Pro-gard Products LLC. GMM003 User manual

pro-gard.com
800.480.6680
INSTALLATION GUIDE
GMM003
MOTORCYCLE GUNRACK
2014 - CURRENT
RELEASED 07.2019

pro-gard.com
800.480.6680
2
THESE COMPONENTS ARE REQUIRED
TO INSTALL THE PRO-GARD MOTORCYCLE GUN RACK SYSTEM
I. Removing contents saddle bag
A. Remove all items from the right-side saddle bag of the motorcycle.
II. Removing Saddle bag fasteners
A. Remove the OEM fasteners from the saddle bag brackets located at the top inside the saddle bag.
Replace the retaining fasteners located on saddle bag mounting bracket with the retaining fasteners
(94850A158) provided in the hardware kit.
NOTE: Leave rubber bushings installed.
III. Installing the gun rack
A. Orient the gun rack so the that the barrel of the gun is facing toward the rear of the saddle bag. Align
the mounting holes in the gun rack frame with the OEM holes in the saddle bag. Using the supplied
nuts, bolt, and washers attach the gunrack and saddle bag using the OEM mounting points.
B. Secure all fasteners
IV. Wiring the Gun Lock
A. Mount the release button (momentary switch) in a concealed location that can be reached easily by
the ocer, while holding on to the weapon.
B. Connect the red lead of the gun lock to one side of the release button (momentary switch) and the
green wire from the timer. It will be necessary to add appropriate gauge.
C.
Connect a wire lead from the other side of the release button (momentary switch) to the red wire
from the timer and either a switched or un-switched power source on the fuse block. This will allow
the lock to operate with the ignition key on, or o, respectively.
D.
Connect a wire lead from the other side of the release button (momentary switch) to the red wire
from the timer and either a switched or un-switched power source on the fuse block. This will allow
the lock to operate with the ignition key on, or o, respectively.
MOTO - GUN RACK SYSTEM
PARTS LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
MAIN FRAME3G180611
MAGAZINE BRACKET3G180712
CHARGING BRACKET3G1803
1
3
BARREL FOAM BRACKET3G56014
BARREL FOAM3G58615
R GUN LOCKG4904-NPG
16
HARDWARE LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
5/16 SLIP CLIP
94850A15827
5/16-18 x 1" HHMS, Zn (NOT SHOWN )3X7528
1/4-20 X 3/4 PHIL TRUSS HD MS3X0529
1/4-20 WHIZ NUT (NOT SHOWN)3X16410
1/4-20 X 5/8 PHIL TRUSS HD MS3X03211
5/16-18 X 1-1/4 BSHCS, BK
3X197212
1
1
2
2
A A
B B
Products, LLC
7988 Centerpoint Dr., Suite 400
Indianapolis, IN 46256
[phone]
PART DESCRIPTION:
DRAWN BY:
SCALE:
CHECKED BY:
DATE:
APPROVED:
UNLESS OTHERWISE SPECIFIED :
The information contained herein is
proprietary and the property of Pro-gard
Products and may not be reproduced,
disclosed or used for any other purpose othe r
than a quotation to or an order from
Pro-Gard Products without the specific
written authorization of Pro-gard Products .
Computer Path:
SIZE:A
ENGR 1:
ENGR 3:
ENGR 2:
FINAL:
PRODUCTION:
Third
Angle
Projection
DIMENSIONS ARE IN INCHES
TOL ON 3 PLACE DECIMA LS:  .005
DIMENSIONS ARE IN IN CHESTOL ON ANGLES
 1 °
TOL ON 2 PLACE DE CIMAL
 .015
NOTE:
MATERIAL:
FINISH:
STAMP:
ASSEMBLY NO: DRAWING NO:
SHEET:
REV:
APPL:
Pro-gard
1 OF 6
REVISION HISTORY
REV SHEET DESCRIPTION AUTHOR DATE
00 ALL NEW RELEASE EICHHORN 1/28/2015

3
VII. To release the weapon:
A. Grasp the weapon, but do not pull it against the lid of the gun lock.
B. While depressing and holding the release button (momentary switch), push and then pull the weapon
towards the lid of the gun lock to release it from the lock.
Note: One handed operation is possible utilizing the optional 8 second timer. The timer will unlock
the lock for 8 seconds following activation of the momentary switch. If the gun is not pulled
out of the lock within 8 seconds after activation of the momentary switch, the lock will
automatically re-lock.
Important: If lid of the lock does not release, press in on the lid to release tension and reactivate
the release button (unless timer is still active).
PARTS LIST
DESCRIPTIONPART NUMBERQTYITEM
MAIN FRAME3G180611
MAGAZINE BRACKET3G180712
CHARGING HANDLE BRACKE3G180313
BARREL FOAM BRACKET3G56014
BARREL FOAM3G58615
R GUN LOCKG4904-NPG16
HARDWARE LIST
DESCRIPTION
PART NUMBER
QTY
ITEM
5/16 SLIP CLIP3x178-22
7
5/16-18 x 1" HHMS, Zn3X14928
1/4-20 X 3/4 PHIL TRUSS HD MS3X0529
1/4-20 WHIZ NUT3X16
4
10
1/4-20 X 5/8 PHIL TRUSS HD MS3X032
11
5/16-18 X 1-1/4 BSHCS, BK3X197212
1/4 FLAT WASHER, BLACK3X12213
10
7
12
12
9
3
2
6
8
11
4
5
1
13
13