Pro-Ject Audio Systems Tube Box DS2 User manual

INSTRUCTIONS FOR USE
Pro-Ject Tube Box DS2

© Pro-Ject Audio Systems · Pro-Ject Tube Box DS2 · Revision 2016.9.21
2
Dear music lover,
Thank you for purchasing a tube phono preamplifier from Pro-Ject Audio Systems.
In order to achieve maximum performance and reliability you should study these instructions for use carefully.
Warning of a hazard for the user, the unit or possible misuse
Important notice
Safety instructions
AC outlet voltages vary from country to country. Before connecting to the mains, make sure that the
voltage in your area meets the voltage requirements printed on the power supply.
The power supply is used to connect/disconnect the unit from the mains. Make sure that the power
supply is easily accessible at all times. Never handle the device, the power supply while your hands are
wet or damp. Avoid letting liquids enter the device or the power supply. Never place any item
containing liquid, such as a flower vase on or near the device. Never spill any liquid on the devic
e or
the power supply. Never place any naked flame sources, such as lighted candles on or near the device.
The product shall not be used in damp or wet locations, next to a bathtub, sink, swimming pool or any
other similar conditions.
Connectors
Make all connections whilst the phono amplifier is disconnected from the power supply.
Do not connect the phono amplifiers output to a phono input (sometimes labelled
gram
,
disc
or
RIAA
)
on the amplifier.
Never use any other power supply than the one supplied with the unit.
Connecting one or two record players
Connect left and right channels of the tonearm signal lead to the sockets marked
IN1
or
IN2
of the phono
amplifier. The earthing wire may be connected to the screw terminal if you encounter hum problems when
using the record player.
Connection to the amplifier
Connect the output sockets marked
OUT1
or
OUT2
of the phono amplifier to one or two line inputs (such as
AUX
,
CD
,
Tuner
,
Tape
or
Video
) on your amplifier.
Mains power connection
Connect the low voltage plug from the power supply to the
Power 18V DC
socket of the phono amplifier
before connecting the power supply to the mains.
!
!
!

© Pro-Ject Audio Systems · Pro-Ject Tube Box DS2 · Revision 2016.9.21
3
Trigger connection
A unit is equipped with
Trigger Output
and
Trigger Input
sockets (jack 2.5mm, 12V) to turn on/off a Pro-Ject
product with trigger sockets. A 45cm long trigger cable (polarity ) is supplied for this purpose. Longer
cables are available as accessories. The remote power-on signal can be relayed to further units via the
Trigger Output
socket.
Controls
To switch on from standby or to standby
The switch on the left hand side of the front panel turns the unit on or back into standby. The blue LED above
the stand-by switch shows that the unit is switched on. Tube Box DS2 can be used immediately.
Settings
Use the buttons and the rotary control at the front to control the unit. Any change of settings will be
automatically stored for the chosen input, when input is changed or the unit is switched into standby mode.
Input and Output
Tube Box DS2 has two separate inputs and outputs. The button
Input
selects between inputs and the button
Output
switches between outputs.
Subsonic
Turn on and off subsonic filter. Any change will be automatically stored for the chosen input, when input is
changed or the unit is switched into standby mode.
Gain dB
Gain for the outputs can be set from 40dB to 65dB in steps of 5dB or 10dB. Any change will be
automatically stored for the chosen input, when input is changed or the unit is switched into standby mode.
+

© Pro-Ject Audio Systems · Pro-Ject Tube Box DS2 · Revision 2016.9.21
4
Input impedance, variable – low-output MC cartridges
* Input capacitance is irrelevant for low-output MC cartridges
The button
Loading ohm
must be set to
Variable.
Use the rotary controller to set input impedance to desired
value (10Ω-1000Ω)
Input impedance, 47k - high-output MC and MM cartridges
The button
Loading ohm
must be set to 47k.
Input capacitance, variable – high-output MC and MM cartridges
The button Loading pF sets the capacitance to 100pF, 220pF or 320pF
To find out which type your cartridge is, please consult the literature accompanying your cartridge.
The literature for cartridges should also specify the correct input impedance (low-
output MC
cartridges) and the correct input capacitance (high-output MC and MM cartridges), into which the
cartridge is designed to work. If in doubt please consult your dealer.
Examples of typical settings
Ortofon 2M Red
(MM) input gain 40dB,
input capacitance 100pF,
input impedance 47kohms
Ortofon X5-MC
(High-Output MC) input gain 50dB,
input capacitance 320pF,
input impedance 47kohms
Ortofon Rondo Red
(Low-Output MC) input gain 60dB,
input capacitance is irrelevant,
input impedance 10ohms.
Technical specifications Pro-Ject Tube Box DS2
Tubes: 2 x ECC83 (12AX 7A)
Input impedance : variable 10-1000 ohms/ 47.000 ohms (47kΩ)
Input capacitance : 100pF, 220pF, 320pF
Gain: 40, 45, 50, 60 and 65 dB (switchable)
Output voltage typically: 500 mV/1kHz at 5mV/1kHz (at 40dB)
Noise floor: 88 dB (A weighted, at 40dB gain)
THD: <0,04 %
RIAA-equalisation curve accuracy: 20 Hz – 20 kHz / +0,2dB / -0,2dB
Input: 2 pairs RCA/phono sockets
Line-level output: 2 pairs RCA/phono sockets
Outboard power supply: 18 V/1000 mA DC
Power consumption: 490mA DC, <0,5W in standby
Dimension W x D x H (D with sockets) 206mm x 227 (239)mm x 91mm aluminium
240mm x 227 (239)mm x 93mm wood
Trigger output/input: 12V (2,5mm jack)
Weight (without power supply): 1650g aluminium
1930g wood

© Pro-Ject Audio Systems · Pro-Ject Tube Box DS2 · Revision 2016.9.21
5
Potential incorrect use and fault conditions
No signal on one or both channels:
No connection between player and phono amplifier or amplifier. This could be due to a faulty plug,
broken wire or solder joint or simply loose plug/socket connection.
Strong hum:
No earth connection from cartridge or arm, or arm cable to phono amplifier, or earth loop.
Output too quiet or too loud, or distorted:
Input gain incorrectly set - input overloading or insufficiently amplified.
Service
Should you encounter a problem which you are not able to alleviate or identify, please contact your dealer for
further advice. Only if the problem cannot be resolved there, the unit should be sent to the responsible
distributor in your country.
Warranty
The manufacturer accepts no responsibility for damage caused by not adhering to these instructions
for use. Modification or changes to any part of the product by unauthorized persons release the
manufacturer from any liability over and above the lawful rights of the customer.
Copyright, trademarks
Pro-Ject Audio Systems is a registered Trademark of
H. Lichtenegger.
This guide was produced by: Pro-Ject Audio Systems
Copyright ©2016. All rights reserved.
The information was correct at the time of going to
press. The manufacturer reserves the right to make
changes to the technical specification without prior
notice as deemed necessary to uphold the ongoing
process of technical development.