SCHOTT KL 1500 HAL User manual

KL 1500 HAL
KL 1500 H
User Manual
Distribution in the UK & Ireland
Lambda Photometrics Limited
Lambda House Batford Mill
Harpenden Herts AL5 5BZ
United Kingdom
E: [email protected]
W: www.lambdaphoto.co.uk
T: [phone]
F: [phone]

KL 1500 HAL / KL 1500 H - Operating instructions
1/15
Operating instructions
KL 1500 HAL / KL 1500 H*
Status: March 2016
*different name KL1500H possible. In this operating instructions for the sake of simplicity, only the KL 1500
HAL is mentioned in the text.

KL 1500 HAL / KL 1500 H - Operating instructions
2/15
Contents
1. Important information ............................................................................... 4
2. Operation ................................................................................................. 6
2.1 Light guide connection ............................................................................. 6
2.2 Power connection …………………………………………………………... 6
2.3 Start up procedure .................................................................................. 7
2.4 Light intensity setting ................................................................................. 7
2.5 LCD display indication and settings …………………..……………….…. 8
2.6 Supplementary optics ……………………………………………………….…… 9
2.7 Filter slide .............................................................................................. 10
3. Lamp change ......................................................................................... 11
4. Maintenance .............................................................................................. 12
5. Troubleshooting ..................................................................................... 12
6. Accessories ............................................................................................... 13
7. Technical data ............................................................................................. 14

KL 1500 HAL / KL 1500 H - Operating instructions
3/15
The instrument at a glance
(1)On/offswitch 2.3
(2) Light guide socket with automatic shut off 2.1
(3) Locking screw 2.1
(4) Electronic light intensity setting 2.4
(5) LCD display 2.5
(6) Pivot lever for supplementary optics 2.6
(7)Filterslide 2.7
(8)Carryinghandle 1.
(9) Lamp compartment with halogen cold light reflector lamp 3.
(10) Mains connection socket 2.2
(11) Air vents (base of instrument) 1.
(12) Ventilation grid (back of instrument) 1.
(13) Model plate (base of instrument) 1.
5
2
8
7
12
4
1
6
3
9
11
13
10

KL 1500
H
1. Imp
o
Symbols
Sy
m
Intended
The KL 15
Cold light
s
of the lam
p
or self sup
According
The KL 1
5
directives:
2014/35/E
2014/30/E
2011/65/E
The tech
n
conformity
EN 61326
-
EN 61010
-
EN 50581
:
UL 61010
-
Saf
e
Please re
guarante
e
Never loo
(danger o
f
The KL 1
5
property o
light abso
r
please ad
h
H
AL / KL
1
o
rtant in
f
used:
m
bol Me
a
Wa
r
Wa
r
use:
00 HAL col
s
ources ar
e
p
's radiatio
n
porting, m
o
to the EN
6
5
00 HAL fi
U (Low Vol
t
U (EMC Di
r
U (RoHS)
n
ical docu
m
with the e
s
-
1:2013
-
1:2010
:
2012
-
1 Third Edi
e
ty infor
m
ad and o
b
e
d unless
y
k directly
f
ophthal
m
5
00 HAL e
m
f convertin
g
r
bing mater
h
ere to the
f
1
500 H -
O
f
ormatio
n
a
ning
r
ning of dan
g
r
ning of hot
s
d light sou
r
e
used for t
h
n
are filtere
d
o
vable light
6
2471:200
8
bre optic li
t
age Direct
i
r
ective)
m
entation
a
s
sential req
u
tion und C
A
m
ation:
b
serve th
e
y
ou obser
v
into the o
p
m
ic injury!)
m
its high i
n
g
incident
l
ials. To a
v
f
ollowing in
s
O
perating
n
g
er (caution,
s
urface
r
ce is inten
d
h
e intensiv
e
d
out. High
guides.
standard t
h
ght source
i
ve)
a
nd full co
u
irements
o
A
N/CS
A
-C
2
e
se instru
c
v
e the oper
a
p
en light
g
tensity visi
b
l
ight into h
e
v
oid such t
h
s
tructions:
instructi
o
obey docu
m
d
ed for indu
e
illuminati
o
intensity vi
s
h
e KL 150
0
conforms
mpliance
w
o
f the follo
w
2
2.2 No.611
c
tions car
e
ating instr
u
g
uide sock
b
le light. A
s
e
at, dama
g
h
ermal dam
o
ns
m
entation)
strial and l
a
o
n of all typ
e
s
ible light i
s
0
HAL is a
p
to the pro
v
w
ith the st
a
w
ing EC Dir
e
010-1-12
e
fully. Th
e
u
ctions.
et or the l
i
s
light abs
o
g
e may oc
c
age and th
e
a
boratory a
p
e
s of objec
t
s
guided to
t
p
roduct of
R
v
isions of
t
a
ndards li
s
e
ctives:
instrume
n
i
ght guide
o
rbing mat
e
c
ur to heat
e
potential
p
plications.
t
s. The infr
a
the object
u
R
isk Class 1
t
he followi
n
s
ted below
nts safety
exit durin
e
rials have
sensitive
o
danger of
f
4/15
a
red portio
n
u
sing flexibl
.
n
g Europe
a
proves th
cannot
b
g operatio
the physic
a
o
r flammabl
f
ire or burn
s
n
s
e
a
n
e
b
e
n
a
l
e
s
,

