Prestel HD-PTZ430HSU3 User manual

USER MANUAL
Prestel HD-PTZ430HSU3
1080P HD PTZ Camera

Copyright
All contents of this manual, whose copyright belongs to ourcorporation, cannot be
cloned, copied or translated without the permission of our corporation.
Notice
Product specifications and information which were referred to in this document are for
reference only. We may change, delete, or update any content at any time and without
prior notice.
FCC NOTICE (Class A)
This product complies with Part 15 of the FCC Rules. The operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
This product has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonableprotection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with theinstructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does causeharmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
Class A ITE
Class A ITE is a category of all other ITE which satisfies the class A ITE limits but not the
class B ITE limits. Such equipment should not be restricted in its sale but the following
warning shall be included in the instructions for use:
Operating this equipment in a residential environment may cause radio interference.
European Community Compliance Statement (Class A)
This product is herewith confirmed to comply with the requirements set
out in the Council Directives on the Approximation of the laws of the
Member States relating to Electromagnetic Compatibility Directive
Note
Warning

1080P HD PTZ Camera User Manual
Catalogue
1Safety Precautions........................................................................................ 1
2Packing List................................................................................................... 1
3Quick Start .................................................................................................... 1
4Video Format.................................................................................................3
5About Product...............................................................................................3
5.1 Features................................................................................................................3
5.2 Specifications .......................................................................................................3
5.3 Interface and Switch .............................................................................................5
5.4 Dimension .............................................................................................................5
5.5 Installation ............................................................................................................ 7
5.6 Remote Control .....................................................................................................9
6GUI Settings ................................................................................................10
6.1 Menu ................................................................................................................... 10
6.2 Exposure ............................................................................................................. 10
6.3 Color ....................................................................................................................11
6.4 Image .................................................................................................................. 12
6.5 Display ................................................................................................................ 12
6.6 P/T/Z Setting....................................................................................................... 12
6.7 Setting ................................................................................................................ 13
6.8 Version ............................................................................................................... 13
6.9 Default ................................................................................................................ 14
7WEB Settings ..............................................................................................14
7.1 Access Camera ................................................................................................... 14
7.2 Control Camera ................................................................................................... 14
7.3 Video Settings..................................................................................................... 16
7.4 Image Settings .................................................................................................... 17
7.5 Audio Settings..................................................................................................... 17
7.6 System Settings .................................................................................................. 18
7.7 Network Settings................................................................................................. 18
7.8 Device Information ..............................................................................................20
7.9 Download Upgrade Program................................................................................20
8Troubleshooting .........................................................................................20

1080P HD PTZ Camera User Manual
1
1Safety Precautions
During the installation and use of the
equipment, all electrical safety
regulations of the country and region
of use must be strictly observed.
Please use the power adapter that
comes standard with this product.
Please do not connect multiple
devices to the same power adapter
(exceeding the capacity of the
adapter may generate excessive heat
or cause a fire).
Do not rotate head of the camera by
hand, otherwise it may cause
mechanical failure.
When installing this product on a wall
or ceiling, secure the device securely.
When installing, make sure that there
are no obstacles within the rotation
range of the gimbal; do not turn on the
power until all installations are
completed.
To avoid heat build-up, keep
ventilation around the device smooth.
If the device emits smoke, smells, or
makes noises, please turn off the
power immediately and unplug the
power cord, and contact the dealer in
time.
This device is not waterproof, please
keep the device dry.
This product has no user serviceable
parts, damage caused by disassembly
by the user is not covered by the
warranty.
Specific frequencies of electromagnetic
field
may affect the image of the camera!
2Packing List
Name
Quantity
Camera
1
Power Adapter
1
Power Cable
1
RS232 Cable
1
USB Cable (Optional)
1
Remote Control
1
User Manual
1
3Quick Start
1) Please check connections are correct before starting.
Notice

1080P HD PTZ Camera User Manual
LINEIN LINE OUT
SYSTEM
SELECT RS485
IN RS232 OUT
LAN HDMI 3G-SDI USB 3. 0 DC 12V OFF
ON
Computer, TV,VCR wi th
audio input jack,
Routers or Switches,
Speaker Microphone,etc.
RS232 Cable (Supplied)
RS232 Cable (Not Supplied)
RS485 Cable (Not Supplied)
3.5mm Audio Cable(Not Supplied)
3.5mm AudioCable(Not Supplied)
HDMICable(Not Supplied)
DC12VIN Power Cable (Supplied)
AC Ad apter (Supplied)
Network Cable(Not Supplied)
3G-SDI Cable (Not Supplied)
USBCable (Optional)

