Primo Water 900178 User manual

Model # 900178: Page 1
PN O-029 © 2009 Primo Water Corporation
TO REDUCE THE RISK OF INJURY AND
PROPERTY DAMAGE, USER MUST READ
THIS MANUAL BEFORE ASSEMBLING,
INSTALLING & OPERATING DISPENSER.
SAVE THIS MANUAL FOR
FUTURE USE
USER MANUAL
Bottom Loading
Bottled Water Dispenser
Model # 900178

Model # 900178: Page 2
SAFETY PRECAUTIONS
To reduce risk of injury and property damage, user must read this entire
manual before assembling, installing & operating dispenser.
Failure to execute the instructions in this manual can cause personal injury
or property damage.
This product dispenses water at very high temperatures. Failure to use
properly can cause personal injury.
When operating this dispenser, always exercise basic safety precautions,
including the following:
• Prior to use, this dispenser must be properly assembled and installed in accordance with
this manual.
• This dispenser is intended for water dispensing only. Do NOT use other liquids. Do NOT
use for other purposes. Never use any other liquid in the dispenser other than known and
microbiologically safe bottled water.
• For indoor use only. Keep water dispenser in a dry place away from direct sunlight. Do NOT
use outdoors.
• Install and use only on a hard, flat and level surface.
• Do NOT place dispenser into an enclosed space or cabinet.
• Do NOT operate dispenser in the presence of explosive fumes.
• Position back of dispenser no closer than 4 inches from wall and permit free airflow
between wall and dispenser. There must be at least 4 inches clearance on the sides of the
dispenser to permit airflow.
• Use only properly grounded outlets.
• Do not use an extension cord with your water dispenser.
• Always grasp plug and pull straight out from outlet. Never unplug by pulling on power cord.
• Do NOT use dispenser if cord becomes frayed or otherwise damaged.
• To protect against electric shock, do NOT immerse cord, plug, or any other part of cooler in
water or other liquids.
• Ensure dispenser is unplugged prior to cleaning.
• Never allow children to dispense hot water without proper and direct supervision. Unplug
unit to prevent unsupervised use by children.
• Service should be performed only by a certified technician. Please contact us at
866-429-7566 for assistance.

Model # 900178: Page 3
TABLE OF CONTENTS
Safety Precautions …………………………………………… 2
Key Information for Future Use ……………………………. 3
Specifications ………………………………………………… 4
Parts & Features …………………………………………….. 4
Assembly ……………………………………………………… 5
Installation ……………………………………………………. 5
Operation …………………………………………………….. 5
Proper Care & Cleaning ……………………………………. 9
Troubleshooting ……………………………………………… 11
Limited Warranty ……………………………………………… 12
KEY INFORMATION FOR FUTURE USE
Please register your dispenser immediately at
www.primowater.com.
For future support please record your serial number (located on
label on back of dispenser) and date purchased. Staple your
receipt to manual.
You will need this information to obtain warranty service.
Product Bottom Loading
Bottled Water Dispenser
Model Number 900178
Serial ID Number
Date of Purchase

Model # 900178: Page 4
SPECIFICATIONS
Power Supply 5 AMPs
Refrigerant Type R-134A
Cold Water Power 125 Watts
Cold Capacity / Hour 1.0 Gallons
Cold Temp Range 39°F – 59°F
Hot Water Power 425 Watts
Hot Capacity / Hour 1.0 Gallons
Hot Temp Range 149°F – 199°F
Dimensions 40.5 inches H x 12.6 inches W x 15.0
inches D
Net Weight 37.5lbs.
PARTS & FEATURES
Energy Saving Switch - Cold
Front Back
LED Nightlights
Bottle Tray (Inside)
Bottle Probe (Inside Cabinet)
Control: Hot Water
Tap; Hot Water
Drip Tray
1
2
3
4
5
6
7
8
10
Drain Plug
Carry Handle
Power Cord
1
2
465
7
8
9
13
15
10
14
11
12
13
Control: Cold Water
12
15
Door
11
Energy Saving Switch - Hot
9
Hot Water Release 3
14
Tap: Cold Water

