Pro-Ject Audio Systems VT-E BT L User manual

INSTRUCTIONS FOR USE
VT-E BT L

© Pro-Ject Audio Systems · Pro-Ject VT-E BT L · Revision 2016.07.27
2

© Pro-Ject Audio Systems · Pro-Ject VT-E BT L · Revision 2016.07.27
3
Mounting kit for wall mount
VT-E BT L
Controls, features and connections
(1) Power switch
(2) Motor with motor pulley
(3) Platter
(4) Drive belt
(5) Chassis
(6) Screwable record clamp
(7) Tonearm counterweight
(8) Tonearm lift
(9) Tonearm rest and removable transport lock
(10) Tonearm tube
(11) Headshell with finger lift
(12) Ortofon OM 5E cartridge
(13) Feet
(14) Line Output
(15) Phono Output
(16) Grounding screw
(17) Bluetooth module
(18) Rear support
(19) Power supply socket
Universal power supply (not shown) *
Single adapter (not shown)*
Allen key (not shown) *

© Pro-Ject Audio Systems · Pro-Ject VT-E BT L · Revision 2016.07.27
4
Mounting kit for wall mount
(1) The main wall holder
(2) Bottom support 2x
(3) M6 nut 2x
(4) M6 washer 2x
(5) M6 x 35 screw for rear support or main wall holder
(6) Pro-Ject DAMP IT
Packaging overview

© Pro-Ject Audio Systems · Pro-Ject VT-E BT L · Revision 2016.07.27
5
CONTENTS
TURNTABLE and ACCESSORIES overview 2 - 4
MOUNTING KIT and PACKAGING overview 4
SETUP AND INSTALLATION
PART 1 - DESKTOP MOUNT
1. ASSEMBLING THE REAR SUPPORT 7
2. MOUNTING THE PLATTER, DRIVE BELT AND THE RECORD CLAMP 7
3. CARTRIDGE, VERTICAL TRACKING FORCE (VTF) 8
4. CONNECTION TO THE AMPLIFIER
5. BLUETOOTH PAIRING 8
6. MAINS POWER CONNECTION 8
7. SWITCHING ON AND OFF 8
8. CHANGING REPLAY SPEED 9
9. MAINTENANCE AND CLEANING 9
PART 2 - WALL MOUNT
10. DISASSEMBLIMG THE REAR SUPPORT 9
11. ASSEMBLING THE MAIN WALL HOLDER 10
12. ASSEMBLING THE BOTTOM SUPPORT 10
13. MOUNTING ON THE WALL 11
14. MOUNTING THE PLATTER, DRIVE BELT AND RECORD CLAMP 11
TECHNICAL SPECIFICATIONS 12
WARRANTY, SERVICE 12 - 13

© Pro-Ject Audio Systems · Pro-Ject VT-E BT L · Revision 2016.07.27
6
Dear music lover,
Thank you for purchasing a Pro-Ject Audio Systems record player.
In order to achieve maximum performance and reliability, please study these instructions carefully.
Warning of a hazard for the user, the unit or possible misuse
Important notice
During assembling and adjustment small parts could be lost if they are not carefully placed in a suitable
receptacle. Before starting assembly make yourself acquainted with the parts listed above which are
correspondingly numbered in the technical drawings above. Separately packed items are marked with an
asterisk *.
Safety instructions
The power supply is used to connect and disconnect the unit from the mains. Make sure that the plug
is easily accessible at all times. Hold the plug when unplugging the power cord. Never handle the
power cord while your hands are wet or damp.
Avoid letting liquids enter the device. Never place any item containing liquid, like a flower vase, on
or near the device. Never spill any liquid on the device. Never place any naked flame sources, like
lighted candles, on or near the device. The product shall not be used in damp or wet locations, next to
a bathtub, sink, swimming pool or any other similar conditions.
Keep plastic bags away from children to prevent any risk of suffocation.
The turntable was shipped partially disassembled in order to avoid damage to sensitive parts.
Please check immediately to make sure that neither the packaging nor the device was damaged in
transit.

© Pro-Ject Audio Systems · Pro-Ject VT-E BT L · Revision 2016.07.27
7
SETUP AND INSTALLATION
PART 1 – DESKTOP USE
1. ASSEMBLING THE REAR SUPPORT
Remove the rear support panel
(18)
from the packaging and prepare two M6x35 screws for mounting.
Using the screwdriver, carefully tighten the screws to fix the rear support panel on the turntable’s chassis
(5)
as shown in the following illustration.
2. MOUNTING THE PLATTER, DRIVE BELT AND RECORD CLAMP
With the rear support
(18)
mounted and the turntable in vertical position, install the platter
(3)
and the drive
belt
(4)
as shown in following illustration.
After placing the record on the platter, it is necessary to tighten the screw-able record
clamp (6) onto the platter spindle.