KL 1500
H
xNever
c
xNever
c
(dange
r
xWhen
i
special
Also to
xWhen
t
proced
u
flamma
taken t
h
dark/co
xTo avo
i
brightn
e
xEnsure
Please
m
Öyour
Öall
a
inte
g
Öthe l
a
of th
e
(
w
Öthe f
i
mar
k
Öthe f
i
"Filt
e
Öthe l
i
iThe lig
h
data").
iThe ins
t
iSafe di
s
iThe in
s
Repair
s
agenci
e
iPlease
iThe m
a
H
AL / KL
1
c
over up th
e
c
over up t
h
r
of burns!)
i
lluminating
care must
select a su
i
t
he light s
o
u
re must a
ble light ab
h
at each li
g
loured texti
id unnece
s
e
ss and du
r
a safe eart
m
ake sure
t
KL 1500 H
a
ir vents (1
g
rated ther
m
a
mp has c
o
e
lamp co
m
w
arning of
h
i
lter slide a
n
k
ed with a
w
i
lter slide is
e
r slide"!)
i
ght guide i
s
h
t source
h
t
rument m
u
s
connectio
n
s
trument m
a
s
must onl
y
e
s.
ensure tha
t
a
nufacturer
1
500 H -
O
e
light guid
e
h
e open of
heat sen
s
be taken t
o
i
table lamp
o
urce is s
w
lways be
a
sorbing m
a
g
ht guide
e
les and da
r
s
sary strain
r
ation of illu
hing conne
t
hat
AL cold lig
h
1, 12) are
m
o switch
w
o
oled off b
e
m
partment t
o
h
ot surface
)
n
d insert fil
t
w
arning sig
n
always loc
s
cooled of
f
h
as been d
e
u
st not be u
s
n
from the
p
a
y neither
y
be carrie
d
t
every use
r
is not liabl
e
O
perating
e
exit (dang
e
the light
g
s
itive or fl
a
o
keep an
a
brightness
w
itched on
,
a
safe dist
a
a
terials (pr
e
e
xit is at t
h
r
k/coloured
on biolog
i
mination to
c
tion when
h
t source is
kept clea
w
ill cut off th
e
e
fore being
o
remind y
o
)
t
er have co
o
n
ked in plac
e
f
before bei
n
e
veloped f
o
s
ed in expl
o
p
ower suppl
b
e opened
d
out by t
h
r
of the sys
t
e
for damag
e
instructi
o
er of fire!)
g
uide exit
w
a
mmable li
g
a
ppropriate
level in or
d
,
all light
g
a
nce – at
e
vention of
h
e above
m
wooden or
i
cal tissue
the absolu
connectin
g
operated
a
r
at all ti
m
e instrume
n
replaced.
A
o
u of this n
e
o
led off bef
o
e
during th
e
n
g replace
d
o
r operatio
n
o
sive area
s
l
y is only g
u
nor disma
h
e manufa
c
t
em has qu
i
e caused b
o
ns
w
ith your h
g
ht absor
b
distance b
d
er to avoid
g
uide exist
s
least 10 c
m
p
ossible fir
e
m
entioned
s
plastic sur
f
by illumin
a
te minimu
m
g
the device
a
t the volta
g
m
es. In the
n
t tempora
r
A
warning
s
e
cessity:
o
re the ins
e
e
operation
d
.
n
in dry ro
o
.
u
aranteed
b
ntled. Tec
h
c
turer or b
y
i
ck access
t
y
failure to
a
nds or ot
h
ing object
s
etween th
e
thermal da
s
not bein
g
m
– away
e
hazard).
C
s
afe distan
a
ces.
a
ting with
v
m
level requ
g
e stated o
n
event of
ily (see Poi
s
ign has be
e
e
rt filter is r
e
of the light
o
ms only! (
b
y pulling o
u
h
nical modi
f
y
its autho
r
t
o these op
e
o
bey these
her parts
o
s
(e.g. in
m
e
light guid
e
mage to th
e
g
used in
from heat
C
are must
n
ce away,
f
v
isible light
,
ired.
n
the model
insufficient
nt 5 "Trou
b
en attache
d
e
moved. T
h
source (se
e
(
see Point
7
u
t the main
s
fications a
r
rised cust
o
erating ins
t
instruction
s
5/15
o
f your bo
d
m
icroscop
y
e
and obje
c
e
object.
the workin
sensitive
o
therefore
b
f
or exampl
e
reduce th
plate (13);
cooling,
a
leshooting
"
d
in the do
o
h
e slide is
e
Point 2.6
7
"Technic
a
s
plug.
r
e forbidde
n
o
mer servi
c
ructions.
s
.
d
y
y
),
c
t.
g
o
r
b
e
e
:
e
a
n
"
)
o
r
a
l
n
.
c
e

KL 1500
H
2. Ope
r
2.1 Ligh
t
Start by l
o
Insert the l
A
ttention:
W
fits into on
e
Saf
e
ATTENTI
O
Light guid
e
down bef
o
replacing t
The light
g
prevents t
h
opening.
T
the light g
u
If the light
It will turn
b
affect the
b
A
s long a
s
the LCD d
i
2.2 Pow
e
Insert the
(optional
a
on the ba
c
connected
Please en
s
source onl
When repl
a
used.
H
AL / KL
1
r
ation
t
guide c
o
o
osening th
ight guide
a
W
hen inse
r
e
of the tw
o
e
ty infor
m
O
N!
e
s can bec
o
o
re replacin
g
he light gui
d
g
uide sock
e
h
e operati
o
T
his protec
t
u
ide is exc
h
guide is re
m
b
ack on as
b
rightness l
s
there is n
o
i
splay (5)
w
e
r connec
three pin
a
ccessory)
i
c
k of the i
n
to the mai
n
s
ure that y
o
y within th
e
a
cing the p
o
1
500 H -
O
o
nnection
e locking
s
a
s far as it
w
r
ting light g
o
guide slot
s
m
ation:
o
me hot du
g
it. It is re
d
e.
A
warni
e
t (2) is equ
o
n of the la
m
t
s the user
h
anged by
m
m
oved fro
m
soon as th
e
evel set at
t
o
light guid
e
w
ill show th
e
tion:
power co
r
i
nto the de
s
n
strument.
T
n
s supply (
1
o
u operate
y
e
specified
v
o
wer cord t
O
perating
s
crew (3) o
w
ill go and
t
u
ides with
a
s
.
ring prolon
g
commende
ng sign ha
s
ipped in a
d
m
p unless
from being
m
istake bef
o
m
the light g
e
light guid
e
t
he light int
e
e
in the lig
h
e
error me
s
r
d of type
s
ignated pl
T
he instru
m
1
00-240 V
A
y
our KL 15
0
v
oltage ran
g
he same ty
instructi
o
o
f the light
g
t
ighten the
a
locating
p
g
ed use. P
l
e
d to turn o
f
s
been atta
c
d
dition with
a recomm
e
g
blinded d
u
o
re the ligh
t
uide socke
t
e
is reinser
t
e
nsity setti
n
h
t guide so
c
s
sage "No
L
H05VV-F
3
ug in sock
e
m
ent needs
A
C, 50-60
H
0
0 HAL col
d
g
e.
y
pe must b
e
o
ns
g
uide sock
locking scr
e
p
in, care m
u
ease mak
e
f
f the light
s
c
hed to
a sensor s
y
e
nded light
u
ring opera
t
source is
t
t
(2) during
t
ed into the
n
g (4).
c
ket (2) wh
e
L
ight Guide
"
G0,75
e
t (10)
to be
H
z).
d
light
e
e
t (2) by t
u
e
w by turni
n
u
st be take
n
e
sure that
t
s
ource for
a
remind yo
u
y
stem (aut
o
guide is s
e
t
ion withou
t
t
urned off a
operation,
light guide
e
n the ligh
t
"
.
u
rning it a
n
n
g it clock
w
n to ensur
e
t
he light gu
i
a
bout 5 mi
n
u
of this ne
c
o
matic swit
c
e
ated in th
e
t light guid
e
a
t the on/off
the lamp
w
socket (2).
t
source is
s
6/15
n
ti-clockwis
e
w
ise.
e
that the pi
i
de is cool
e
n
utes befo
r
c
essity.
c
h off) whi
c
e
designat
e
e
, e.g. wh
e
switch (1).
w
ill switch o
f
This will n
o
s
witched o
n
e
.
n
e
d
r
e
c
h
e
d
e
n
f
f.
o
t
n
,