Model # 900178: Page 5
ASSEMBLY
Keep plastic bags away from children.
1. Remove dispenser from packaging.
2. Unpack drip tray and insert into dispenser.
3. Remove protective packaging from around probe.
4. Properly dispose all of packaging.
INSTALLATION
1. Place dispenser upright.
2. Locate dispenser on a hard and level surface in a cool shaded location near a
grounded wall outlet.
3. Position dispenser so the back is at least 4 inches from wall and there are at least 4
inches of clearance on both sides.
4. To minimize vibration and noise, make sure dispenser is level.
Notice: Do NOT plug in power cord yet.
OPERATION
This unit is intended for water dispensing only. Do NOT use other liquids. Do NOT
use for other purposes.
This dispenser has been designed to use water bottles with 3, 5 and 5.2 gallon
capacity. Do NOT use alternative bottles.

Model # 900178: Page 6
Initial Set Up
Do NOT plug in until steps 1-3 are completed.
1. Allow unit to sit upright for 4 hours.
2. Set probe length (see illustration 1):
•If using a 5 gallon round bottle, use the probe as it is supplied.
•If using a 5 gallon rectangular bottle, remove section C. Save for
future use.
•If using a 3 gallon bottle, remove sections C & B. Save for future
use.
3. Install bottle:
•Open door and place fresh bottle in front of tray.
•Clean fresh bottle with a soft cloth and warm soapy water then rinse.
•Remove entire plastic cap from top of bottle.
•Insert probe into bottle.
•Push down on probe until it is seated.
•Create a seal by turning handle clockwise until tight – do NOT over tighten.
•Slide bottle onto tray and close door completely.
NOTICE: When using a 5 gallon rectangular bottle, slide into place as shown in
illustration 2.

Model # 900178: Page 7
4. Plug cord into a properly grounded wall outlet.
•The unit will come ON and start pumping air into the bottle.
•The air will force water from the bottle into the hot and cold water reservoirs.
5. Turn energy saving switches on back of dispenser to ON.
•The red switch controls the heating of water. If you do not want hot water, leave
this switch OFF.
•The blue switch controls the cooling of water. If you do not want cold water,
leave this switch OFF.
Notice:
•For unit to operate properly the probe head must have an air tight seal on the
bottle and the door must be fully closed.
•It will take up to 3 minutes for the reservoirs to load. During this time the pump
will run on and off. This is normal.
•Each time you dispense water from the taps, the pump will come on to refill the
tanks. This is normal.
Initial Rinsing of Water Lines
This unit has been tested and sanitized prior to packing and shipping. During transit dust
and odors can accumulate in the tank and lines. Dispense and dispose at least one
quart of water from cool and cold taps prior to drinking any water.
Dispensing Cold Water
Note: After setup, it will take 1 hour to get water to maximum cold temperature. During
this time the compressor may run continuously. This is normal.
1. Position bottle, glass, pitcher or cooking pot securely below cold water tap.
•The right triangle below the cold water control indicates the location of the cold
water tap.
•The circular shapes in the drip plate help align the flow of water. This unit
dispenses water at a fast rate. To avoid splashes, hold cup as close to the tap
as possible.
2. Depress right control downward to start flow.
3. Release control once desired fill level is achieved.

Model # 900178: Page 8
Dispensing Hot Water
This unit dispenses water at temperatures that can cause severe burns. Avoid
direct contact with hot water. Keep children and pets away from unit while
dispensing. Never allow children to dispense hot water without proper and direct
supervision.
Note: After setup, hot water will be available in 15-20 minutes.
1. Position bottle, glass, pitcher or cooking pot securely below hot water tap.
•The left triangle below the hot water control indicates the location of the hot
water tap.
•The circular shapes in the drip plate help align the flow of water. This unit
dispenses water at a fast rate. To avoid splashes, hold cup as close to the tap
as possible.
2. Push hot water release button (red) inward and depress control downward to start
flow.
3. Release control once desired fill level is achieved.
Replacing an Empty Bottle
Notice: When your bottle is empty the dispenser will beep 3 times and the LED
nightlights will blink until a fresh bottle is connected.
You may also hear a sucking sound when the bottle empties. This is normal and is
another way to be alerted that your bottle is empty. Replace empty bottle as soon as you
notice it is empty. There may be a small amount of water left in the bottle.
1. Open door and slide bottle out.
2. Remove probe from bottle:
•Turn handle counter-clockwise till loose.
•Pull probe straight up until completely out of bottle.
3. Install fresh bottle:
•Place fresh bottle in front of tray.
•Clean fresh bottle with a soft cloth and warm soapy water then rinse.
•Remove entire plastic cap from top of bottle.
•Insert probe into bottle.
•Push down on probe until it is seated.
•Create a seal by turning handle clockwise until tight – do NOT over tighten.
•Slide bottle onto tray and close door completely.