© Pro-Ject Audio Systems · Pro-Ject VT-E BT L · Revision 2016.07.27
8
3. CARTRIDGE, VERTICAL TRACKING FORCE (VTF)
The turntable is supplied with fitted cartridge Ortofon OM 5E. The counterweight
(7)
supplied is suitable only
for Ortofon OM cartridges. Cartridge downforce is pre-adjusted from the factory.
Please note: It is not recommended to change the cartridge or vertical tracking force without prior
consultation with your dealer.
4. CONNECTION TO THE AMPLIFIER
The record player has two possible outputs –
Line OUT
(14)
with integrated preamplifier and
Phono OUT (15)
for connection to the preamplifier. If you choose Phono OUT
(15),
than use the
Phono
input (sometimes
labelled gram, disc or RIAA) on your amplifier. Make sure that the phono input offers correct matching and
amplification for the type of cartridge used. If you choose Line OUT
(14),
than use the
Line
inputs (like CD,
Tuner, Tape or Video).
Take care about connecting the left and right channel correctly. The
RIGHT CHANNEL
is usually marked
RED
, the
LEFT CHANNEL BLACK
or
WHITE
. Check the manual of your amplifier for relevant information. An
earthing wire may be connected to the screw terminal between the sockets if you encounter humming
problems.
For detailed product information regarding Pro-Ject Audio Systems interconnect cables, phono amplifiers
and stereo power amplifiers, please visit our website:
www.project-audio.com
5. BLUETOOTH PAIRING
The record player has Bluetooth output and transmit signal automatically when is connected to mains.
It is paired automatically with any device with Bluetooth receiver (such as Pro-Ject MaiA, MaiA DS, Bluetooth Box
s and Bluetooth Box E).
For pairing with other devices and portable speakers use the manual of the given product.
For restart of the Bluetooth transmitter, please disconnect the record player from mains. Restart is needed only
when there is a change of the Bluetooth receiver.
For detailed product information regarding Pro-Ject Audio Systems Bluetooth audio receivers, please visit our
website:
www.project-audio.com
6. MAINS POWER CONNECTION
The turntable is supplied with a power supply suitable for your country's mains supply. Check the label before
connecting to ensure compliance with the mains rating in your house.
Connect the low voltage plug from the power supply to the socket
(19)
on the rear of the record
player before connecting the power supply to the mains.
7. SWITCHING ON AND OFF
Pressing the power switch
(1)
alternately starts or stops the motor.

© Pro-Ject Audio Systems · Pro-Ject VT-E BT L · Revision 2016.07.27
9
8. CHANGING REPLAY SPEED
To play records at
45 r.p.m.
, put the drive belt
(4)
over the larger diameter part of the motor pulley
(2)
. To
revert to
33 r.p.m.
repeat the proceedings using the smaller step on the pulley.
9. MAINTENANCE AND CLEANING
Your record player requires little or no regular maintenance. Remove dust with a slightly moistened antistatic
cloth. Never use a dry cloth because this will create static electricity which attracts even more dust! Antistatic
cleaning fluids are available at specialized stores but must be applied sparingly to avoid damage to rubber
parts. It is recommended to fit the needle cover before cleaning or maintenance to avoid damage.
If the player is not used over a long period of time, the drive belt should be removed to prevent unequal
stretching.
Always disconnect the record player from the mains power supply as a precaution before maintenance!
PART 2 – WALL MOUNT
10. DISASSEMBLING THE REAR SUPPORT
Remove two M6 screws which holds the rear support
(18)
in the back of the turntable.

© Pro-Ject Audio Systems · Pro-Ject VT-E BT L · Revision 2016.07.27
10
11. ASSEMBLING THE MAIN WALL HOLDER
For wall mount it is necessary to mount the main wall holder
(1 – mounting kit)
instead of the rear support
(18)
. For correct mounting, follow instructions from next illustration.
12. ASSEMBLING THE BOTTOM SUPPORT
With the main wall holder mounted on the turntable, unscrew both feet
(13)
from the bottom and instead of
the feet screw the bottom support
(2 – mounting kit)
as shown in the following illustration.
Now the VT-E is ready for mounting on the wall.