KL 1500 HAL / KL 1500 H - Operating instructions
7/15
2.3 Start up procedure
Switch on/off the KL 1500 HAL by pressing the on/off switch (1).
The indicator on the LCD display (5) is lit when the instrument is switched on.
Position O: The instrument is switched off. Please disconnect the power by pulling out the power
plug!
To protect the halogen lamp the KL 1500 HAL is fitted with a gentle start up device that reduces the
high switch on current that would otherwise occur.
2.4 Light intensity setting
The brightness can be adjusted continuously by turning the light intensity setting rotary
dial (4).
The set brightness is indicated on the LCD display (5) in 1% increments between 0 and 100%. You
can have the light intensity displayed as the equivalent colour temperature [Kelvin] at the light guide
exit by means of a single press on the brightness control (4). Please note that this indicator is not an
exact physical quantity and therefore, subject to a certain level of inaccuracy! It is merely intended
as an approximate value! Neither fluctuations caused by manufacturing tolerances of the lamp nor
any ageing processes are taken into account!
The greatest light intensity is reached when the rotary dial is turned all the way to the 100% position
(3400K). The average lifetime of the lamp is approximately 50 h (as specified by the manufacturer of
the lamp).
The brightness of the KL 1500 HAL can be regulated across 3 different segments and is indicated
accordingly on the LCD display (5). These ranges can be used as an indicator for the application
specific brightness and thus for the lifetime of the lamp:
ECO 0 - 49% > 1,500 h
STANDARD 50 - 79% approx. 150 h – approx. 1,500 h
BOOST 80 - 100% approx. 50 h – approx. 150 h