Model # 900178: Page 9
PROPER CARE & CLEANING
General Cleaning
Perform: As needed
Time Required: 5 minutes.
Note: Do NOT use abrasive materials or chemical cleaners.
1. Clean cabinet surfaces with a soft cloth and warm soapy water.
2. Wipe dust from back of dispenser to improve efficiency.
3. Remove drip tray assembly by sliding it forward. Remove cover. Place tray and
cover in dishwasher or wipe parts clean with a soft cloth and warm soapy water.
Cleaning Water Tanks and Lines
Perform: Every 3 months or whenever an off-taste occurs.
Time Required: 30 minutes.
Requires: (1) empty 5 gallon bottle, (1) 2 gallon or larger bucket, clean cloths and
unscented household bleach.
Note: Best to do prior to loading a fresh bottle.
Step A: Remove Existing Water
1. Move dispenser away from wall and turn it 90°in either direction.
2. Turn energy saving switches to OFF.
3. Unplug power cord from wall outlet.
4. Remove water bottle and disconnect probe.
5. Place a 2 gallon or larger bucket under the drain plug
in the rear of the dispenser.
6. CAUTION: Remove drain cap and silicon plug. Cold
water will immediately flow into the bucket. Several
seconds’ later hot water will dispense.
Reminder - Place drain cap and silicon plug in a safe
location so they are not lost.
7. Once unit has drained, replace silicon plug and drain
cap.
8. Remove remaining water from reservoir by
dispensing from the cold and cool taps into a pitcher.
Step B: Sanitize Probe and Taps
1. In a clean bucket, make a sanitizing solution of one gallon tap water and 3
tablespoons of unscented household bleach.

Model # 900178: Page 10
2. Wipe probe and area around all 3 taps with a soft cloth moistened with the
sanitizing solution.
Step C: Sanitize Reservoirs
1. Remove the cap from a spare empty 5 gallon bottle.
2. Fill the bottle with sanitizing solution.
3. Insert probe into bottle and secure by tightening handle clockwise.
4. Slide bottle into cabinet and close door.
5. Plug power cord into a grounded wall outlet.
6. Turn energy saving switches ON.
7. Allow the water and bleach mixture to fill the empty reservoirs.
8. Wait 10 minutes then turn energy saving switches OFF and unplug the power cord.
9. Place a 2 gallon or larger bucket under the drain plug in the rear of the dispenser.
10. CAUTION: Remove drain cap and silicon plug. Cold water will immediately flow into
the bucket. Several seconds’ later hot water will dispense.
Reminder - Place drain cap and silicon plug in a safe location so they are not lost.
11. Once unit has drained, replace silicon plug and drain cap.
12. Remove remaining water from reservoir by dispensing from the cold and cool taps
into a pitcher.
Step D: Rinse Reservoirs
1. Dispose of sanitizing solution and rinse bottle with tap water.
2. Fill the bottle with tap water and insert probe into bottle.
3. Push down on probe until it is seated.
4. Create a seal by turning handle clockwise until tight – do NOT over tighten.
5. Slide bottle into cabinet and close door.
6. Plug power cord into a grounded wall outlet.
7. Allow the water and bleach mixture to fill the empty reservoirs.
8. Wait 10 minutes then turn energy saving switches OFF and unplug the power cord.
9. Place a 2 gallon or larger bucket under the drain plug in the rear of the dispenser.
10. CAUTION: Remove drain cap and silicon plug. Cold water will immediately flow into
the bucket. Several seconds’ later hot water will dispense.
Reminder - Place drain cap and silicon plug in a safe location so they are not lost.
11. Once unit has drained, replace silicon plug and drain cap.
12. Remove remaining water from reservoir by dispensing from the cold and cool taps
into a pitcher.
13. Return the unit to its location, install a fresh water bottle, plug the power cord back
into the grounded wall outlet and turn the energy saving switches ON.

