Primula FLEX FS S+B User manual

IRONING PRESSING MACHINERIES –FUSING PRESSES
INSTRUCTION MANUAL
FLEX FS S+B

2

3
A FEW WORDS FROM THE MANUFACTURER
The ironing table “FLEX FS”is a machine of high advanced technology, unique in its kind. It is
manufactured according to the International and European technical specifications and safety
standards from a company with experience since 1969 in its sector. Congratulations for your
choice!
INSTALLATION
Put the table in the required place and adjust the little foot Νο 13. Make sure, that is totally
aligned.
ELECTRICAL CONNECTION
For the electrical connection and everything about the power supply, please follow carefully the
instructions of the electric diagram attached to the machine. Please pay attention to the warning
signs symbols on the machine. In case you have a single phase machine 230V, connect the
machine to the power through the plug No 22 into the socket 230V/16A. The connection should
be done with 3-phase 3Χ1,5mm (1 phase, 1 neutral, 1 grounded). The power should be provided
with a fuse 10Α. If the machine is 400V/3 phase, the connection should be made to a 5-poles
cable 5Χ1,5mm (3 phase, 1 neutral, 1 grounding). The power should be secured with a 3-poles
safety switch (3Χ10Α).
CAUTION ! The manufacturer denies any liability for any injury or accident that might be
caused due to faulty power networks or due to faulty connections made by unskilled persons.

4
06 07 08 05
OPERATING INSTRUCTIONS
Turn on the main switch No. 06
Switch the thermostat No. 04 to temperature 110°C during the winter and to 90°C during the
summer.
Whenever you want to use the suction just press the left pedal No 22.
Adjust the steam quantity of the steam generator in proportion to the suction performance of
the table, in order to avoid steam liquidation on the working surface. The refined fabrics
require small quantity of steam, while the gross fabrics require big quantity of steam.
The ironing buck’s heating is activated when you press switch No 8 to position I.
In case the table disposes Vario iron’s lifting system (optional) hook the steam iron from the
balancer and adjust the distance of the steam iron from the working surface (approximately
5cm). After finishing ironing unhook the steam iron from the balancer and put it on the iron
rest mat.
*In case your table disposes a blowing system of air:
Adjust the volume of the blowing air with the lever according to the requirements of the fabric
(weight, quality , etc.) from the knob which is placed in the main body of the machine
In order to use the blowing push with your foot pedal No.
MAINTENANCE
Make sure that the covers of the table and the ironing buck remain clean, in order to have high
performance of suction and blowing air. Wash the blue polyester fabric and the foam blue once
in a week in the washing machine (30-40 οC).
In case you use felt molletone instead of blue foam, do not put it in the washing machine, but
wash it on hand. Replace them regularly, in order to keep high suction and blowing
performance.
Clean the dust of the fan wheel /impeller No 02 at least 2-3 times per year.
Periodically clean and grease the arm’s as well as the buck’s bearings.
Periodically clean the internal parts of the table as well as the electronic circuit by using
compressed air.
Keep the machine clean.
CAUTION! Before doing maintenance work, please disconnect the machine from the electrically
power supply.
04

5
TROUBLESHOOTING
The vacuum does not function properly
- Check if there is power supply
- Check if the power feeding cable is for some reason cut off
- Check the fuse 12Αwhich is inside the fuse case No 05
- Check if the suction’s button pedal No 9 is faulty
- Check if motor No 01 is for some reason damaged
- Check the relay Νο 13
- Check the electronic circuit Νο 18
The blowing of air does not function
- Check if the blowing’s button pedal No 9 is damaged
- Check the electronic circuit Νο 18
- Check the relay No 13
- Check the motor Νο 1
The heating of the working surface is not activated
- Check if the fuse 12Αinside the fuse case No 05 is burnt out. Replace it.
- Check if the safety thermostat No 40 is faulty. Replace it.
- Check if the thermostat No 64 is faulty. Replace it.
- Check if the heating element No 34 is burnt out. Replace it.
The heating of the ironing buck is not activated.
- Check the cable and the plug of ironing’s buck power supply
- Check the switch No 08 for the heating of the ironing buck
- Check the heating element of the ironing buck
The machine operates loudly
- Check if the ball bearings of the motor are faulty. Replace them.
- Check the impeller to be sure, that there is no dust which could cause the vibration.

6
1
2
4
5
6
7
8
9
10
11
12
13
14
17
18
19
20
22
60
61
62
63
21
PRIMULA
FLEX FS
SPARE PARTS

7
Spare parts list FLEX FS
Νο
CODE
DESCRIPTION
1
302-22-001
302-22-001-1
302-22-001-2
302-22-001-3
Electric Motor 0,75ΗΡ/400V/50HZ - 3 N
Electric Motor 0,75ΗΡ/230V/50ΗΖ - 1 Ν
Electric Motor 0,75ΗΡ/220V/60ΗΖ - 1 Ν
Electric Motor 0,75ΗΡ/110V/60HZ –1 N
2
302-22-002
Metallic cup
3
302-00-003
Fan wheel Ø180
4
302-22-004
Vacuum complete
5
192-22-005
Base of table 1365
6
192-22-006
Vacuum pedal 1365
7
192-22-007
Blowing pedal 1365
8
192-22-008
Terminal block for the connection of the vacuum button pedal
9
302-00-005
Vacuum button pedal
10
192-22-010
Base Νο 1 male
11
192-22-011
Base Νο 2 female
12
192-22-012
Label
13
302-00-010
Relay
14
192-22-014
Circuit’s case
15
192-22-015
Vacuum and Blowing interchange system
16
302-03-006
Flap Motor 12V/DC
17
192-22-017
Regulation lever of blowing
18
302-22-018
Electronic circuit
19
302-03-029
Socket 6A
20
302-22-020
4-poles corner socket
21
302-02-014
Leg for the regulation of table
22
302-22-022
302-00-014
Cable of power supply 3Χ1.5mm with plug
Cable of power supply 5Χ1.5mm
23
302-22-023
Power supply cable of heating element
24
192-22-024
Metallic base of iron
25
107-03-003
Silicon iron rest mat
26
302-00-041
Hanger of the iron’s cables
27
107-01-000
Antenna
28
192-22-028
Chimney
29
192-22-029
Tamber of chimney
30
31
192-22-031
Metallic cover
32
192-22-032
Board’s mechanic tamper
33
302-22-033
Springs with clips
34
302-01-014
Heating element 1KW 230V
35
192-22-035
Board 1365
36
192-22-036
Metallic gauze
37
302-22-037
Lattice fabric white
302-22-038
Foam layer 1365

