Precision SB4500PRC User manual

Parts
No
2877
2908B
2908GY
2887
2887G
2554
2888B
2888GY
2546B
2546G
2900B
2900GY
3190
2441
2614
2576
4466
1868
6129
2582
1270
2828
1042
3333
1646
1817
6214
2174
2879A
2978
2973
2983
2976
2984
1807
2977
2970
2971
3855
2975
2979
2906
Description
Hopper
Wrap-Around Support (Black)
Wrap-Around Support (Gray)
Leg Stand (Black)
Leg Stand (Gray)
Foam Handle Cover
Handle (Black)
Handle (Gray)
Cross Brace (Black)
Cross Brace (Gray)
Support (Black)
Support (Gray)
Wheel
Control Cable
Spinner Disc
3/16” x 2” Cotter Pin
1/4 x 3-1/2 Hex Head Bolt
1/4 x 2-1/4 Carriage Bolt
1/4 x 1-1/2 Hex Head Bolt
Tube Cap
1/4 Hex Nut
Wing Nut
Hitch Pin Clip
5/8 Retaining Ring
5/8 Washer
1/4 Flat Washer
5/8 Wheel Bushing
3/8 Retaining Ring
Spinner Shaft Assembly
7/8 Spring Clamp
3/8 Nylon Bushing
1/4 - 28 Grease Zerk
Rear Gear Case Housing
1/4 - 28 x 1/2 Long Hex Bolt
1/4 Lock Washer
15/16 Spring Clamp
5/8 Nylon Bushing
Drive Gear
Axle
Front Gear Case Housing
3/16 x 1-1/4 Split Pin
Rain Cover (Not Shown)
Qty
1
1
1
1
1
1
2
2
1
1
1
4
3
2
2
6
3
1
1
3
4
2
1
1
1
3
1
1
1
1
2
2
1
1
1
1
1
SB4500PRC & SB4500PRCGY
BROADCAST SPREADERS
06/05
MADE IN
USA
Ref
No
1
2
**
3
**
4
5
**
6
**
7
**
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
**
12
3
See Below
For Parts
45
6
7
8
9
11 12 13 14 15
17
18
19 20 21 22
23
Gear Case Components
16
10
24
25
26 27
28
29
30 31
32
32
31
33
34
35
36
3837
Parts referenced with ** have two color options.
Retain for future reference
CUSTOMER SUPPORT
At Precision Products, Inc.
delivering quality, value and
outstanding service is our goal.
However, sometimes parts do
become damaged or lost during
transport from our facilities to
the store. If you have any
problems, please do not
return this merchandise to the
store. Call us and we will take
care of any problem you may
have with this unit.
Phone [phone] Ext. 204
TIP: Many of these hardware
parts can be purchased at your
local hardware store.
HOW TO ORDER
REPLACEMENT PARTS:
When ordering parts always
give model number, part
number and part description.
Send To: Parts Division
316 Limit Street
Lincoln, IL 62656
Phone [phone]
[phone] Ext. 204
FAX [phone]
www.precisionprodinc.com

LIMITED WARRANTY
This unit is warranted against defects in materials and workmanship to the
original purchaser, under normal use and service, for a period of ninety (90)
days from date of sale. During the Warranty Period, we will repair or replace
at our option free of charge to the original purchaser, any part of the Unit
that our examination shows to be defective in workmanship or materials.
This Warranty Does Not apply to damage caused by transit, misuse, abuse,
neglect, accident, normal wear, or alterations by unauthorized persons.
USING YOUR SB4500PRC & SB4500PRCGY BROADCAST SPREADER
STEP 1
Un-fold Handle
and tighten Wing
Nuts on the Handle.
FOR STORAGE
Loosen the two Wing
Nuts and fold handle
under hopper.
MAINTENANCE INSTRUCTIONS
Numbered Settings
Control Lever
Calibration
Indicator button
ON -- Push the Control Lever
forward until it stops
against Calibration Button.
OFF -- Pull Control Lever back
until it stops.
USING YOUR SPREADERS CONTROLLER
Settings are made by pushing down on the Calibration Indicator
button and setting to the desired number on the Control Cable
assembly.
SEE APPLICATION CHART FOR SETTING INFORMATION.
Recommended operating weight – 90 lbs.
Wing Nuts
Handle
folded down
1. Always have the control lever in OFF position
before filling the hopper.
2. Always push the spreader forward to operate;
do not pull backwards.
3. Start walking forward before pushing the control
lever to the ON position. Pull the control lever to
OFF position before stopping or turning.
DO NOT allow spreader to sit stationary with
material in the hopper and control lever in the
ON position.
4. Hold the handle at a height that will keep the
hopper level.
5. Push the spreader at a steady, brisk pace (approximately
3 mph is recommended).
6. To avoid misses or striping, space each pass across the
lawn so approximately 20% of the spread width overlaps
onto the previous pass. This provides a “feathered” over-
lap to even out distribution over the width of the spread.
CAUTION: care must be taken with any weed killer,
pesticide, or combination product. They can be harmful
to other plant life in the yard.
BROADCAST SPREADER OPERATION
1. Empty hopper after each use. Do not store spreader
with material left in hopper.
2. Wash spreader thoroughly and wipe dry.
3. Lubricate all moving parts. Use a grease gun to apply
grease to the gearbox assembly. CAUTION: Use a
reasonable amount of grease. DO NOT pack
gearbox full of grease. Apply oil to spinner shaft
(including area shaft extends through hopper), slide
plate and where the spinner shaft and axle extend
through the gearbox.