Prince PT2010 User manual
O W N E R ' S M A N U A L
TABLE TENNIS TABLE
MODEL NO.
PT2010
PT2010-00
Escalade® Sports products may be manufactured and/or licensed under the following patents.
6120397, 5816957, 5769744, 5119741, 4911085, 4717157, D460140, D420563, 8414431
Additional patents may be pending. One or more of the listed patents and/or pending patents may cover specific product. 2014 Escalade Sports
USE THIS MANUAL ONLY!
A DIFFERENT MANUAL IS IN THE BOX,
DISCARD THE OTHER.
2
Contact Escalade® Sports customer service department at:
Phone: 1-800-467-1245 Toll – Free !
Fax: 1-866-873-3533 Toll – Free !
E-mail: tabletennis@escaladesports.com
Mailing Address (correspondence only):
Escalade Sports
PO Box 889
Evansville, IN 47706
1. Read this manual carefully before starting assembly. Read each step completely before beginning each step.
2. Some smaller parts may be shipped inside larger parts. Check inside all parts and cartons before assembling or ordering parts.
3. To make assembly easier, use the Hardware Identifier on page 11 to identify and sort all fasteners. Check all cartons for kits. All
hardware may not be located in one kit.
4. Do not tighten hardware until instructed to do so. If hardware is tightened too soon, mounting holes may not align and parts may not
easily fit together. Leave locknuts slightly loose until you are instructed to tighten them.
5. Tools required for assembly: Two 10mm Wrenches, Two 12mm” Wrenches, Two 13mm Wrenches, Crescent Wrench and Channel Lock Plyers.
Note: Adjustable wrenches can be substituted for open end wrenches.
6. Save these instructions and your proof of purchase (receipt) in the event that the manufacturer has to be contacted for replacement
parts.
Please Do Not Return This Product To The Store!
Please visit our Website at:
www.escaladesports.com
ON-LINE TROUBLE SHOOTING TECHNICAL ASSISTANCE
ON-LINE PARTS REQUESTS FREQUENTLY ASKED QUESTIONS
ADDITIONAL ESCALADE®
SPORTS PRODUCT INFORMATION
P R E - A S S E M B L Y T I P S
2014 Escalade Sports
1. If table does not seem level, it is probably due to uneven or un-level floors. Set the table in its PLAYING POSITION and move table several inches
in different directions to find the best location for the table. If the floor is extremely un-level, table may not play or operate properly. If table is high in the
center use adjustable Leg levelers on the outer legs to level the table by turning counter clockwise to raise the table and clockwise to lower.
2. This is an indoor table only! This table must be stored INDOORS to prevent damage to the playing surface. Dampness and extreme temperature
changes can cause the wood to warp, swell, crack or blister. When your table is not in use, it should be folded up in a dry area.
3. Use the locks on wheels to lock table in place. Press down on the wheel lock with your foot to lock, and press on the release to unlock.
P O S T - A S S E M B L Y T I P S
3
1. Attach Caster Wheels (P4 & P5) to T-Legs (P2). Slide a Caster
Wheel with Lock (P4) through upright (P2) and secure it with Cap
Nut (H3) as shown. Tighten Cap Nut with a Crescent Wrench and
use channel locks to hold the Casters in place. On the other end of
the T-Leg attach a Caster Wheel Without Lock (P5). Make sure you
have one Caster Wheel with Lock and one Caster Wheel without
Lock for each T-Leg. Repeat step for second T-Leg.
Caster
with
Lock
Caster
without
Lock
Caster
with
Lock
Caster
without
Lock
P2
3
P4
P5
P5
PARTS REQUIRED:
2 - (P2) T-Leg
2 - (P4) Caster with lock
2 - (P5) Caster without lock
4 - (H3) Cap Nut
TOOLS REQUIRED:
1- Crescent Wrench
1- Channel Lock Plyers
Use Crescent
Wrench here
P4
Use Channel Lock
Plyers here
Make sure these offset holes
are all on the same side of
the assembly as shown.
Note:
P2
4
2. Assemble Cross Tube (P6) to T-Leg assemblies from previous step.
Use Bolts (H7), Washers (H8) and Nuts (H9) but only finger
tighten, these parts will be tightened in the next step. Be sure
that the offset holes in T-Legs match each other and that the
Cross tube (P6) is attached in the two bottom holes of T-Legs.
PARTS REQUIRED:
1 - (P6) Cross Brace
4 - (H7) M8 X 70mm Bolt
4 - (H8) Flat Washer
4 - (H9) M8 Nut
TOOLS REQUIRED:
None
Make sure these offset holes
are all on the same side of
the assembly as shown.