KL 1500 HAL / KL 1500 H - Operating instructions
8/15
When the brightness control is set to 0% there is no more light intensity, i.e. the lamp is off.
Attention: Please note that when the brightness control is set to 0%, the instrument is not switched
off. You switch off the KL 1500 HAL by pressing the on/off switch (1) (see Point 2.3 "Start up
procedure"). Please ensure safe power disconnection by pulling out the power plug!
If necessary, you can have the total operating time of the lamp (varying with the set intensity)
displayed on the LCD display (see Point 2.5 "LCD display indication and settings").
2.5 LCD display indication and settings
Brightness indicator
The brightness set at the light intensity setting rotary dial (4) can be displayed either in per cent or
Kelvin (see Point 2.4). You can toggle the display by briefly pressing the light intensity setting rotary
dial (4) once.
Indicator of lamp operating time
You can have the LCD display (5) indicate the accumulated total operating time of the used halogen
lamp. This time is added up in full hours [h] throughout the lifetime of the lamp depending on which
type of voltage is used with the lamp.
You can use the menu control to switch this indicator on or off. To access the menu control, press
and hold the light intensity setting rotary dial (4) > 5 seconds. The lamp will switch off as soon as the
light source is set to menu control.
Turning the light intensity setting rotary dial (4) clockwise and anti-clockwise will move the indicator
arrow to the corresponding menu fields. The currently selected menu field is displayed as an
inverted field. Press the light intensity setting rotary dial (4) briefly once to open the selected
submenu.

KL 1500 HAL / KL 1500 H - Operating instructions
9/15
Select the submenu "On/Off" to enable the operating hour counter. Turn the light intensity setting
rotary dial (4) to select "On" and confirm your selection with a brief press of the rotary dial (a
checkmark will appear in the menu field). Select "Menu" followed by "Exit". The lamp will switch
back on. The operating hours are indicated at the top left of the LCD display (5).
To turn off the operating hour indicator, select "On/Off" in the submenu. Turn the light intensity
setting rotary dial (4) to select "Off" and confirm your selection with a brief press of the rotary dial (a
checkmark will appear in the menu field). Select "Menu" followed by "Exit".
If using the operating hour indicator of the lamp, you should reset the operating hour counter to 0 h
after changing the lamp. This will not happen automatically! Press and hold the light intensity setting
rotary dial (4) > 5 seconds to access the menu control. Next, select the "Reset" submenu. Turn the
light intensity setting rotary dial (4) to select "Reset" and confirm your selection with a brief press of
the rotary dial (a checkmark will appear in the menu field). Select "Menu" followed by "Exit". The
counting of the lamp's operating hours in the memory will start anew (beginning with 0h) regardless
of whether the operating hour indicator is turned or turned off.
2.6 Supplementary optics
The use of the supplementary optics ensures that you will achieve uniform, high intensity
illumination even when using light guides with a smaller bundle diameter than 9 mm.
If the illumination is carried out with imaging or focussing optical systems at the light guide exit,
perfectly uniform illumination is achieved by moving the supplementary optics out of the optical path.
To pivot the supplementary optics in and out, turn the pivot lever (6) clockwise or anti-clockwise to
the corresponding symbols. The supplementary optics always need to be pivot in or out as far as
they will go!

