Pro-Elec PEL00500 User manual

1
LED Floodlight with PIR
Models: PEL00500, PEL00501,
PEL00502 & PEL00503

2
Please read these instructions carefully before use and retain for future
reference.
This oodlight must be installed by a qualied electrician in accordance with current
building and IET wiring regulations (BS7671).
IMPORTANT SAFETY INFORMATION
•This product must be connected to Earth.
•The front of this oodlight is made of tempered glass, which cannot be replaced.
Please take care while installing. If it gets damaged, the oodlight must be
replaced and disposed of.
•LED lamps are extremely bright. To avoid possible damage to the eyes, do not
stare into an LED beam.
•In use, avoid touching any external surface of the oodlight, due to the possibility
of high temperatures.
•If the mains cord lead of this oodlight is damaged, it shall be replaced by the
Manufacturer or its service agent, or a similarly qualied person to avoid a hazard.
•The oodlight can be mounted on normally ammable surfaces.
•The oodlight is suitable for use in an ambient temperature between -30°C and
+45°C.
•Terminal block not included. Installation may require advice from a qualied
person.
POSITIONING
•This oodlight is suitable for outdoor lighting applications, for domestic use only.
•Do not use in areas where an explosive or chemical atmosphere may exist. Do not
use in areas where ventilation is restricted.
•It is suitable for mounting on plasterboard, wood or masonry surfaces. Highly
ammable surfaces such as plastic or polystyrene must not be used.
•Do not install on damp or conductive surfaces such as metal. It should be placed
away from any ammable materials.
•Before drilling any xing holes, check that there are no hidden obstructions behind
the mounting surface such as pipes or cables.
•The recommended height for installation of the oodlight is between 0.5 and 3
metres.
•Ensure that there is space around the oodlight to allow adequate circulation of air.
•Orientation of the oodlight is important as shown below:

3
•The oodlight has a beam angle of 120°. It can be tilted at an angle of
approximately 60° and downwards at an angle of approximately 90°.
Note: The angle of adjustment will vary slightly between models.
INSTALLATION
The oodlight is suitable for connection to a 220-240V, 50Hz earthed supply. It is
designed for permanent connection to xed wiring, which must be a suitable circuit
protected by an RCD and an MCB or fuse of the correct rating.
Ensure that the mains supply is isolated before commencing installation.
Before beginning installation, check that you have all the tools you need.
•Check that the oodlights and its mains lead are not damaged. If there is any
damage, return it to the place of purchase. Do not attempt to repair it yourself.
•Choose the location to x the oodlight, taking into account the guidance above.
•Use the oodlight bracket to mark the position on the xing holes.
•Drill the xing holes and x the oodlight into position using the appropriate size
screws and wall plugs (not provided). Check that it is securely xed.
•Connect the main lead from the oodlight to an IP rated junction box. Ensure that
the correct polarities for Live, Earth and Neutral are observed:
- Connect the green/yellow Earth wire to the Earth terminal ‘E’.
- Connect the brown Live wire to the Live terminal ‘L’.
- Connect the blue Neutral wire to the Neutral terminal ‘N’.
•After wiring, check that there are no bare wires, all the wires have been correctly
connected and that the cable restraint has been tightened.
•Before connecting power, perform the electrical tests specied in the current
building and IET wiring regulations to ensure that the installation is safe and that
the wiring has been performed correctly.
•Switch on the electricity to check that the oodlight illuminates. Adjust the angle of
the oodlight so that it illuminates the required area. Tighten the oodlight using
the bolts on the brackets.

4
REMOTE CONTROL
•The distance between two luminaries should be more than 50cm, while there
should be no large metal obstructions in front of the oodlight.
•The default settings are:
Mode: Daylight
Duration time: 5 seconds
Sensitivity: 100%
Mode
Daylight mode: the sensor will work
both in the daytime and at night.
Nightlight mode: the sensor will
work only at night, <50lux.
Photocell mode: the luminary light
on automatically at night, <50lux.
Manual override mode: keep the
light on all of the time.
Off mode.
Duration Time
5/10/30 seconds
1/5/10 minutes
20/30/40 minutes
2/5/7 hours
Detection Range
Max. mode: 5-7 metres
Mid. mode: 3-5 metres
Min. mode: 1-3 metres

5
SPECIFICATION
PEL00284 PEL00285 PEL00286 PEL00287
Input voltage 220-240V,
50Hz
220-240V,
50Hz
220-240V,
50Hz
220-240V,
50Hz
Lumens 680lm 1400lm 2100lm 3500lm
Wattage 10W 20W 30W 50W
Beam angle 120° 120° 120° 120°
Dimmable No No No No
Nominal lifetime
of lamp 30,000h 30,000h 30,000h 30,000h
Number of
switching cycles 15,000 15,000 15,000 15,000
Colour
temperature 6500K 6500K 6500K 6500K
Colour rendering ≥65 ≥65 ≥65 ≥65
Warm up time
(60% full light)
Instant full
light
Instant full
light
Instant full
light
Instant full
light
Sensor PIR motion
sensor
PIR motion
sensor
PIR motion
sensor
PIR motion
sensor
Detection angle 90° 90° 90° 90°
Sensitivity (max) 7m 7m 7m 7m
Installation
height (m) 1.8 - 2.5 1.8 - 2.5 1.8 - 2.5 1.8 - 2.5
Ingress rating IP44 IP44 IP44 IP44
Earthing Class I Class I Class I Class I
Max. projected
area of oodlight
(mm)
130 x 90 180 x 126 210 x 147 260 x 182
Dimensions (mm) 130 x 90 x 34 180 x 126 x
36
210 x 147 x
37
260 x 182 x
41
Weight 0.37kg 0.58kg 0.77kg 1.58kg
INFORMATION ON WASTE DISPOSAL FOR CONSUMERS OF
ELECTRICAL & ELECTRONIC EQUIPMENT.
When this product has reached the end of its life it must be treated as Waste Electrical
& Electronic Equipment (WEEE). Any WEEE marked products must not be mixed with
general household waste, but kept separate for the treatment, recovery and recycling of
the materials used. Contact your local authority for details of recycling schemes in your
area.
Made in China. PR2 9PP
V.1.0
PEL00501 PEL00502 PEL00503
PEL00500