1080P HD PTZ Camera User Manual
3
2) Connect the power adapter to the
power connector on the rear panel of
the camera. The power indicator on
the front panel of the camera is on.
3) After the camera is powered on, it
starts to initialize, right up to the limit
position, and then both horizontal
and vertical go to the middle position,
the motor stops running, and the
initialization is completed.
(Note: If preset 0 is saved, PTZ will be
move to preset 0)
4Video Format
Video Format
0
1080P60
8
-
1
1080P50
9
-
2
-
A
-
3
-
B
-
4
720P60
C
-
5
720P50
D
-
6
1080P30
E
-
7
1080P25
F
-
5About Product
5.1 Features
60.7° Wide-angle Lens + 30x Optical
Zoom
60.7° high-quality ultra-wide-angle lens,
optical zoom up to 30x, support 8x
digital zoom.
1080P Full HD
Using 1/2.8-inch high-quality HD CMOS
sensor with effective 2.07 million pixels,
it can achieve high-quality images with a
maximum resolution of 1920x1080.
New ISP Image Processing Algorithm
The new generation of ISP image
processing algorithm provides more
complete white balance and automatic
exposure functions, which significantly
improves the image output performance
of the camera, and the imaging effect is
also better. Widely used in education
recording and broadcasting, distance
education, video conferencing, live
broadcasting, broadcasting and other
industries.
Leading Auto Focus Technology
Using advanced focusing algorithm, the
lens can focus quickly, accurately and
stably.
Low Light
The application of 2D and 3D noise
reduction algorithm greatly reduces
image noise. Even under the condition of
ultra-low illumination, it still keep the
picture clean and clear, and the SNR of
image is as high as 55dB.
Multiple Interfaces
Support HDMI and 3G-SDI interface,
effective transmission distance of
3G-SDI is up to 150 meters (1080P30).
HDMI, 3G-SDI, LAN can output three HD
digital signals at the same time.
Remote Control
Through the RS232 and RS485 serial
ports, the camera can be controlled
remotely.
5.2 Specifications
Camera
Signal System
1080P60, 1080P50,
1080P30, 1080P25,
720P60, 720P50
Sensor
1/2.8 inch, CMOS,
Effective pixels: 2.07M
Scanning
Mode
Progressive
Lens
30x,
f=4.42mm~132.6mm,
F1.8~F2.8
Digital Zoom 8x
Minimum
Illumination
0.5 Lux @ (F1.8, AGC
ON)

1080P HD PTZ Camera User Manual
4
Shutter 1/30s ~ 1/10000s
White Balance
Auto, VAR, Manual,
One Push, Indoor,
Outdoor
Backlight
Compensatio
n
Support
Digital Noise
Reduction
2D & 3D Digital Noise
Reduction
SNR ≥55dB
Horizontal
FOV
60.7° ~ 2.28°
Vertical FOV 34.1° ~ 1.28°
Pan Angle ±170°
Tilt Angle -30° ~ +90°
Pan Speed 1.7° ~ 100°/s
Tilt Speed 1.7° ~ 69.9°/s
Image Flip Support
Image Freeze Support
Preset
Position
255
Preset
Accuracy
0.1°
Audio Features
Microphone
Array
Built-in dual
microphones, 100Hz to
16KHz frequency
response
Audio Input
Support LINE IN audio
input
Audio Output
Support LINE OUT,
HDMI, USB and other
audio output
USB Features
Operate
System
Windows 7/8/10, Mac
OS X, Linux, Android
Color System
/
Compression
YUY2/MJPEG/H.264
USB Audio Support
USB Video
Protocol
UVC 1.1/UVC 1.5
UVC PTZ
Control
Support
Network Features
Video
Compression
H.264/H.265
Video Stream
First Stream,
Second Stream
First Stream
Resolution
1920x1080, 1280x720,
1024x576, 960x540,
640x480, 640x360
Second
Stream
Resolution
1280x720, 1024x576,
720x480, 640x360,
480x272, 320x240,
320x180
Video Bit Rate 32Kbps~20480Kbps
Bit Rate
Control
CBR, VBR
Frame Rate 1fps ~ 60fps
Audio
Compression
AAC
Audio Bit Rate
96Kbps, 128Kbps,
256Kbps
Protocols
TCP/IP, HTTP, RTSP,
ONVIF,RTMP/RTMPS,
DHCP, SRT, Multicast,
etc.
Interfaces
LINE IN
Interface
1 x LINE IN: 3.5mm
Audio
Interface
LINE OUT
Interface
1 x LINE OUT: 3.5mm
Audio
Interface
Communicati
on Interface
1 x RS485: 2pin phoenix
port, Max Distance:
1200m, Protocol:
VISCA/
Pelco-D/Pelco-P
1xRS232 IN: 8pin Min
DIN, Max Distance:
30m, Protocol:
VISCA/Pelco-D/
Pelco-P
1 x RS232 OUT: 8pin
Min DIN, Max Distance:
30m, Protocol: VISCA
network use only
Network
Interface
1xLAN: 10M/100M
Adaptive Ethernet Port