KL 1500
H
2.7 Filter
The KL 1
accessory
)
When ope
or in the r
e
Saf
e
ATTENTI
O
Operating
slide.
Fitting t
h
Saf
e
ATTENTI
O
Please en
s
been atta
c
Completel
y
filter with
2
with slight
To remov
e
If you wis
h
the first re
light path.
H
AL / KL
1
slide
500 HAL
h
)
.
rating the li
e
st position.
e
ty infor
m
O
N!
the light s
o
h
e filter
s
e
ty infor
m
O
N!
s
ure the fil
t
c
hed to
r
y
pull out t
h
2
8 mm dia
m
pressure (
c
e
easily ben
h
to operat
e
st position.
1
500 H -
O
h
as a filte
r
ght source
,
m
ation:
o
urce with
t
s
lide
m
ation:
t
er slide (7)
r
emind you
h
e filter slid
e
m
eter using
c
enter). Th
e
d the brac
k
e
the light
s
When in t
h
O
perating
r
slide (7)
,
the filter s
l
t
he filter sli
d
has coole
d
of this nec
e
e
(7) from t
h
lint-free gl
o
e
filter is th
e
k
et (left) to t
s
ource for
a
h
is position
instructi
o
which can
lide must a
d
e in an in
t
d
down bef
e
ssity.
h
e light so
u
o
ves from t
o
e
n lying flat
t
he left and
a
short tim
e
, the filter i
o
ns
be fitted
w
lways be e
n
t
ermediate
o
re fitting t
h
u
rce so that
o
p right be
h
inside the
h
remove th
e
e
without a
f
s
still in th
e
w
ith an in
s
n
gaged in
o
p
osition ca
n
h
e insert fil
t
the label i
s
h
ind the tw
o
h
older (righ
t
e
filter with
g
f
ilte
r
then
o
e
light sour
c
1
s
ert filter (
o
ne of the
e
n cause d
a
t
er.
A
warn
s
legible (le
f
o
retaining l
u
t
).
g
loves.
o
nly pull th
e
c
e, but no
l
1
0/15
a
vailable
a
e
nd positio
n
a
mage to th
ing sign h
a
f
t). Insert t
h
u
gs and fix
e
slide out
t
l
onger in th
a
s
n
s
e
a
s
h
e
it
t
o
e

KL 1500
H
3. Lamp
c
Saf
e
ATTENTI
O
Please en
warning si
g
Please en
s
Please be
Open the
l
the comp
a
Carefully
p
to the spe
into place
Insert the
p
Replacing
The high
q
operating
h
When repl
a
lamp as d
e
fastening
s
componen
(spare par
t
the clip an
d
firmly). Sli
p
described
H
AL / KL
1
c
hange
e
ty infor
m
O
N!
sure that
t
g
n has bee
s
ure that th
e
careful not
l
amp comp
a
a
rtment out
p
ull the def
e
cifications
g
inside the
p
ower plug
the lamp s
o
q
uality lamp
h
ours or 20
a
cing the l
a
e
scribed ab
s
crews at t
h
t completel
t
, see Poin
t
d
retighten
p
the lamp
b
above.
1
500 H -
O
m
ation:
t
he lamp a
n attached
e
light sour
c
to grasp in
t
a
rtment (9)
as far as i
t
e
ctive lamp
g
iven unde
holder. Sli
d
and switch
o
cket:
socket is
g
lamp repl
a
a
mp socket
,
ove. Use a
h
e top of th
e
y. Thread t
h
t
6.4) into t
h
the screws
b
ack on an
d
O
perating
nd lamp s
o
to remi
n
c
e is switc
h
t
o the devi
c
by pressin
t
will go. M
o
off the soc
k
r Point 6.4
)
d
e the lam
p
on the ligh
t
g
uaranteed
cements.
,
start by c
a
screwdrive
e
clip and r
e
h
e two cabl
h
e correspo
(making s
u
d
press it in
instructi
o
o
cket have
n
d you of t
h
h
ed off and
c
e. There is
g down an
d
ove the la
m
k
et and sli
p
)
. Proceed
p
compart
m
t
source.
to last for
2
a
refully pulli
e
r to loosen
e
move the
l
e ends of t
h
nding ope
n
u
re they ar
e
n
to the hold
e
o
ns
cooled d
o
h
is necessit
y
the power
p
a
r
isk of in
j
d
pulling at
m
p includin
g
p
on a new l
by pressin
g
m
ent back i
n
2
0,000
ng off the
both
h
e socket
n
ings on
e
seated
e
r as
o
wn before
y
.
p
lug is pull
e
j
ury by the
t
the design
a
g
socket u
p
amp (use
a
g
down on
n
until it lo
c
1
replacing
e
d out.
trailing fan.
ated reces
s
p
and out
o
a
lamp that
the lamp
u
c
ks (audibl
y
1
1/15
the lamp.
A
s
and pullin
o
f the holde
correspon
d
u
ntil it sna
p
y
) into plac
e
A
g
r.
d
s
p
s
e
.

