. (Example: PD6001-6H5)
Figure 6. PD6001-##0 Connectors Label
Figure 7. PD6001-##2 Connectors Label
Figure 8. PD6001-##3 Connectors Label
Figure 9. PD6001-##4 Connectors Label
Figure 10. PD6001-##5 Connectors Label
Figure 11. PD6001-##7 Connectors Label
•DO NOT connect any equipment other than
Precision Digital’s expansion modules, cables, or
meters to the RJ45 M LINK connector. Otherwise
damage will occur to the equipment and the
meter.
POWER
+-
SIGNAL
M-LINK
123 4 5 6 7 8
21
P- COMP+ V+ mA+
3412 5
F4
6
POWER
+-
SIGNAL
M-LINK
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
P- COMP+ V+ mA+
3412 5
F4
6
R
I- I+
MA OUT
1
32
POWER
+-
SIGNAL
M-LINK
123 4 5 6 7 8
21
24 V
P- COMP+ V+ mA+
3412 5
F4
6
POWER
+-
SIGNAL
M-LINK
CNONO NC NC C
RELAY4 RELAY3
4365 2 1
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
P- COMP+ V+ mA+
3412 5
F4
6
R
I- I+
MA OUT
1
32
POWER
+-
SIGNAL
M-LINK
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
24 V
P- COMP+ V+ mA+
3412 5
F4
6
R
I- I+
MA OUT
1
32
POWER
+-
SIGNAL
M-LINK
CNONO NC NC C
RELAY4 RELAY3
4365 2 1
CNONO NC NC C
RELAY2 RELAY1
4365 21
123 4 5 6 7 8
21
24 V
P- COMP+ V+ mA+
3412 5
F4
6

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
17
Power Connections
Power connections are made to a two-terminal
connector labeled POWER. The meter will operate
regardless of DC polarity connection. The + and -
symbols are only a suggested wiring convention. There
are separate meters for AC and DC power. See
Ordering Information on page 6for details.
Figure 12. Power Connections
Signal Connections
Signal connections are made to a six-terminal
connector labeled SIGNAL. The COM (common)
terminal is the return for the
4-20 mA and the 10 V input signals.
Current (mA) Connections
The following figures show examples of current
connections.
There are no switches or jumpers to set up for current
inputs. Setup and programming is performed through
the front panel buttons or MeterView Pro software.
Figure 13. Transmitter Powered by Internal Supply
Figure 14. Transmitter Powered by External
Supply or Self-Powered
The current input is protected against current
overload by an internal resettable fuse. The display
may or may not show a fault condition depending on
the nature of the overload.
The fuse limits the current to a safe level when it
detects a fault condition, and automatically resets
itself when the fault condition is removed.
Voltage (V) Connections
The following figures show examples of voltage
connections.
There are no switches or jumpers to set up for voltage
inputs. Setup and programming is performed through
the front panel buttons or MeterView Pro software.
Figure 15. Voltage Input Connections
The meter is capable of accepting any voltage from -
10 VDC to +10 VDC.
Modbus RTU Serial
Communications
Serial communications connection is made to an
RJ45 connector labeled M-LINK. For interfacing to the
PROVU, use the PDA1232 for RS-232 or the PDA1485
for RS-485. The same port is used for interfacing with
all expansion modules (e.g. external relays, digital
I/O).
Relay Connections
Relay connections are made to two six-terminal
connectors labeled RELAY1 –RELAY4. Each relay’s
C terminal is common only to the normally open (NO)
and normally closed (NC) contacts of the
corresponding relay. The relays’ C terminals should
not be confused with the COM (common) terminal of
the INPUT SIGNAL connector.
Figure 16. Relay Connections
AC or DC
POWER
Required External Fuse:
5 A max, 250 V Slow Blow
POWER
+-
CNONO NC NC C
RELAY4 RELAY3
4 36 5 2 1
CNONO NC NC C
RELAY2 RELAY1
4 36 5 2 1