1080P HD PTZ Camera User Manual
5
HDMIInterface 1 x HDMI: Version 1.3
3G-SDIInterfa
ce
1x3G-SDI: BNC type,
800mVp-p, 75
Ω
. Along
to SMPTE 424M
standard
USBInterface 1xUSB 3.0: Type A
Power Jack JEITA type (DC IN 12V)
General Specifications
Input Voltage DC 12V
Input Current Max. 1.2A
Operating
Temperature
0°C ~ 40°C
Storage
Temperature
-40°C ~ 60°C
Power
Consumption
Max. 15W
Dimension
169mm x 141.5mm x
176mm
Net Weight About 1.5Kg
Product specifications and
parameters are subject to
change without notice.
5.3 Interface and Switch
Item
Description
1
LINE IN Interface
2
LINE OUT Interface
3
System Select Switch
4
RS485 Interface
5
RS232 IN Interface
6
RS232 OUT Interface
7
LAN Interface
8
HDMI Interface
9
3G-SDI Interface
10
USB3.0 Interface
11
DC 12V Interface
12
Power Switch
5.4 Dimension
Note
LINEIN LINE OUT
SYSTEM
SELECT RS485
IN RS232 OUT
LAN HDMI 3G-SDI USB 3. 0 DC12V OFF
ON
1
9
2 3 4 5 6
7 8 10 11 12
STANDBY POWER
176
140
Ø141.5

1080P HD PTZ Camera User Manual
6
151
169
141.5

1080P HD PTZ Camera User Manual
7
5.5 Installation
The installation diagram is for reference only. The brackets and screws are
not standard.
Wall-Mount
1
2
3
4
Ceiling-Mount
1
2
3
4
Note

1080P HD PTZ Camera User Manual
8
For packing accessories, please refer to the actual product.

1080P HD PTZ Camera User Manual
9
5.6 Remote Control
Key Description
1. Standby Key
Press to enter standby mode
2. Number Key
Press to set preset or call preset
3. *Key
Use with other keys
4. PRESET Key
Set preset: [PRESET] + Number key (0-9)
5. HOME Key
Confirm selection or press to turn PTZ
back to the middle position
6. Return Key
Press to return to the previous menu
7. ZOOM Key
SLOW: Zoom In [+] or Zoom Out [-]
slowly
FAST: Zoom In [+] or Zoom Out [-]
fast
8. L/R SET Key
Standard: Simultaneously press L/R
SET + 1
Reverse: Simultaneously press L/R
SET + 2
9. FOCUS Key
Auto/Manual/Far/Near focus
10.CAMERA SELECT Key
Press to select and control the camera
11. #Key
Use with other keys
12. IR Remote Control Key
[*]+[＃]+[F1]: Address 1
[*]+[＃]+[F2]: Address 2
[*]+[＃]+[F3]: Address 3
[*]+[＃]+[F4]: Address 4
13. RESET Key
Clear preset position: [RESET] + Number
key (0-9)
14. PTZ Control Key
PTZ moved according to the arrow
indicates
15. MENU Key
Press toenter or exit OSD Menu
16. BACKLIGHT Key
Backlight ON/OFF: Press repeatedly to
enable or disable the backlight
compensation.
NOTE:
Effective only in auto exposure
mode.
If there is a light behind the subject,
the subject will become dark, press
the backlight key to enable the
backlight compensation. Press again
to disable this function.
17. P/T RST (PTZ Reset) Key
PTZ starts to self-test after pressed it
Shortcut Set
[*]+[＃]+[1]: OSD menu default English
[*]+[＃]+[3]: OSD menu default Chinese
[*]+[＃]+[4]: Display currentIP address
[*]+[＃]+[6]: Quickly recover the default
[*]+[＃]+[8]: View the camera version
0
987
654
3
21
#
1 2 43
F2 F3 F4
PRESET
CAMERA SELECT
STD REV
RESET
MENU
SLOW
BACKLIGHT
FOCUS
ZOOM FAST
F1
/ /
1
9
2
3
4
5
6
7
8
10
11
12
13
14
15
16
17

