premiere XC-1000 User manual

Centrifuge
Model XC-1000
Operating Manual
Before using this product, please read this manual carefully to learn about the available
features to obtain the best results of this equipment.
Warning:To prevent fire or shock hazard, do not expose this unit to rain or moisture. Unless
labeled otherwise, this equipment should be used with AC 110V 60Hz in the USA or Canada.
220V 50Hz available as Model No. XC-1000-220
Caution: No user-serviceable parts inside. Refer servicing to qualified service personnel

1
1.1 Table of Contents
Section
•Table of Contents Page 1
•Safety Page 2
•Contents/Accessories Page 3
•Specifications Page 4
•Notes of Operations Page 5
•Control Panel/Setup Page 6
•Operations Page 7
•Warranty Page 8

2
2.1 Safety
Before using the centrifuge, please read this instruction manual carefully. Incorrect or
inappropriate use may result in equipment damage or personal injury!
This centrifuge is designed for clinical medicine, biology, genetic engineering, immunology,
etc.
When the centrifuge is running (rotor is spinning), Please keep an area of about 12 inches
around the centrifuge clear while operating it and ensure nothing is blocking the vents.
To avoid injury to personnel and or separated samples inside the unit; do not use the
following materials in the centrifuge:
•Flammable and explosive materials
•Strong chemical materials
•Toxic or radioactive materials

3
3.1 Contents
Number
Name
Qty
Note
1
Centrifuge
1set
2 Rotor (included)
Capacity =< 10-15mL x 6 tube holders 12pc
(six included inside unit &
six extra)
3 Black silicone tube cushions 6pc
4 Fuse 1pc 4 AMP
5
Operating manual
1pc
Upon receipt, please examine the package, if there's anything wrong, please
kindly contact your dealer promptly.
3.2 Accessories
If you need optional auxiliary parts, please contact our company or authorized dealers.
Item
#01 Description
Number of pieces Image
XC-06
Replacement tube
holders
Set of 6 pcs

4
4.1 Specifications
Function/ Parameter
Technical Data
Environment of use
•Clean, dry and flat surface
•Stable work surface
•Altitude:
•Relative humidity:≤80%
Ambient Temperature •+5°C~-40°C
Applicable Voltage •AC110V 60Hz or 220V 50Hz
Setting Time Range •1~60min
Maximum RPM •4000 r/min
Maximum relative centrifugal
force (RCF) •1790xg
Rotor Length •5 cm
Radius •10 cm
Maximum capacity •15mL x 6
Noise (maximum speed) •≤70dB
Dimensions (machine) •11 x 11.5 x 10 in. (28 x 29 x 25 cm.)
Net Weight •9 lbs
Dimensions (package) •12 x 12 x 11 in. (32 x 32 x 28 cm.)
Gross Weight •11 lbs

5
5.1 Notes of Operation
● Ensure the rotor is tightened before running the centrifuge.
● Do not open the lid while the rotor is spinning. Allow centrifuge to come to a complete
stop before attempting to open lid and remove specimen tubes.
● Use only with accessories provided or parts designed specifically for use with this model.
● Do not use centrifuge when the door is open.
● Make sure the specimen tubes are equal and balanced. (Unbalanced tubes will cause the
machine to shake and not produce a smooth spinning motion).
● Before use check rotor. Cease use if there is obvious corrosion or damage signs on the
rotor.

6
6.1 Control Panel
Control Panel
Time LED：Time in min
+ -：increase/decrease time
On/Off：run/stop
6.2 Setup
1. Open box and remove centrifuge from packaging
2. Place centrifuge onto flat surface
3. Open lid and remove foam packaging inside
4. Plug Power cord from back of unit into power supply, unit will power up and your
centrifuge is ready for use.

7
7.1 Operations
Time Adjustment
1. Push the “+” or “-” button to adjust the time setting. To increase the run time push the
“+” button until desired time reached or maximum of 60 minutes. (See section 6.1).
To decrease the run time push the “-” button until desired time reached or minimum
of 1 min. (See section 6.1). If the numbers under “TIME LED” are not Lite, make
sure power cord is completely plugged into socket.
Spinning Centrifuge
2. Insert the centrifuge tubes in a manner that will balance the specimen tubes’ weight.
Always insert an even number of tubes on opposite sides of the rotor with
approximately the same amount of specimen in each tube.
Now that the desired time is selected, you can now run your samples.
1. Make sure lid is closed and locked.
2. Press the “On/Off” button, and centrifuge will begin spinning.
3. After the centrifuge has run for the programmed amount of time unit will begin to
decelerate and come to a complete stop. Please note that the lid should never be
opened until centrifuge has come to a complete stop.
Note
This centrifuge lid is designed to automatically stop when the lid is open. If you have any
problems operating the centrifuge, please contact your dealer or authorized provider.