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
18
Switching Inductive Loads
The use of suppressors (snubbers) is strongly
recommended when switching inductive loads to
prevent disrupting the microprocessor’s operation.
The suppressors also prolong the life of the relay
contacts. Suppression can be obtained with resistor-
capacitor (RC) networks assembled by the user or
purchased as complete assemblies. Refer to the
following circuits for RC network assembly and
installation:
Figure 17. AC and DC Loads Protection
Choose R and C as follows:
R: 0.5 to 1 Ωfor each volt across the contacts
C: 0.5 to 1 µF for each amp through closed contacts
Notes:
1. Use capacitors rated for 250 VAC.
2. RC networks may affect load release time of
solenoid loads. Check to confirm proper
operation.
3. Install the RC network at the meter's relay screw
terminals. An RC network may also be installed
across the load. Experiment for best results.
Use a diode with a reverse breakdown voltage two to three
times the circuit voltage and forward current at least as large
as the load current.
Figure 18. Low Voltage DC Loads Protection
RC Networks Available from
Precision Digital
RC networks are available from Precision Digital and
should be applied to each relay contact switching an
inductive load. Part number: PDX6901.
Note: Relays are de-rated to 1/14th HP (50 watts)
with an inductive load.
F4 Digital Input Connections
A digital input, F4, is standard on the meter. This
digital input should be connected with a normally
open contact across F4 and COM, or with an active
low signal applied to F4. It can be used for remote
operation of front-panel buttons, to acknowledge/reset
relays, or to reset max/min values. See Function Keys
& Digital I/O Available Settings on page 43 for a
complete list of capabilities.
Figure 19. F4 Digital Input Connections
4-20 mA Output Connections
Connections for the 4-20 mA transmitter output are
made to the connector terminals labeled mA OUT.
The 4-20 mA output may be powered internally or
from an external power supply.
Figure 20. 4-20 mA Output Connections
Analog Output Power Supply
The internal 24 VDC power supply powering the
analog output may be used to power other devices, if
the analog output is not used. The I+ terminal is the
+24 V and the R terminal is the return.
Figure 21. Analog Output Supply Powering Other
Devices
C
R
C
R
P- COMP+ V+ mA+
3412 5
F4
6
4-20 mA Input
Remote Display, PLC,
Chart Recorder, Etc.
-
+
RI- I+ 132
RELAY1 mA OUT
24 V
12-35 VDC
Power
Supply
+
4-20 mA
Input Meter
-+
RI- I+ 132
RELAY1
321
-
24 V
mA OUT
Internal Power Supply
and Analog Output
321
Active Output Loop Passive Output Loop
RI- I+
132
24 VDC
Powered
Device
24 V
+-

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
19
External Relays & Digital I/O
Connections
The relay and the digital I/O expansion modules
PDA1004 & PDA1044 are connected to the meter
using a CAT5 cable provided with each module. The
two RJ45 connectors on the expansion modules are
identical and interchangeable; they are used to
connect additional modules to the system.
Note: The jumper located between the RJ45
connectors of the PDA1044 must be removed
on the second digital I/O module in order for the
system to recognize it as module #2.
•DO NOT connect or disconnect the expansion
modules with the power on! More detailed
instructions are provided with each optional
expansion module.
Figure 22. Expansion Module & DIN Rail Mounting
Kit
Figure 23. External Relays Module Connections
Figure 24. Digital I/O Module Connections
Remote Operation of Meter
The meter can be operated via the front panel push
buttons or a remote control station using the
PDA1044 Digital I/O module as illustrated in Figure
25. Meter to Control Station Connection.
Figure 25. Meter to Control Station Connection
Interlock Relay Feature
As the name implies, the interlock relay feature
reassigns one, or more, alarm/control relays for use
as interlock relay(s). Interlock contact(s) are wired to
digital input(s) and activate the interlock relay. This
feature is enabled by configuring the relay, and the
corresponding digital input(s), see Setting Up the
Interlock Relay (Force On) Feature on page 35.
In the example below, an Interlock Contact switch is
connected to a digital input, which will be used to
force on (energize) the Interlock Relay. The Interlock
Relay and the Control Relay are connected in series
with the load.
•When the Interlock Contact is closed (safe), the
Interlock Relay energizes, allowing power to flow
to the Control Relay; the corresponding front
panel LED is on.
•When the Interlock Contact is open, the
corresponding front panel LED flashes (locked
out), the Interlock Relay is de-energized,
preventing power from flowing to the Control
Relay and the load.
Figure 26. Interlock Connections
1 2
RLY5 RLY6 RLY7 RLY8
3 4 5 6 7 8
NO CNO CNO CNO C
1 2 3 4 5 6
+5 I1 I2 I3 I4 O1
7 8
O2 O3
910
O4 G
DI 1-4 DO 1-4
5 VDC GND

PROVU™PD6001 Analog Input Feet & Inches Meter
Instruction Manual
20
Setup and Programming
There is no need to recalibrate the meter
when first received from the factory.
The meter is factory calibrated prior to
shipment for milliamps and volts with
calibration equipment that is certified to
NIST standards.
Overview
There are no jumpers to set for the meter input
selection.
Setup and programming is done using MeterView Pro
or through the front panel buttons.
After power and input signal connections have been
completed and verified, apply power to the meter.
Front Panel Buttons and Status
LED Indicators
Button Symbol
Description
Menu
Right arrow/F1
Up arrow/F2
Enter/F3
LED
State
Indication
1-8
Steady
Alarm condition based on set
and reset points, independent
of relay status in certain
configurations. (Available on all
meter configurations, including
those without relays installed)
1-8
Flashing
Relay interlock switch open
1-8 & M
Flashing
Relay in manual control mode
T
Flashing
Meter in Tare mode
M
Flashing
Analog ouput in manual control
mode
8
Steady
Eighths of an inch
16
Steady
Sixteenths of an inch
Symbol
Description
FT
Feet value
IN
Inches value
--
Designation separators
•Press the Menu button to enter or exit the
Programming Mode at any time.
•Press the Right arrow button to move to the next
digit during digit or decimal point programming.
•Press or hold the Up arrow button to scroll
through the menus, decimal point, or to
increment the value of a digit.
•Press the Enter button to access a menu or to
accept a setting.
•Press and hold the Menu button for three
seconds to access the advanced features of the
meter.