1080P HD PTZ Camera User Manual
10
[*]+[＃]+[9]: Quickly set up inversion
[*]+[＃]+[MANUAL]: Restore default IP
address
6GUI Settings
6.1 Menu
Press [MENU] key to display the main
menu on the normal screen, using arrow
key to move the cursor to the item to be
set. Press the [HOME] key to enter the
corresponding sub-menu.
Menu
ENG/中文
ENG
Video Format
1080P60
Style
Default
Exposure
->
Color
->
Image
->
Display
->
PTZSetting
->
Setting
->
Version
->
Default
->
[MENU]Return /[HOME]Enter
ENG/中文: ENG, 中文.
Video Format: 1080P60, 1080P50,
1080P30, 1080P25, 720P60, 720P50.
Style: Default, Cold, Warm, Clear, Soft,
User1, User2, User3.
6.2 Exposure
Move the main menu cursor to
[Exposure],
and press [HOME] key enter the
exposure
page, as shown in the following figure.
Exposure
>
AE
Auto
Flicker
50Hz
Expcomp
Mode
On
Expmode
2
Backlight
Off
Gain Limit
15
DRC Mode
Off
[MENU]Return /[HOME]Enter

1080P HD PTZ Camera User Manual
11
AE: Auto, Manual, Iris Priority, Shutter
Priority, Bright Priority.
Flicker: Off, 50Hz, 60Hz (Effective only
in Auto, Iris Priority, Bright Priority
mode).
Expcomp Mode: On, Off (Effective only in
Auto, Iris Priority mode).
Expmode: -7~7 (Effective only in
Expcomp Mode to On).
Backlight: On, Off (Effective only in Auto,
Iris Priority mode).
Bright: 0~99 (Effective only in Bright
Priority mode).
Gain Limit:0~32 (Effective only in Auto,
Iris Priority, Bright Priority mode).
Iris: F1.8, F2.0, F2.4, F2.8, F3.4, F4.0,
F4.8, F5.6, F6.8, F8.0, F9.6, F11, Off
(Effective only in Manual, Iris Priority
mode).
Shutter:1/30, 1/50, 1/60, 1/90, 1/100,
1/125, 1/180, 1/250, 1/350, 1/500, 1/725,
1/1000, 1/1500, 1/2000, 1/3000, 1/4000,
1/6000, 1/10000 (Effective only in
Manual, Shutter Priority mode).
Gain:0~31 (Effective only in Manual,
Shutter Priority mode).
DRC Mode: Manual, Auto, Off.
DRC: 0~14 (Effective only in DRC Mode to
Manual).
6.3 Color
Move the main menu cursor to [Color],
and press [HOME] key enter the color
page, as shown in the following figure.
Color
>
AWB
Auto
Sens
Low
R-Tuning
0
B-Tuning
0
Hue
50
Saturation
100
[MENU]Return /[HOME]Enter
AWB:Auto, VAR, Manual, One Push,
Indoor, Outdoor.

1080P HD PTZ Camera User Manual
12
Sens: Low, Middle, High.
R-Gain: 0~1023 (Effective only in Manual,
One Push mode).
B-Gain: 0~1023 (Effective only in Manual,
One Push mode).
R-Tuning:-128~128 (Effective only in
Auto, Temp, One Push mode).
B-Tuning:-128~128 (Effective only in
Auto, Temp, One Push mode).
Hue: 0~99.
Saturation: 0~200.
Temp: 2000 ~ 8500 (Effective only in
Temp mode).
6.4 Image
Move the main menu cursor to [Image],
and press [HOME] key enter the image
page, as shown in the following figure.
Image
>
Brightness
50
Contrast
50
Sharpness
Mode
Auto
Gamma Mode
Manual
Gamma
Ext
NR-2D Mode
Auto
NR-3D Mode
Auto
[MENU]Return /[HOME]Enter
Brightness: 0~99.
Contrast: 0~99.
Sharpness Mode: Manual, Auto.
Sharpness: 0~25 (Effective only in
Sharpness Mode to Manual).
Gamma Mode: Manual, Auto.
Gamma: Ext, 0.45, 0.5, 0.54, 0.56, 0.63
(Effective only in Gamma Mode to
Manual).
NR-2D Mode: Manual, Auto.
NR-2D: 0~99(Effective only in NR-2D
Mode to Manual).
NR-3D Mode: Manual, Auto.
NR-3D: 0~15 (Effective only in NR-3D
Mode to Manual).
6.5 Display
Move the main menu cursor to [Display],
and press [HOME] key enter the display
page, as shown in the following figure.
Display
>
OSD-Dir
0
HDMIMode
HDMI
SDIMode
Level A
Flip-H
Off
Flip-V
Off
Freeze
Off
[MENU]Return /[HOME]Enter
OSD-Dir: 0, 90, 180, 270.
HDMI Mode: HDMI, DVI.
SDI Mode: Level A, Level B.
Flip-H: On, Off.
Flip-V: On, Off.
Freeze: On, Off.
6.6 P/T/ZSetting
Move the main menu cursor to [P/T/Z
Setting], and press [HOME] key enter the
P/T/Z setting page, as shown in the
following figure.
P/T/Z Setting
>
AF-Sense
High
AF-Zone
Front
Focus Limit
Off
LR Mode
STD
Motion Sync
Off
Horizontal
Speed
23
Vertical Speed
19
Zoom Speed
7
PTbyZoom
On
[MENU]Return /[HOME]Enter
AF-Sense: High, Normal, Low.
AF-Zone: Front, Top, Center, Bottom.
Focus Limit: On, Off.
Near Focus Limit: 1M, 1.5M, 2M, 3M, 4M,
5M, 6M, 8M, 10M, 15M, 20M (Effective
only in Focus Limit to On).
Far Focus Limit: 15M, 20M, Infinity

1080P HD PTZ Camera User Manual
13
(Effective only in Focus Limit to On).
LR Mode: STD, REV.
Motion Sync: On, Off.
Horizontal Speed:0~23.
Vertical Speed:0~19.
Zoom Speed: 0~7.
PTbyZoom: On, Off.
6.7 Setting
Move the main menu cursor to [Setting],
and press [HOME] key enter the setting
page,
as shown in the following figure.
Setting
>
ViscaAddr
1
ViscaMode
Series
Baud Rate
9600
DHCP
Off
IP Addr
192.168.100.88
MAC
d4e08e548d13
[MENU]Return /[HOME]Enter
Visca Addr: 1~7 (Effective only in VISCA
protocol).
Visca Mode: Serial, Paral.
Baud Rate: 2400, 4800, 9600, 19200,
38400,
57600, 115200.
DHCP: On, Off.
IP Addr: 192.168.100.88.
MAC: d4e08e548d13.
6.8 Version
Move the main menu cursor to [Version],
and press [HOME] key enter the version
page, as shown in the following figure.
Version
Main
X8.02.15
AF
14.04.04
Date
2022-08-18
Code
VF1
[MENU]Return
/[HOME]Enter
Main:Display the version number of the
main program of the camera.
AF:Display the camera autofocus version
number.
Date:Display the burning date of the main
program version of the camera.

1080P HD PTZ Camera User Manual
14
Code:Display the camera code. 6.9 Default
Move the main menu cursor to [Default],
press [HOME] key enter default page, as
shown in the following figure.
Default
>
Reset
No
[MENU]Return
/[HOME]Enter
Reset: Yes, No.
GUI menu and parameters are
subject to change without
notice.
7WEB Settings
7.1 Access Camera
Access http://192.168.100.88 to pop up
the login window, then input username
(default: admin) and password (default:
admin). After login, it will show as below:
7.2 Control Camera
All pages include two menu bars:
Real time monitoring: displaying video
imageParameter setup: with function
buttons.
A. Video Viewing Window
Video viewing window must be same as
video resolution, the bigger the
resolution is,the bigger the playing area
is.Double click viewing window,will
show full-screen,double click again,will
return to initialized size.
Note
Video
Image
Audio
System
Network
ZoomIn ZoomOut
Focus In FocusOut
23
19
Pan Speed
Tilt Speed
Live
Information

1080P HD PTZ Camera User Manual
15
Status bar in viewing window shown as
below:
1)Video playback pause button: control
real-time video pause, stop the last
picture, click recoverable video
again.
2) Audio control buttons: can adjust the
volume or set silent mode.
3) Full screen switch button.
B. PTZ Setup
1)Pan and Tilt Control
Up,Down,Left andRight arrows and the
home button allow you to manually drive
the camera to the desired position.
2) Zoom
Zoom Inand Zoom Out buttons allow for
wide or narrow view of the space.
3) Focus
FocusIn and Focus Out buttons allow for
fine manual focus adjustment if the
camera has any problems autofocusing
on thedifficult object.
4:48
Zoom In Zoom Out
FocusIn FocusOut
23
19
Pan Speed
Tilt Speed
7
Zoom Speed
7
FocusSpeed
Set Call
Preset
PTZ Back