Model # 900178: Page 11
TROUBLESHOOTING
Dispenser does not operate.
•Make sure the power cord is properly connected to a working outlet.
Water is leaking.
•Bottle may have a leak. Remove bottle and replace with new bottle.
•If leak remains, remove probe from bottle and call 866-429-7566 for assistance.
No water is coming from the taps.
•Make sure the bottle is not empty. If so, replace it.
•Make sure to push the water controls in fully.
•Make sure the probe connection with the water bottle forms a complete seal.
•Make sure the door is closed.
Cold water is not cold.
•It takes up to one hour after setup to secure cold water.
•Make sure the back of the dispenser is at least 4 inches from a wall and there is
free airflow on all 4 sides of the dispenser.
•Make sure energy saving switch is ON.
Hot water is not hot.
•It takes 15-20 minutes after setup to secure hot water.
•Make sure the power cord is properly connected to a working outlet.
•Make sure energy saving switch is ON.
Dispenser is noisy.
•Make sure dispenser is level.
Water tastes bad.
•Drain water from reservoirs and replace bottle with a fresh one.
•Sanitize dispenser per Proper Care & Cleaning instructions.
Nightlight Isn’t Working
•Make sure the power cord is properly connected to a working outlet.
•Bulb could be out. Call 866-429-7566 for assistance.
Nightlight Is Flashing
•This indicates bottle is empty. Replace bottle.

Model # 900178: Page 12
LIMITED WARRANTY
Primo Water Corporation, (“Vendor”) warrants to the original purchaser of this dispenser, and to
no other person, that if this dispenser is assembled and operated in accordance with the printed
instructions accompanying it, then for a period of two (2) years from the date of purchase, all parts
in such dispenser shall be free from defects in material and workmanship. Vendor may require
reasonable proof of your date of purchase from an authorized retailer or distributor. Therefore, you
should retain your sales slip or invoice. The Limited Warranty shall be limited to repair or
replacement of parts, which prove defective under normal use and service and which Vendor shall
determine in its reasonable discretion upon examination to be defective. Before returning any parts,
you should contact Vendor’s Customer Service Department using the contact information listed
below. If Vendor confirms, after examination, a defect covered by this Limited Warranty in any
returned part, and if Vendor approves claim, Vendor will replace such defective part without charge.
If you return defective parts, transportation charges must be prepaid by you. Vendor will return
replacement parts to original purchaser, freight or postage prepaid.
The Limited Warranty does not cover any failures or operating difficulties due to accident, abuse,
misuse, alteration, misapplication, improper installation or improper maintenance or service by you
or any third party, or failure to perform normal and routine maintenance on the dispenser, as set out
in the User’s Manual. In addition, the Limited Warranty does not cover damages to the finish, such
as scratches, dents, discoloration or rust after purchase.
The Limited Warranty is in lieu of all other express warranties. Vendor disclaims all warranties for
products that are purchased from seller other than authorized retailers or distributors. AFTER THE
PERIOD OF THE TWO (2) YEAR EXPRESS WARRANTY, VENDOR DISCLAIMS ANY AND ALL
IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION THE IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. FURTHER, VENDOR
SHALL HAVE NO LIABILITY WHATSOEVER TO PURCHASER OR ANY THIRD PARTY FOR
ANY SPECIAL, INDIRECT, PUNITIVE, INCIDENTAL, OR CONSEQUENTAL DAMAGES. Vendor
assumes no responsibility for any defects caused by third parties. This Limited Warranty gives the
purchaser specific legal rights; a purchaser may have other rights depending upon where he or she
lives. Some jurisdictions do not allow exclusion or limitation of special, incidental or consequential
damages, or limitations on how long a warranty lasts, so the above exclusion and limitations may
not apply to you.
Primo Water Corporation
104 Cambridge Plaza Drive
Winston-Salem, NC 27104
866-429-7566
www.primowater.com

