
8. Wiring Diagram:
T3M 2.4GLED RGB Controller Manual T3M 2.4GLED RGB Controller Manual
The receivers can be divided into 1~10 zones within effective distance(1pc receiver per zone), no wiring
needed between the receivers.
7. System Diagram:
9. The Charging Methods for Remote Control:
1. When charging, please connect USB cable to the mobile charger or computer with the USB interface.
4. Red indicator light flickers meaning low battery and need to be charged. charging in low battery will affect life of
battery.
3. No memory effect in the lithium battery of remote control. Follow the standard charging procedure even for the first
three times, no need over charge.
2. The blue indicator light flickers while charging, and turns green means the charging is completed. The remote
control can be chargeable even at the OFF state, on which the indicator light is black.
5. The remote should be full charged and stored under low cold drying while a long time without being operated.
And please full recharge every 3 months.
10. Attention:
1. The product shall be installed and serviced by a qualified person.
7. If a fault occurs please return the product to your supplier. Do not attempt to fix this product by yourself.
6. Ensure all wire connections and polarities are correct before applying power to avoid any damages to the LED lights.
5. Please ensure that adequate sized cable is used from the controller to the LED lights to carry the current.
Please also ensure that the cable is secured tightly in the connector.
4. Please check if the output voltage of any LED power supplies used comply with the working voltage of the product.
3. Good heat dissipation will prolong the working life of the controller. Please ensure good ventilation.
2. This product is non-waterproof. Please avoid the sun and rain. When installed outdoors please ensure it is
mounted in a water proof enclosure.
Without Amps With Amps
11. Installation Instructions for the T3-5A (P-C315) Controller (1 or more)
1. Ensure the primary power going to the power supply is turned off or disconnected.
2. Insert the positive (red) and negative (black) wires from the secondary, low voltage side of the power supply into
the positive (DC+) and negative (DC-) terminals on the incoming side of the controller.
3. Insert the positive (gray) wire from the Principal Street Fighter RGB or Principal RGB Light Tape into the positive
(+) terminal on the outgoing side of the controller. Repeat this process by inserting the remaining blue, green and
red wires into the “B”, “G”, and “R” terminals respectively.
4. Each additional power supply in the sign will require an additional T3-5A controller; repeat Steps 1-3 for each one.
5. After connecting all wires, turn primary power on and turn on the controller unit.
6. If using only the T3-5A controller, please see Section 5 for instructions on how to pair and program the T3M remote.
12. Installation Instructions for the T3-5A Controller with PL-GL-CT-B (P-A318) amplifiers
1. Ensure the primary power going to the power supply is turned off or disconnected.
2. When using the P-A318 amplifiers, start by repeating Steps 2-3 outlined in Section 11 for the T3-5A controller and the first power
supply.
3. Using additional RGB wire (cut to the required length), insert the positive wire into the positive (+) terminal on the outgoing side of
the controller. Repeat this process by inserting the remaining blue, green and red wires into the “B”, “G”, and “R” terminals
respectively.
4. On the amplifier, insert the positive (red) and negative (black) wires from the secondary, low voltage side of the power supply into
the positive (DC+) and negative (DC-) terminals on the incoming side of the amplifier.
5. Using the extra RGB wire from the controller, insert the positive wire into the positive (V+) terminal on the incoming side of
the amplifier. Repeat this process by inserting the remaining blue, green and red wires into the “B”, “G”, and “R” terminals
respectively.
6. Insert the positive (gray) wire from the Principal Street Fighter RGB or Principal RGB Light Tape into the positive (+) terminal on
the outgoing side of the controller. Repeat this process by inserting the remaining blue, green and red wires into the “B”, “G”,
and “R” terminals respectively.
7. Repeat Steps 2-6 for each additional amplifier needed.
REV20180920