Premier Farnell Akron Brass Extenda-Lite Electric Rewind Cord... User manual

Don't Be Afraid Of The Dark...
WARRANTY AND DISCLAIMER: We warrant Akron Brass products for a period of five (5) years after purchase against defects in materials or workmanship. Akron Brass will repair or replace product
which fails to satisfy this warranty. Repair or replacement shall be at the discretion of Akron Brass. Products must be promptly returned to Akron Brass for warranty service.
We will not be responsible for: wear and tear; any improper installation, use, maintenance or storage; negligence of the owner or user; repair or modification after delivery; damage; failure to follow our
instructionsor recommendations;oranythingelsebeyondour control.WEMAKENOWARRANTIES,EXPRESSORIMPLIED,OTHERTHANTHOSINCLUDEDIN THISWARRANTYSTATEMENT,AND
WEDISCLAIMANYIMPLIEDWARRANTYOFMERCHANTABILITYOR FITNESSFORANYPARTICULARPURPOSE.Further,wewillnotberesponsiblefor any consequential,incidentalorindirect
damage (included, but not limited to, any loss or profits) from any cause whatsoever. No person has authority to change this warranty.
PHONE: [phone] or 800.228.1161 FAX:[phone] or 800.531.7335 www.akronbrass.com
A Premier Farnell Company
MOUNTING INSTRUCTIONS FOR
ELECTRIC REWIND CORD REEL
1- Unpack the shipping box. Inside you will find an Extenda-Lite Electric Rewind Cord Reel that is totally prewired.
2- Inspect the box and all items inside for damage. Report any damage to the delivering carrier immediately. If there is any
damage, save the box and all packing materials.
3- Before doing any wiring make certain the power cord to the cord reel is completely disconnected from its
junction box or power supply. Have a Licensed Electrician do all wiring.
4- If the hub is going to remain on the frame during installation please skip to line13.
5- Remove the six screws that attaches the upper guard to the frame and lower guard and set upper guard aside.
6- Remove the four screws that attaches the lower guard to the frame and set lower guard aside.
7- Loosen the four bolts that attach the motor to the frame.
8- Adjust motor to put slack in the chain and remove chain from small sprocket on motor.
9- Remove the 4 bolts that secures the isolator mounts on either side of the disks.
10- Remove hub/disk assembly and set aside.
11- If the motor is going to remain on the frame during installation please skip to line 13.
12- Remove the four bolts that attach the motor to the frame and set motor aside.
13- Properly orientate frame (Remember motor can be mounted on left or right side by simply rotating hub/disk assembly
before reassembly.
14- Holes have been predrilled along the base of the frame for mounting purposes. Mount frame level.
15- After frame is mounted attach motor back to frame. (If removed in step 10)
16- Attach hub/disk assembly to frame (If removed in step 3) and reattach chain guards.
17- Attach cord to the 1' pigtail coming out of the hub - Black to Black, White to White, Green to Green and
Red to Red (if 4 wire) See other side for detailed instructions. Please note 4 wire is not available on
the ERWC-16-6.
18- Run wire from 12 volt power source to relay to circuit breaker to switch to motor. (Per the manufacturer's
instructions the solenoid should be mounted as close as possible to the battery as possible.)
19- Run wire from AC power source to gang box on side of reel. Depending on how reel was specified the gang box will
either be direct wired to reel or there will be a 4' pigtail between gang box and frame.
20- Insert wire from power source through side of gang box and attach to the cooresponding slot on terminal block -
Black to Black, White to White, Green to Green and Red to Red (if 4 wire). Please note 4 wire is not available on the
ERWC-16-6.
Page 33

Don't Be Afraid Of The Dark...
WARRANTY AND DISCLAIMER: We warrant Akron Brass products for a period of five (5) years after purchase against defects in materials or workmanship. Akron Brass will repair or replace product
which fails to satisfy this warranty. Repair or replacement shall be at the discretion of Akron Brass. Products must be promptly returned to Akron Brass for warranty service.
We will not be responsible for: wear and tear; any improper installation, use, maintenance or storage; negligence of the owner or user; repair or modification after delivery; damage; failure to follow our
instructionsor recommendations;or anythingelsebeyondour control.WE MAKENO WARRANTIES,EXPRESSORIMPLIED,OTHERTHANTHOSINCLUDEDIN THIS WARRANTYSTATEMENT,AND
WEDISCLAIMANYIMPLIEDWARRANTYOFMERCHANTABILITYOR FITNESSFORANYPARTICULARPURPOSE.Further,wewillnotberesponsiblefor any consequential,incidentalorindirect
damage (included, but not limited to, any loss or profits) from any cause whatsoever. No person has authority to change this warranty.
PHONE: [phone] or 800.228.1161 FAX:[phone] or 800.531.7335 www.akronbrass.com
A Premier Farnell Company
17a
There will be three (four) wires coming out of
the center hub, Black (hot), (Red if a 4 wire
reel is purchased - Hot) White (common) and
Green (ground) and each is equipped with a
10-12 yellow butt connector attached to each
wire.
17b
On YOUR CORD SET prepare one end of your
cord by taking about 4" of the outside insulation
off making sure that you do not cut through or
into the three inside wires. Remove inside
fillers, leaving three number 10 or 12 wires.
17c 17d
Cut back the ends to match the offset on
the wires from the cord reel hub. Now
strip the insulation off the three (four)
wires and twist the ends so there are no
loose strands.
Slip your prepared cord set end through
the rubber coated cable clamp and slide
the 6" piece of shrink tubing over your cord
set end.
Connect the Black, White and Green
wires from your cord set to the three
matching colored wires exiting the
cord reel's center hub.(Red if a 4
wire reel is purchased.) Hand crimp
each connection with heavy duty wire
crimps designed for crimping. Make
sure that there are no loose wires or
wire strands around the butt
connectors.
17e 17f
Slide the shrink tube down your cord
set wire and over the three butt
connectors to the reel hub.
17g 17h
With a heat gun carefully shrink the
black tube around both wires until
tight. Do Not burn the reel disk or
wire connections or melt the center
hub of the reel with your heat source.
Tighten up the cable clamp. The
clamp is to be tight on your cord set
end ahead of the butt connectors.
Wiring of the hub is the same as wiring the portable reels
Page 34