Modelo no900178: Página 1
PN O-029 © 2009 Primo Water Corporation
PARA REDUCIR EL RIESGO DE LESIONES
Y DAÑOS MATERIALES, EL USUARIO
DEBE LEER ESTE MANUAL ANTER DE
ENSAMBLAR, INSTALAR Y USAR EL
DISPENSADOR.
GUARDAR ESTE MANUAL
PARA USO FUTURO
MANUAL DEL USUARIO
Dispensador de agua con
carga por la parte inferior
Modelo no900178

Modelo no900178: Página 2
PRECAUCIONES DE SEGURIDAD
Para reducir el riesgo de lesiones o daños materiales, el usuario debe leer
este manual por completo antes de ensamblar, instalar y usar el dispensador.
No seguir las instrucciones de este manual puede causar lesiones o daños
materiales.
Este producto dispensa agua a temperaturas muy altas. El uso incorrecto
puede causar lesiones.
Cuando use este dispensador, siempre tome las precauciones de seguridad
básicas, incluidas las siguientes:
•Antes de usarse, este dispensador debe ensamblarse e instalarse de acuerdo con este
manual.
•Este dispensador está diseñado para dispensar agua únicamente. NO usar otros
líquidos. NO usar para otros propósitos. No use ningún otro líquido en el dispensador
que no sea agua embotellada y microbiológicamente segura.
•Para uso en interiores. Mantenga el dispensador de agua en un lugar seco y alejado de
la luz solar directa. NO usar en exteriores.
•Instalar y usar únicamente sobre superficies duras, niveladas y planas.
•NO instalar el dispensador en espacios o gabinetes cerrados.
•NO use este dispensador en presencia de gases explosivos.
•Posicionar la parte posterior del dispensador a una distancia de por lo menos 4
pulgadas (10 cm) de la pared para permitir el flujo de aire entre la pared y el
dispensador. Debe haber por lo menos 4 pulgadas (10 cm) de espacio libre a los lados
del dispensador para permitir el flujo de aire.
•Usar únicamente tomacorrientes con conexión a tierra.
•No utilice un cable de extensión con el dispensador de agua.
•Siempre tomar el enchufe y tirar de él en línea recta del tomacorriente. Nunca
desenchufar tirando del cable.
•NO usar el dispensador si el cable está raído o dañado de alguna manera.
•Para protegerse contra el choque eléctrico, NO sumergir el cable, el enchufe o cualquier
otra parte del dispensador en agua u otros líquidos.
•Asegurarse de que el dispensador esté desenchufado antes de limpiarlo.
•Nunca permita que los niños dispensen agua caliente sin supervisión adecuada y
directa. Desenchufe la unidad para evitar que la usen niños sin supervisión.
El servicio debe hacerse solamente por técnicos certificados. Comuníquese con nosotros
llamando al 866-429-7566 para obtener ayuda.

Modelo no900178: Página 3
ÍNDICE
Precauciones de seguridad………………………………… 2
Información importante para uso futuro……………………. 3
Especificaciones……………………………………………… 4
Piezas y características…………………………………….. 4
Ensamblaje…………………………………………………… 5
Instalación……………………………………………………. 5
Operación…………………………………………………….. 5
Cuidado y limpieza……..……………………………………. 9
Resolución de problemas…………………………………… 12
Garantía limitada……………………………………………… 13
INFORMACIÓN IMPORTANTE PARA USO FUTURO
Por favor registre su dispensador inmediatamente en
www.primowater.com.
Para servicio futuro, por favor registre su número de serie
(ubicado en la etiqueta situada en la parte posterior del
dispensador) y la fecha de compra. Engrape su recibo al
manual.
Necesitará esta información para obtener servicio de garantía.
Producto Dispensador de agua
con carga por la parte inferior
Número de modelo 900178
Número de serie
Fecha de compra

