Pro-Elec PEL01924 User manual

16” Pedestal Fan
Model: PEL01924 & PEL01925

IMPORTANT SAFETY INFORMATION
Please read these instructions carefully before use and retain for future reference.
• When using electrical appliances basic safety precautions should always be
followed.
• Check that the voltage indicated on the rating plate corresponds with that of the
local network before connecting the appliance to the mains power supply.
• This appliance is intended for domestic use only. It should not be used for
commercial purposes.
• This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning the use of
the appliance in a safe way and understands the hazards involved.
• Children shall not play with this appliance.
• Cleaning and maintenance shall not be made by children without supervision.
• There are no user-serviceable parts in this product. Refer servicing to qualied
personnel.
• Do not operate this fan with a damaged plug or cord, after a malfunction or after
being dropped or damaged in any way.
• If the supply cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualied persons in order to avoid a hazard.
• Ensure that the fan is switched off before removing the guard.
• Do not insert anything through the grille when the fan is in use.
• Make sure that the fan is on a stable surface when operating.
• It is recommended to unplug the fan from the mains socket when not in use.
ASSEMBLY
Base
Screws
Motor
Rear guardRear guard
Front guard
Fan blades
Decorative cap
Base
cover
Outer
tube
Fan
retainer
Rear
guard
retainer
Locking
screw
Oscillation
knob
Switch
panel
Height
adjustment
collar
Inner
tube
Base end cap
Locking nut and screw

• Set the base on a level surface and insert the end caps then remove the four
screws.
• Using these four screws, x the stand outer tube to the base and securely tighten
the screws.
• Temporarily remove the height adjustment collar then slide the base cover trim
down the tube to cover the xing with the base. Ret the adjustment collar.
• With the height adjustment collar loosened off, extend part of the inner tube. Re-
tighten the height adjustment collar.
• Loosen the locking screw at the bottom of the switch/motor assembly and insert
the inner tube of the stand into it and push home. Re-tighten the screw.
• Unscrew the rear guard retaining nut from the motor shaft.
• Fit the rear guard onto the body of the fan. Use the two pegs provided to align with
the two holes in the rear guard.
• Lock into position by rmly tightening the rear guard retaining nut.
• Push the fan blades onto the motor shaft aligning the slots. Lock into position by
rmly tightening the retaining ring.
• If not already attached, t the decorative cap to the front guard using the screws
supplied.
• Mount the Front Safety Grill onto the Rear Grill by hanging the top hook clip of
front grille over the top of the Rear Grill. Close the clasps all around the grill, nally
t the nut and screw through the hole in the bottom edge of the front grill and
tighten.
OPERATION
• Connect the mains plug to a suitable outlet.
• Select the desired speed using the speed control:
0 = Device off
1 = Low speed
2 = Medium speed
3 = High speed
• The inclination of the fan head can be adjusted by tilting it forwards and
backwards. The fan head can then be locked into position, which is indicated by
an audible click.
• Oscillation: to make the fan oscillate, push down the oscillation knob. To stop the
fan head from oscillating, pull up the oscillation knob.
• To adjust the height, slacken the height adjustment collar and slide the upper
section to the required height. Re-tighten the height adjustment collar.
CLEANING & STORAGE
• Before cleaning, turn the fan off and unplug from the power supply.
• Use a soft cloth to wipe off any dust. If the fan is very dirty, use a damp cloth and
wipe dry.
• Do not use any chemicals, abrasives or solvents that could damage the fan.
• Store the fan in its original packaging in a ventilated dry area.
• The motor bearings are permanently sealed and do not require additional
lubrication.

INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF ELECTRICAL &
ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical
& Electronic Equipment (WEEE). Any WEEE marked products must not be mixed with
general household waste, but kept separate for the treatment, recovery and recycling of the
materials used. Contact your local authority for details of recycling schemes in your area.
Made in China. PR2 9PP
Man Rev 1.1
TECHNICAL SPECIFICATION
Power consumption 45W
Main voltage 220-240V~ 50Hz
Dimensions (HxWxD) 1250 x 600 x 600mm
Weight 2.3kg