Note:
NOTE:
Be sure to attach the Cross
Tube (P6) to the two bottom
holes in both T-Legs.
Caster
with
Lock
Caster
with
Lock
P6
H7
H8
H9
Finger tighten only. Hardware
will be tightened in a later step.
Note:
5
5. Tighten Cross Tube Nuts and Bolts from previous page at this time.
Detail B
Detail C
3. Place T-Leg Assembly (from previous step) on table top. Be
sure that the offset holes in T-Legs are closest to the
table. See Detail A.
4. Attach T-Leg Assembly to Brackets with Bolt (H10) and Locknut (H11)
as shown in Detail B & Detail C. Tighten the Locknuts (H11) all the
way but be careful not to over tighten as this is a pivot point.
Detail A
T-Leg Shorter hole distance
Closest to the table
NOTE:
PARTS REQUIRED:
1 - (P1) Table Top Assembly
2 - (H10) M6 X 65mm Bolt
2 - (H11) M6 Nut
TOOLS REQUIRED:
2- 10mm Wrench
1- 12mm Wrench
1- 13mm Wrench
H10
H10
H11
H11
Bottom of Table
6
PARTS REQUIRED:
1 - (H12) M8 X 80mm Bolt
1 - (H8) M8 Flat Washer
1 - (H9) M8 Nut
TOOLS REQUIRED:
1- 12mm Wrench
1- 13mm Wrench
H12 H8
H9
6. Insert (H12) Bolt on the T-leg that has the Safety latch
beside it. Bolt must be inserted in the hole closest to the
safety latch, secure bolt with a (H8) Washer and (H9) Nut.
See Detail D & Detail E.
Safety
Latch
Safety
Latch
Install Bolt exactly as shown below,
with the washer and nut on the side
of the Safety Latch.
Note:
Bolt should be sticking out
enough to engage in safety
latch (in later steps).
Note:
Do not insert Bolt
on this side.
Note:
Detail D
Detail E
Correct direction
of Latch Bolt.
Note:
7
TOOLS REQUIRED:
2- 10mm Wrench
PARTS REQUIRED:
2 - (P15) Linkage
2 - (H14) Bushing
2 - (H13) M6 X 90mm Bolt
2 - (H11) M6 Nut
7. Attach Linkages (P15) to T-Legs as shown in Details F &
Details G. Pivot T-Legs up from the table and pivot linkage
(P15) up and align hole in Linkage with hole in T-Leg. Attach
Detail G
Detail F
H13
H13
H14 H11
P15
P15
H14
H11
Linkage (P15) to the inside face of T-Legs using Bolt (H13), Bushing
(H14) and Locknut (H11). Bushing (H14) goes between Linkage and Leg.
Attach other Linkage to T-Leg the same way. Tighten nuts securely but do not
over-tighten this is a pivot point.
Attach Linkage (P15) to the
inside face of T-Legs.
Note:
P15
P15
8
When folding T-Leg assemblies
hold here, away from any
pinch points.
COMPLETE THE REST OF THIS ASSEMBLY.
AT LEAST TWO (2) ADULTS ARE NEEDED TO
WHEN FOLDING LEG ASSEMBLIES DOWN MAKE
SURE TO DISENGAGE THE HINGE FIRST. DO NOT
PUT HANDS ANY PLACE WHERE A PIVOT POINT IS
LOCATED. DO NOT GRASP LEGS, LINKAGE, OR
HINGES. THESE PARTS MOVE AND COULD PINCH
FINGERS OR HANDS CAUSING SERIOUS INJURY.
Note:
Unlock hinge by
pushing down.
8. Unlock the hinge by pushing down as shown and hold the
T-leg in between the two casters. Fold the assembly down
carefully until it rests on the floor.
Note:
9
SET THE TABLE ASSEMBLIES UPRIGHT! WHEN
LIFTING AND ROTATING TABLE, HANDLE TOP
ASSEMBLIES BY GRASPING ONLY THE TOPS
THEMSELVES. DO NOT GRASP METAL LEGS,
CAN MOVE AND COULD PINCH FINGERS OR
HANDS CAUSING SERIOUS INJURY! ROTATE
AT LEAST TWO (2) ADULTS ARE NEEDED TO
WITH T-LEGS FULLY LATCHED.
DO NOT LIFT OR ROTATE TABLE ASSEMBLIES WITH
T-LEGS UNLATCHED. TABLE TOPS ARE HEAVY!
DO NOT ATTEMPT TO ASSEMBLE ALONE!