Modelo no900178: Página 4
ESPECIFICACIONES
Fuente de energía eléctrica 5 amperios
Tipo de refrigerante R-134A
Potencia agua fría 125 vatios
Capacidad enfriam. / hora 1 galón (3,8 litros)
Rango temp. fría 39°F – 59°F (4°C – 15°C)
Potencia agua caliente 425 vatios
Capacidad calent. / hora 1 galón (3,8 litros)
Rango temp. caliente 149°F – 199°F (65°C – 93°C)
Dimensiones 40,5 pulgadas de alto x 12,6
pulgadas de largo x 15
pulgadas de ancho (102,9 cm x
32cm x 38,2 cm)
Peso neto 37,5libras (17kg)
PIEZAS Y CARACTERÍSTICAS
–Interruptor de ahorro de energía - Frío
Frente Atrás
Luces LED nocturnas
Bandeja de botellón (dentro)
Sonda de botellón (dentro del gabinete)
Control de agua caliente
Grifo de agua caliente
Bandeja de goteo
1
2
4
5
6
7
8
9
10
12
Tapón de drenaje
Asa
Cable eléctrico
1
2
465
7
8
9
13
15
10
14
13
14
15
Control de agua fría
12
Puerta
11
Interruptor de ahorro de energía - Caliente
11
Botón de liberación de agua caliente
3
3
Grifo de agua fría

Modelo no900178: Página 5
ENSAMBLAJE
Mantener las bolsas plásticas fuera del alcance
de niños.
1. Saque el dispensador del empaque.
2. Desempaque la bandeja de goteo e inserte en el
dispensador.
3. Retire el material de embalaje protector que se encuentra alrededor de la sonda.
4. Deseche el material de embalaje como es debido.
INSTALACIÓN
1. Coloque el dispensador en posición vertical.
2. Coloque el dispensador encima de una superficie dura y nivelada en una ubicación
protegida y fresca cerca de un tomacorriente con conexión a tierra.
3. Coloque el dispensador de modo que la parte posterior esté a una distancia de por
lo menos 10 cm de la pared y que ambos lados tengan un espacio libre de por lo
menos 10 cm.
4. Para minimizar la vibración y el ruido, asegúrese de que el dispensador esté
nivelado.
Aviso: Todavía NO enchufe el cable eléctrico.
OPERACIÓN
Esta unidad está diseñada para dispensar agua únicamente. NO usar otros
líquidos. NO usar para otros propósitos.
Este dispensador está diseñado para usarse con botellones de 3, 5 y 5,2 galones
(13,2,3 ó 19,6 litros) de capacidad. NO use botellones alternativos.
Encendido inicial
NO enchufe la unidad hasta que haya realizado los pasos 1 al 3.

Modelo no900178: Página 6
1. Permita que la unidad repose en posición vertical durante 4 horas.
2. Fije la longitud de la sonda (vea la ilustración 1):
•Si está usando un botellón redondo de 5 galones (18,9 litros), use
la sonda tal como se ha suministrado.
•Si está usando un botellón rectangular de 5 galones (18,9 litros),
retire la sección C. Guárdela para uso futuro.
•Si esta usando un botellón de 3 galones (11,3 litros), retire las
secciones C y B. Guárdelas para uso futuro.
3. Instale el botellón:
•Abra la puerta y coloque un botellón nuevo en frente de la bandeja.
•Limpie el botellón nuevo con un paño suave y aja jabonosa tibia, luego
enjuague.
•Quite del botellón la tapa de plástico completa.
•Inserte la sonda dentro del botellón.
•Presione hacia abajo la sonda hasta que encaje.
•Cree un sello girando el asa en dirección de las manecillas del reloj hasta que
esté firme – NO apriete excesivamente.
•Deslice el botellón sobre la bandeja y cierre completamente la puerta.
AVISO: Cuando use un botellón rectangular de 5 galones (18,9 litros), deslícelo a
su lugar como se muestra en la ilustración 2.