8
Νο
CODE
DESCRIPTION
38
302-22-038-1
302-22-038-2
Vacufix layer 1365
Felt molletone 1365
39
302-22-039
Cover Fabric of board blue TPF-POL
40
302-01-010
Safety thermostat 145ºC
41
192-22-041
Corner’s tamper
42
192-22-042
Swivel arm’s corner
43
192-22-043
Swivel arm’s bronze gasket
44
192-22-046
Bearing of swivel arm
45
192-22-043
Swivel arm’s bronze gasket
46
192-22-044
Female bearing of arm
47
192-22-047
Wheel of swivel arm
48
192-22-048
Arm of buck
49
302-00-051
Iron’s suspension
50
302-00-049
Stretcher suspension
51
192-22-051
Suspension’s bar
52
192-22-052
Lighting
53
302-22-053
Fluorescent lighting
54
302-22-054
Lighting’s switch
55
192-22-055
Blade of bar support
56
302-22-056
Lighting’s socket
57
302-22-057
Cable of lighting power
58
192-21-055
Plate of lighting
59
302-22-059
Corner of vario
60
302-01-015
Plastic wheel
61
302-22-061
Thermostat knob
62
302-22-020
4-poles corner socket
63
302-22-063
Gland
64
302-00-012
Thermostat of table 110C
65
192-22-065
Base of condenser TS (optional)
66
302-21-024
Relay 12V/DC
67
302-22-067
Ball bearing of stretcher’s suspension
68
302-22-068
Elastic stop
69
192-22-069
Base of heating element

9
L1L2L3
1 2 3 4 5 6 7 8 9
CV M1
TPE
41 42
F52
2.5A
RLE
1 2 3 4 5 6 7 8 910
TM3
TM2 FSM
MB MV2
FS
2.5A
S1 SI SII
K1
A1
135
24 6 A2
LS
TM1 1 2 3 4 5 6 7 8 910
L1L2L3 NN N
PS2
PS1
PS3
12
2
5
36
14
25
LINE 3x220 V-60 Hz
LINE 400 V 3 N 50 Hz
CV
TPE
230 V- MAX 6 A
UVW
Z X Y
UVW
Y
XZ
DC
1 2
3
21
3
PRIMULA
WARNING DIAGRAM
FLEX FL1365
FLEX DOB 1242

10
ELECTRICALL CIRCUIT
Symbol
Articel
Description
RLE
302-22-018
Electronic circuit
FSM
302-03-006
Flap Motor 12V/DC
TPE
302-22-071
Brass terminal block of grounding
PS1
302-22-020
4-poles socket of working surface
PS2
302-03-029
Socket
PS3
302-22-020
4-poles socket of buck
TM1
302-22-072
Power supply terminal block
TM2
302-22-073
Flap motor terminal block
TM3
192-22-008
Button pedal terminal block
CV
302-22-022
302-00-014
Cable of power supply 3Χ1.5mm with plug
Cable of power supply 5Χ1.5mm
LS
302-22-074
Indicator light overheating motor
K1
302-00-010
Relay motor
FS
302-22-075
Circuit safety fuse 2,5 A
F52
302-22-075
PC Board safety fuse 2,5 A
MB
302-00-005
Blowing Button
MV2
302-00-005
Suction Button
SI
308-00-006
Operation ON-OFF switch
SII
302-00-017
Working surface table ON-OFF switch
SII
302-00-017
Buck’s heating operation switch ON-OFF

11
N
N
N
M1
TM1
TPE
PS2
PS1
PS3
L2
FUSE
L3
L1
M3
FUSE
TM
MONO FASE
TRIFASE MOTORE MONOFASE
MOTOR 3FASE
PS3
PS1
PS2
TM1 TPE
CV 230V 50Hz / 110V 60Hz
LINE
M1
13
24
5
6
400V 3 N 50 Hz
LINE
135
64
2
400V 3 N 50Hz
LINE
135
64
2
CV
CV
TPE
PS2
PS1
PS3
U V W
Z X Y
YXZ
WVU
YXZ
U V W
1 2
3
3
21
3
1 2
3
21
3
1 2
PRIMULA
WARNING DIAGRAM
FLEX FL1365
FLEX DOB 1242

12
The machine on which you invested is being manufactured according to International and
European standards by a company, with an experience in the domain of ironing machines,
since 1969.
14 km. Thessaloniki-Kilkis (Liti)
Τel: 2394071245 Fax: [phone]
E-mail: [e-mail]
http: www.primula.gr
Specifications may be subject to change without any prior notice!
TECHNICAL ASSISTANCE
For any advice about the operation of the machine or the spare parts, please contact our agents in
your territory ----------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------------------
-------------------------------------------
or directly us in the below address: