Primula ECO DOB 3711 User manual

IRONING PRESSING MACHINERIES - FUSING PRESSES
Operating Manual
ECO DOB 3711 & ECO DOB 3711 E
www.ae-sewingmachines.co.uk

2
www.ae-sewingmachines.co.uk

3
Please read this instruction manual very carefully before you start using your new Ironing Table
ECO DOB 3711 & ECO DOB 3711 E
The customer by purchasing this product declares he is fully aware and accepts everything
mentioned in this operating manual.
Primula SA assumes no responsibility for any errors herein, nor for incidental or resulting
damage in connection with the performance or use of this operating manual.
You may not copy, reproduced, or translated this operating manual, or parts of it, to another
language without prior written consent of Primula SA.
The information in this document may change without notice.
1rst edition –September
Copyright 2014
Company name: Primula S.A
Address: 14th klm Thessaloniki –Kilkis,
57200 Liti, Thessaloniki, Greece
Industry: Ironing Equipment
Telephone: [phone]
Fax: [phone]
Web: www.primula.gr
E-mail: [email protected]r
ATTENTION!!!
www.ae-sewingmachines.co.uk

4
For the safe use of the Ironing Table, please read carefully the instructions that follow.
1. Install, use and maintain the ironing Table according to the instructions in this manual,
otherwise the manufacturer has no responsibility for the possible failed operation or safety.
2. Before connecting the power supply, control that the voltage corresponds to the voltage
indicated on the technical specifications label that is glued to the Ironing Table.
3. Connect the machine only to a power supply that has the minimum required frequency and
is properly grounded.
4. Use the system ONLY for the intended use according to this instruction manual and only with
the accessories that are provided or that are intended for this specific Ironing Table. The
manufacturer is not liable for any damages resulting from misuse or wrong use of the Ironing
Table.
5. DO NOT touch the power supply with wet hands.
6. Do not wash the Ironing Table with corrosive or other damaging materials.
7. For any malfunction or information request, please contact your dealer or the manufacturer.
8. Any kind of welding on the Ironing Table or its parts is strictly prohibited.
9. Never use the machine to support any other machine or structure.
10. It is strictly forbidden to remove any protective device.
11. It is strictly prohibited to intervene in the control units of the Ironing Table.
Primula S.A preserves the right to make changes to the Ironing Table and its parts without prior
notice.
GENERAL RULES AND WARNINGS
www.ae-sewingmachines.co.uk

5
1) Turn the ironing board (A) upside down, as seen bellow.
2) Assembly the stand (B) on top of it, by tightening all the screws.
3) Afterwards put the foot pedal base (C) of top of the stand and tighten all the screws
once again.
4) Turn the ironing table, the right side up.
Concerning the electrical connection and the power supply, please follow very carefully the
instructions of the technical specifications label attached to the Ironing table and the electrical
diagram on pages 12 for the ECO DOB 3711 E, and page 13 for the ECO DOB 3711.
Connect the plug of the power feeding cable to a proper grounded socket plug 230V, 16
Amber.
CAUTION! The manufacturer denies any liability for any injury or accident that might be caused
due to faulty power networks or due to faulty connections made by unauthorized personnel.
ASSEMBLY INSTRUCTIONS
ELECTRICAL CONNECTION
www.ae-sewingmachines.co.uk

6
Switch on the main switch (nr.1)
Switch on the thermostat knob (nr.3) at a temperature of 110°C during the winter and at
90°C during the summer.
Whenever you want to use suction/vacuum, just press the food pedal with your foot.
Adjust the steam quantity of your steam generator in proportion to the suction capacity
used on the ironing table, in order to avoid steam liquidation on the working surface.
Especially during the wintertime when the environment’s temperature is low and the
environment’s humidity is elevated.
The delicate fabrics require a small quantity of steam, while the rougher fabrics require
large quantity of steam.
The ironing buck’s heating is activated when you press the switch (nr 2) to position I.
If your Ironing Table is equipped with the optional Vario/Iron hanging System, then please
adjust it (through the balancer knob) so that the Iron levitates approximately 5 cm above
the ironing surface. Once you have finished ironing then unhook the iron from the Vario
System and put it to rest on the iron silicone mat.
OPERATING INSTRUCTION ECO DOB 3711
www.ae-sewingmachines.co.uk

7
Switch on the main switch (nr.1)
Switch the thermostat knob (nr 2) in its MAX position during the winter and in its MIN
position during the summer. The red led lamp (nr 3), will indicate when the heating is on.
When you want to inactivate the heating switch the thermostat knob (nr 2) to the zero (0)
position.
Whenever you want to use suction/vacuum, just press the food pedal with your foot.
Adjust the steam quantity of your steam generator in proportion to the suction capacity
used on the ironing table, in order to avoid steam liquidation on the working surface.
Especially during the wintertime when the environment’s temperature is low and the
environment’s humidity is elevated.
The delicate fabrics require a small quantity of steam, while the rougher fabrics require
large quantity of steam.
The ironing buck’s heating is activated when you press the switch (nr 5) to position I
If your Ironing Table is equipped with the optional Vario/Iron hanging System, then please
adjust it (through the balancer knob) so that the Iron levitates approximately 5 cm above
the ironing surface. Once you have finished ironing then unhook the iron from the Vario
System and put it to rest on the iron silicone mat.
OPERATING INSTRUCTION ECO DOB 3711 E
www.ae-sewingmachines.co.uk