Modelo no900178: Página 7
4. Enchufe el cable en un tomacorriente de pared conectado a tierra.
•La unidad se suministra encendida y comenzará a bombear aire en el botellón
•El aire forzará agua del botellón a los depósitos de agua caliente y fría.
5. Coloque en la posición ON (encendido) los interruptores de ahorro de energía
situados en la parte posterior del dispensador.
•El interruptor rojo controla el calentamiento del agua. Si no desea agua caliente,
deje este interruptor en la posición OFF (apagado).
•El interruptor azul controla el enfriamiento del agua. Si no desea agua fría, deje
este interruptor en la posición OFF (apagado).
Aviso:
•Para que la unidad funcione correctamente, el cabezal de la sonda debe tener
un sello hermético de aire en el botellón y la puerta debe estar completamente
cerrada
•Los depósitos tardarán hasta 3 minutos en cargar. Durante este tiempo la
bomba se encenderá y apagará. Esto es normal.
•Cada vez que dispense agua de los grifos, la bomba se encenderá para rellenar
los tanques. Esto es normal.
Enjuague inicial de las líneas de agua
Esta unidad ha sido probada y desinfectada antes de su empaque y envío. Sin embargo,
es posible que durante el transporte se acumulen polvo y olores en el tanque y en las
líneas. Dispense y deseche por lo menos un cuarto de galón (aprox. 1 litro) de agua de
los grifos de agua tibia y fría antes de beber el agua.
Dispensar agua fría
Aviso: Después del encendido inicial, el agua demorará una hora en llegar a la
temperatura fría máxima. Durante este tiempo, el compresor quizás funcione
continuamente. Esto es normal.
1. Coloque una botella, vaso, jarra u olla de manera segura debajo del grifo de agua
fría.
•El triángulo derecho debajo del control de agua fría indica la ubicación del grifo
de agua fría.
•Las formas circulares en la bandeja de goteo ayudan a alinear el flujo de agua.
Esta unidad dispensa agua de forma rápida. Para evitar salpicaduras, acerque
el vaso lo más posible al grifo.
2. Presione el control derecho hacia abajo para empezar el flujo.
3. Suelte el control una vez que se alcance el nivel de agua deseado.

Modelo no900178: Página 8
Dispensar agua caliente
Esta unidad dispensa agua a temperaturas que pueden causar quemaduras
severas. Evite el contacto directo con el agua. Mantenga a niños y animales
alejados de la unidad mientras dispensa agua caliente. Nunca permita que los
niños dispensen agua caliente sin la debida supervisión directa.
Aviso: Después del encendido inicial, el agua caliente estará disponible después de 15-
20 minutos.
1. Coloque una botella, vaso, jarra u olla de manera segura debajo del grifo de agua
caliente.
•El triángulo izquierdo debajo del control de agua caliente indica la ubicación del
grifo de agua caliente.
•Las formas circulares en la bandeja de goteo ayudan a alinear el flujo de agua.
Esta unidad dispensa agua de forma rápida. Para evitar salpicaduras, acerque
el vaso lo más posible al grifo.
2. Presione hacia adentro el botón de liberación de agua caliente (rojo) y presione el
control hacia abajo para empezar el flujo.
3. Suelte el control una vez que se alcance el nivel de agua deseado.
Reemplazar un botellón vacío
Aviso: Cuando el botellón esté vacío, el dispensador emitirá un pitido 3 veces y
parpadearán las luces LED nocturnas hasta que se conecte un botellón nuevo.
También podría escuchar un sonido de succión cuando el botellón esté vacío. Esto es
normal y es otra manera de indicarle que el botellón está vacío.
Reemplace el botellón vacío tan pronto note que se acabó el agua.
Puede quedar una pequeña cantidad de agua en el botellón.
1. Abra la puerta y deslice el botellón hacia afuera.
2. Saque la sonda del botellón:
•Gire el asa en dirección contraria a las manecillas del reloj hasta que se afloje.
•Jale la sonda hacia arriba hasta que sacarla completamente del botellón.
3. Instale un botellón nuevo:
•Coloque un botellón nuevo frente a la bandeja.
•Limpie el botellón nuevo con un paño suave y agua jabonosa tibia, luego
enjuague.
•Extraiga la tapa de plástico completa del botellón.
•Inserte la sonda dentro del botellón.
•Presione hacia abajo la sonda hasta que encaje.
•Cree un sello girando el asa en dirección de las manecillas del reloj hasta que
esté firme. NO apriete demasiado.
•Deslice el botellón sobre la bandeja y cierre completamente la puerta.