KL 1500 HAL / KL 1500 H - Operating instructions
12/15
4. Maintenance
Your KL 1500 HAL is maintenance free.
Disinfecting the light source during medical applications is to be avoided.
To clean the outside of the instrument, use a soft dry cloth or commercially available plastic cleaning
cloths.
5. Troubleshooting
Should you be unable to correct the fault you are experiencing applying the measures listed below,
turn to your authorised dealer or the next SCHOTT dealership. More extensive repairs have to be
performed by authorised service technicians.
Errors and faults are commonly displayed on the LCD display (5) (see Point 2.5):
Overheating: Insufficient cooling; temperature monitor has triggered
Open Circuit: Lamp circuit interrupted; lamp defective or missing
No Fan: Fan defective
No Light Guide: no light guide in the light guide socket (2)
Type of the fault Possible cause Remedy
Lamp off, fan not running, no
LCD display
Instrument not switched on
Switch the instrument on
Plug not in socket Insert the plug
No mains voltage Check mains voltage
Lamp off, fan running, fault
status indication "Open
Circuit"
Lamp compartment not
connected
Lamp defective
Connect lamp compartment
Replace lamp (see Point 3 of
these instructions)
No lamp
No lamp contact
Insert lamp with light source
switched off
Press lamp into the socket

KL 1500 HAL / KL 1500 H - Operating instructions
13/15
Lamp off, fan running, fault
status indication
"Overheating"
Electronics overheated Provide for sufficient cooling,
verify correct lamp type, place
the instrument back into
operation after an extended
cooling period
Lamp off, fan not running,
fault status indication "No
Fan"
Fan defective, impeller jammed Have authorised customer
service perform repairs
Lamp off, fan running, fault
status indication "No Light
Guide"
No recommended light guide in
the light guide socket
Light guide is not plugged in
until it stops
Plug recommended light guide
into the light guide socket, check
for proper seating
Plug in light guide into the light
guide socket until it stops
6. Accessories for KL 1500 HAL
A wide range of accessories is available for your KL 1500 HAL. A separate brochure gives you
comprehensive information (turn to page 15 for the order address)
Only SCHOTT light guides and accessories guarantee perfect operation, safety and optimum light
yield.
6.1 Light guides
Self supporting and flexible light guides in various lengths and diameters are available, as well as
point and slit illuminators.
6.2 Halogen lamps
When ordering halogen lamps as spare parts (see point 6.4 of these instructions), you will receive
the lamp type that gives you the maximum light yield and best possible degree of illumination.
6.3 Filters
Optical filters can either be inserted into the filter slide (7) or placed in front of the light guide exit as
a screw in or push on filter in conjunction with an auxiliary focussing device (accessory).
Details of the auxiliary focussing device and the filter types available as standard can be found in
the accessories catalogue.

KL 1500 HAL / KL 1500 H - Operating instructions
14/15
6.4 Spare parts
Halogen lamp 15 V / 150 W (catalogue no. 153000)
Philips, type 6423
Philips, type 6423 XHP
Osram, type HLX 64634
Lamp socket (catalogue no. 150710)
Only the use of the spare parts listed above will ensure maximum performance, light yield and
safety.
7. Technical data KL 1500 HAL
Properties Values
General information
Type description - KL 1500 HAL
Dimensions (W x D x H) mm approx. 202 x 146 x 286
Weight kg approx. 4,2
Cooling - Axial fan
Ambient temperature °C + 5 ... + 40
Relative humidity % at 31°C ambient temperature:
85%
31°C to 40°C ambient temperature:
linearly decreasing to 75%
Air pressure hPa 800 ... 1060
Transport and storage
Temperature °C
Rel. humidity %
Air pressure hPa
-20 ... +70
10 ... 95 (non-condensing)
500 ... 1200
Electrical information
Operating voltage, frequency 100 - 240 V ~
50 - 60 Hz
Power consumption, max. VA max. 180
Protection class - I
Overvoltage category II
Lamp type - Halogen reflector lamp
Philips, type 6423
Philips, type 6423 XHP
Osram, type HLX 64634
Lamp rated voltage V 15
Lamp rated power W 150
Average lamp lifetime
Level 50% h
Level 80% h
Level 100% h
1500
150
50

KL 1500
H
Lighting i
n
Maximum
e
Total light
f
(SCHOTT
Level 50%
Level 80%
Level 100
%
Light entry
Heat prote
c
Markings
Approvals
EMC emis
s
The right i
s
technical
d
Manufac
t
SCHOTT
Lighting
a
Otto-Sch
o
55127 M
a
Germany
Tel. +49 (
H
AL / KL
1
n
formation
e
ffective lig
h
f
lux at light
g
light guide
Ø
%
angle (2
D e
f
c
tion filter
s
ion class
s
reserved
t
d
evelopme
n
t
urer’s A
d
AG
a
nd Imagin
o
tt-Strass
e
a
inz
0) 6131 /
6
WEEE
High-q
the de
v
This s
y
be dis
p
have r
e
SCHO
T
syste
m
Pleas
e
us in h
For m
o
www.s
1
500 H -
O
h
t guide bun
d
g
uide exit
Ø
9 mm, typ.
f
f)
t
o make ch
a
n
t.
d
ress:
g Division
e
2
6
6 - 0
Declaration
uality materials
v
elopment and
t
y
mbol means th
p
osed of separ
a
e
ached their en
T
T AG Lighting
m
that customer
s
e
make use of t
h
elping preserv
e
o
re information
o
chott.com/lighti
n
O
perating
d
le diameter
m
m
values)
l
m
lm
lm
-
-
-
-
a
nges in th
e
and componen
t
he production
o
at electrical an
d
a
tely from your
h
d
-of-life.
and Imaging h
a
s
can use to dis
h
is system to di
s
e
the environme
o
n our return s
y
n
gimaging/recy
c
instructi
o
m
9
m
m
m
approx
.
approx
.
approx
.
approx
.
SCHO
T
d = 2.0
B
e
design a
n
n
ts have been u
s
o
f your SCHOT
T
d
electronic eq
u
h
ousehold wast
a
ve arranged f
o
s
pose of their e
q
s
pose of your p
nt in which we l
y
stem, log on to
cle
.
o
ns
.
250
.
450
.
600
.
85°
T
T KG 2, 45
mm, tough
e
n
d supplied
s
ed during
T
product.
u
ipment must
e after they
o
r a return
q
uipment.
r
oduct. Join
ive.
x 45
ned
items withi
n
1
n the scop
e
1
5/15
e
of on-going

DistributionintheUK&Ireland
LambdaPhotometricsLimited
LambdaHouseBatfordMill
HarpendenHertsAL55BZ
UnitedKingdom
E:[email protected]
W:www.lambdaphoto.co.uk
T:[phone]
F:[phone]
Distribution in the UK & Ireland
Lambda Photometrics Limited
Lambda House Batford Mill
Harpenden Herts AL5 5BZ
United Kingdom
E: [email protected]
W: www.lambdaphoto.co.uk
T: [phone]
F: [phone]