T-LEGS, LINKAGE , OR HINGES. THESE PARTS
9. With two people raise the table up, until you hear
the Bolt in T-leg engage into Safety Latch. You will
hear a “click” when engaged. See Detail H.
Detail H
You will hear a “click”
when Bolt is engaged in
Safety Latch.
Note:
10
SET THE TABLE ASSEMBLIES UPRIGHT! WHEN
LIFTING AND ROTATING TABLE, HANDLE TOP
ASSEMBLIES BY GRASPING ONLY THE TOPS
THEMSELVES. DO NOT GRASP METAL LEGS,
CAN MOVE AND COULD PINCH FINGERS OR
HANDS CAUSING SERIOUS INJURY! ROTATE
AT LEAST TWO (2) ADULTS ARE NEEDED TO
WITH "T" LEGS FULLY LATCHED.
DO NOT LIFT OR ROTATE TABLE ASSEMBLIES WITH
T-LEGS UNLATCHED. TABLE TOPS ARE HEAVY!
DO NOT ATTEMPT TO ASSEMBLE ALONE!
T-LEGS, LINKAGE , OR HINGES. THESE PARTS
10. With two people and the Latch engaged carefully rotate the table into
the upright position as shown. Pay close attention and do not grasp any
moving parts (Legs, Hinges, Linkages) only grasp the sides of the table as
shown. Repeat Steps 1-10 to assemble second table half.
10
11
11
PT2010-00
Key# Description
Replacement Parts List for Model Number PT2010
2
2
2
4
4
2
4
2
4
2
8
2
2
2
4
8
16
4
4
2
-
2
8
4
4
2
8
10
10
16
24
2
8
8
1
1” Table Top
T-LEG
WELDED LEG ASSEMBLY
LOCKING CASTER WHEEL
NON-LOCKING CASTER WHEEL
CROSS BRACE TUBE
SIDE RAIL
MIDDLE RAIL
CORNER RAIL
RAIL CAP
RUBBER BUMPER
END RAIL
HINGE
SAFETY LATCH
LINKAGE
PLASTIC CORNER
LEG MOUNTING BRACKET
LEG LEVELER
METAL CORNER PLATE
HINGE Mounting Bracket
TABLE TOP SCREW
HINGE BOLT - 3/4”
CASTER CAP NUT
HINGE PLASTIC WASHER
HINGE NUT
3 1/8” BOLT
M8 X 70mm Bolt
FLAT WASHER
M8 NUT
M6 X 65mm BOLT
M6 NUT
M8 X 80MM BOLT
M6 X 90 MM BOLT
PLASTIC BUSHING
This Owner’s Manual
PT2010-P1
PT2010-P2
PT2010-P3
PT2010-P4
PT2010-P5
PT2010-P6
PT2010-P7
PT2010-P8
PT2010-P9
PT2010-P10
PT2010-P11
PT2010-P12
PT2010-P13
PT2010-P14
PT2010-P15
PT2010-P16
PT2010-P17
PT2010-P18
PT2010-P19
PT2010-P20
PT2010-H1
PT2010-H2
PT2010-H3
PT2010-H4
PT2010-H5
PT2010-H6
PT2010-H7
PT2010-H8
PT2010-H9
PT2010-H10
PT2010-H11
PT2010-H12
PT2010-H13
PT2010-H14
PT2010-M1
P1
P2
P3
P4
P5
P6
P7
P8
P9
P10
P11
P12
P13
P14
P15
P16
P17
P18
P19
P20
H1
H2
H3
H4
H5
H6
H7
H8
H9
H10
H11
H12
H13
H14
M1
Part # Qty.
*PARTS IDENTIFIER ON NEXT PAGE.
HARDWARE KIT IDENTIFIER (HARDWARE NOT PRE-ASSEMBLED)
H7 H12 H13 H10 H9
H8
H11
H14
12
P5
H9 H9
P4
H13
H7
H3
P2
H14 H11
P6
H12
H8
H9
P5
H8 H9
P4
H7
H3
P2
H14 H11
P6
H12
H8
H9
U N A S S E M B L E D P A R T S
H11H11
H10H10
13
P R E - A S S E M B L E D P A R T S
H1
H6
H5
H2
P13
H4 Id
P15
P3
H16
P19
P11
P9
H11
H10
P16
H17
P8
P10
P17
P7
P14
H1
H6
H5
H2
P13
H4 H2
P15
P3
H13
P19
P11
P9
H11
H10
P16
H11
P8
P10
P17
P20
P7
P14
H1P1
P21
H5H5
Table of contents
Other Prince Robotics manuals
