Prestige APS901Z User manual

1APS901Z Owners rev A.
IMPORTANT NOTE: The operation of the Security and Convenience System as described in this manual is
applicable to most vehicles. However, due to the conguration of some vehicles, some functions AND/OR
SAFETY PRECAUTIONS may not apply. Please see your installing dealer for more information.
Owner’s Guide
For Model:
APS901Z
Remote Start System

22018 Voxx Electronics Corporation. All rights reserved.
Table of Contents
Using Your Remote Control .......................................................3
Optional Security Control ..........................................................4
Remote Control Programming...................................................5
Replacing Remote Control Batteries ........................................5

3APS901Z Owners rev A.
Using Your Remote Control
Door Unlock
While the engine is running press and release and hold the button or 3 seconds.
Unlock is only avaiable while the vehicle is remote started.
Remote Starting Your Vehicle
To activate the remote start, press and release the button 2 times. The vehicle will
start and run the predetermined time set up during installation (5 to 60 minutes
selectable).
Remote Start Shutdown
Press and release the button two times to turn the vehicle o󰀨. Pressing the
vehicle’s brake will also shutdown the remote start.
Entering the Vehicle while it is Running via Remote Vehicle Start
1. Unlock the vehicle’s doors.
2. Enter the vehicle. DO NOT PRESS THE BRAKE PEDAL!
3. Insert the key into the ignition switch and turn to the ON or RUN
position.
4. Press the brake pedal. The remote vehicle starter will disengage and
the vehicle will operate normally.
NOTE: This feature may not be available on all vehicle makes/models. In some
vehicle applications the the remote start will shut down upon entering the vehicle and
the engine will stop running. For these applications it will be necessary to restart the
vehicle normally. Refer to installing dealer for details.
Preheating or Precooling the Vehicle’s interior
Before exiting the vehicle, set the temperature controls to the desired setting and
operation. After the system starts the vehicle, the heater or air conditioner will
activate and heat or cool the vehicle’s interior to your setting.

42018 Voxx Electronics Corporation. All rights reserved.
Security Upgrade (Optional)
System Arm
To Arm and lock the vehicle doors press and release the button 1 time. The LED
on the antenna will ash one time while armed.
System Disarm
To Disarm and unlock the vehicle doors press and release the button 2 times.
System Override
To disarm the system without the use of the remote control locate the valet override
button on the windshied mounted antenna.
1. Entery the vehicle
2. Turn the vehicle ignition to the ON position.
3. Press and release the valet button in the antenna 1 time.
The system is not disarmed and will remain disarmed until the button is pressed.
Valet Mode
Valet mode allows the user to Lock or Unlock the vehicle without Arming the security
system. To enter or exit valet mode:
1. Turn the vheicle ignition to the ON position
2. Press and hold the valet button for 5 seconds. The LED on the antenna
will turn on solid.
Remote Starting Your Vehicle
To activate the remote start, press and hold the button for 3 seconds. The vehicle
will start and run the predetermined time set up during installation (5 to 60 minutes
selectable).
Remote Start Shutdown
Press and hold the button for 3 seconds to turn the vehicle o󰀨. Pressing the
vehicle’s brake will also shutdown the remote start.

5APS901Z Owners rev A.
Remote Control Programming
Replacing Remote Control Batteries
1 Button Remote Control - Model 181SP
The CR2032 battery inside each remote control should last approximately 1 year under
normal use. When the battery becomes weak you will notice the remote control range
(the distance from the vehicle the remote control will work) deteriorate and the small LED
on the remote control will dim. To replace the remote control batteries:
1. Using a coin, disassemble the halves of the remote
control.
2. Remove the old battery, observing the +/- symbols on the
batteries and replace with a new battery.
3. Reassemble the halves of the remote control
4. Test operation of the remote control.
1. Cycle the vehicle ignition ON.
2. Press and release the Valet button 3x.
2. Press 1 button of each transmitter you wish to program, the LED’s will
ash to conrm each transmitter.
3. Turn the vehicle ignition OFF.
NOTE: This system has 1 button programming which programs all channels of the
system.
NOTE: The system will hold up to 4 transmitters in memory, programming a 5th
transmitter will erase the oldest transmitter in memory.

62018 Voxx Electronics Corporation. All rights reserved.
Voxx Electronics Corporation.
Customer Service 1-800-225-6074
www.PrestigeCarSecurity.com
FCC COMPLIANCE
This device complies with Part 15 of the FCC rules and with RSS-210 of
Industry Canada. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including any interference that
may cause undesired operation.
Warning!
Changes or modications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
PATENTED: www.voxxintl.com/company/patents