8
Make sure that the covers of the ironing table and its buck(s) remain clean.
Wash the blue polyester fabric and the blue foam underneath, once a week in the washing
machine (30-40 oC).
In case you use felt molletone instead of blue foam, do not put it in the washing machine,
but wash by hand. Replace the covers and foam once they are worn out in order to keep
your high suction performance.
Clean the dust of the fan wheel/impeller (nr 2) at least 2-3 times per year.
Periodically clean and grease the bearings of the swivel arm and its buck(s).
Periodically clean the internal parts of the machine as well as the electronic circuit by using a
compressed air gun.
CAUTION! Before doing any maintenance work, please disconnect the Ironing Table from the
power supply!
The vacuum does not function properly
-Check if there is power supply 230V/1phase.
-Check if the power feeding cable (no 5) is for some reason cut off.
-Check the fuse (nr 7)
-Check if the suction’s button pedal (nr 21) is faulty: Replace it.
-Check if the motor (nr 1) is for some reason damaged.
The heating of the working surface is not activated.
-Check if the safety thermostat (nr 11) is faulty: Replace it
-Check if the thermostat (nr 10) is faulty. Replace it.
-Check if the heating element (nr 9) is burned out. Replace it.
-Check the fuse (nr 7) on the panel.
The heating of the ironing buck is not activated.
-Check the buck’s cable and plug.
-Check the switch (nr 8) which indicates the buck’s heating on the panel.
-Check the heating element of the ironing buck.
The motor functions loudly.
-Check if the ball bearings of the motor are faulty. Replace them.
-Check the impeller to be sure that there is no dust which could cause the vibration.
MAINTENANCE
TROUBLES SHOOTING
www.ae-sewingmachines.co.uk

9
For any advice about the operation of the machine or the spare parts, please contact the
dealer you have purchased the machine from or us directly at:
14th klm Thessaloniki –Kilkis, 57200 Liti, Thessaloniki, Greece
Tel.: [phone] Fax : [phone]
E-mail : [email protected]
All specifications have been made to the best of our knowledge.
Specifications may be subject to change without any prior notice.
TECHNICAL ASSISTANCE
www.ae-sewingmachines.co.uk

10
Spare parts list for ECO DOB 3711 & ECO DOB 3711 E
www.ae-sewingmachines.co.uk

11
ECO DOB 3711 & ECO DOB 3711 E- Spare parts list
Article nr.
Description
1
302-26-001
Motor 0,50HP 230V
2
302-26-002
Ιmpeller 160
3
192-26-003
Metallic shell
4
302-26-004
Thermostat’s knob
306-11-045
Thermostat’s knob only for Eco DOB E
5
302-26-005
Power feeding cable with plug 3X1,5
6
308-00-006
Switch ON-OFF 16A
7
302-26-007
FUSE 10A
8
302-22-054
Buck’s switch ON-OFF
9
302-01-014
Heating element 1KW 230V
10
302-00-012
Thermostat 110°C
302-01-011
Heating Probe only for Eco DOB E
11
302-01-010
Safety thermostat 145°C
12
302-26-012
Terminal block
13
192-27-013
Supporting corner 85
14
192-26-014
Perforated plate
15
302-06-015
Wire mesh plastic
16
302-01-029
302-01-031
302-01-031-4
Foam blue IFP-7mm
Felt molletone (optional)
Vacufix silicone SPF-6mm (optional)
17
302-01-030
Fabric cover
18
302-01-032
Cover’s rail
19
302-01-035
Spring with clips
20
192-26-020
Ironing table base
21
302-26-026
Vacuum button pedal MV45
22
192-26-022
Vacuum’s foot pedal
23
302-26-023
Foot pedal’s screw
24
302-26-024
Foot pedal’s spring
25
302-26-025
PC Board
26
302-02-014
Regulator Alignment adjusting leg
27
192-26-027
Balancer’s – trolley movement bar
28
302-00-049
Trolley of balancer
29
302-00-051
Balancer
30
102-26-033
Lightning system ED/LT
31
102-26-031
Swivel arm ED/AM 85
32
304-01-032
Form’s feeding cable
33
192-26-033
Swivel arm’s bearing
34
304-01-034
Safety thermostat 65ºC
35
304-01-035
Heating element 100W 230V
36
304-01-036
Perforated plate
37
304-01-037
Wire mesh plastic
38
304-01-038
304-01-038-1
304-01-038-2
Felt molletone
Foam blue IFP-7mm (optional)
Vacufix silicone SPF-6mm (optional)
39
304-01-039
Spring
40
304-01-040
Fabric cover
41
302-26-041
Stop for Balancer
42
302-26-042
Cable for lighting Eco DOB 3711 E
www.ae-sewingmachines.co.uk

12
Wiring Diagram
ECO DOB 3711 E
Symbol
code
Description
SW1
302-00-006
Main switch 16A
SW2
302-22-054
Buck’s switch ON-OFF
CV
302-26-005
Power feeding cable with plug 3X1,5
MV
302-26-026
Vacuum button pedal MV45
FP
302-04-045
3-poles plug for form connection
TS
302-01-010
Safety thermostat 145°C
M
302-26-001
Motor 0,50HP 230V
R
302-01-014
Heating element 1KW 230V
SP
302-01-011
Heating Probe only for Eco Dob/E
LT
102-26-033
Lightning system ED/LT
PC
302-26-025
PC Board
www.ae-sewingmachines.co.uk

13
www.ae-sewingmachines.co.uk