1080P HD PTZ Camera User Manual
16
4) PTZ Speeds
Pan speed can be set at any rate between
1 ~ 24, Tilt speed can be set at any rate
between 1 ~ 20. Zoom and Focus speeds
can be set at any rate between 1 ~ 7.
5) PTZ Presets
After manually setting up a shot that you
would like to return to later,you can save
presets for quick recall of these
positions. Type a number between 0 and
254 into the Preset box. Click
the“Set”button to save the current
location with that preset number. Click
the “Call” button to cause the camera to
return to that position. This enables
smooth, quick and convenient control
without the need to manually drive the
camera.
You can set up preset that user want as
below.
Method: Type preset number into the
Preset box.
Preset: Optional items: 0 ~ 254.
6) PTZ/OSD Dropdown
From the dropdown menu, clicking the
OSD option will open the on-screen
display menu of the camera giving you
control from within the IP interface.
C. Language Selection
Click either “Chinese”, “English” or
“Russian” to change the language of the
webpage.
7.3 Video Settings
1) Video Format
Support Dial Priority.
2) Low Latency Mode
Turn On/Offlow latency mode, the OSD
function will not be enabled after it is
turned on.
3) Encode Level
Support baseline, mainprofile,
highprofile and svc-t four levels.
4) Encode Protocol
Support H.264and H.265protocols.
5) Resolution
First stream support 1920x1080,
1280x720, 1024x576, 960x540,
640x480, 640x360.Second stream
support1280x720, 1024x576, 720x480,
640x360, 480x272, 320x240, 320x180;
The bigger resolution is, the clearer the
image will be, more network bandwidth
will be taken.
Set Call
Preset
Language 中文(简)
Русский
English
Video Settings
First stream
Encode Level
mainprofile
23
SliceSize
H264
EncodeProtocol
1920x1080
Resolution
8192
BitRate
60
FrameRate
50
I Key Frame Interval
CBR
Bit RateControl
off
SliceSplit Enable
Submit Cancel
Secondstream
mainprofile
Encode Level
23
SliceSize
H264
EncodeProtocol
640x360
Resolution
1024
BitRate
30
FrameRate
30
I Key Frame Interval
CBR
Bit RateControl
off
SliceSplit Enable
LowLatencyMode On
Dial Priority
VideoFormat
Off
(TheOSDfunction will not beenabled after it isturned on)

1080P HD PTZ Camera User Manual
17
6) Bit Rate
The user can specify the bit rate.
Generally speaking, the larger of the bit
rate, the clearer of the image. However,
the configuration of the bit rate needs to
be combined with the network
bandwidth. When the network
bandwidth is narrow and the bit rate is
configuredlarger, the video stream
cannot be transmitted normally, and the
visual effect is worse.
7) Frame Rate
User can specify the size of the frame
rate, generally, the frame rategreater,
the image more smooth; Frame rate is
smaller, the more sense of beating.
8) I Key Frame Interval
Set interval between 2 I frame,the bigger
interval isthe response will be lower from
viewing window.
9) Bit Rate Control
Code stream control way:
CBR (Constant Bit Rate): Video coder will
be coding according to preset speed.
VBR(Variable Bit Rate): Video coder will
adjust the speed based on preset speed
to gain the best image quality.
10)Slice Split Enable
Enable or disable slice split function.
11) Slice Size
Set the size of slice.
7.4 Image Settings
1) Brightness
Brightnessof image: 0~99 (Default value
is 50).
2) Saturation
Saturationof image: 0~200 (Default
value is 100).
3) Contrast
Contrastof image: 0~99 (Default value is
50).
4) Sharpness
Sharpnessof image: 0~99 (Default value
is 20).
5) Hue
Hueof image: 0~99 (Default value is 50).
6) Flip
Turn On/Offthe Flip function.
7) Mirror
Turn On/Offthe Mirror function.
7.5 Audio Settings
Saturation +
-100
Brightness +
-50
Contrast +
-50
Sharpness +
-20
Hue +
-50
Flip On Off
Mirror On Off
Submit Cancel Default