Pro's Kit PT-1801 User manual

PT-1801
18V Impact Cordless Drill Driver
User’s Manual
1st Edition,2017
© 2017 Copy Right by Prokit’s Industrial Co., Ltd.

PT-1801 User’s Manual
www.prokits.com.tw 1
Please read this handbook carefully before using the tool
General Safety Rules
WARNING Read all safety warnings and all instructions. Failure to follow
all warnings and instructions may result in electric shock, fire and/or serious
injury.
Save all warnings and instructions for future reference
The term “power tool” in the warnings refers to your battery operated (cordless)
power tool.
1) Work area
a) Keep work area clean and well lit. Cluttered and dark areas invite
accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks
which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a
power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase the risk of electric
shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of
electric shock.
f) If operating a power tools in a damp location is unavoidable, use a
residual current device (RCD) protected supply. Use of an RCD reduces
the risk of electric shock.

PT-1801 User’s Manual
www.prokits.com.tw 2
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication. A moment of
inattention while operating power tools may result in serious personal
injury.
b) Use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, hard hat, or hearing protection
used for appropriate conditions will reduce personal injuries.
c) Avoid accidental starting. Ensure the switch is in the off position before
plugging in. Carrying power tools with your finger on the switch or
energizing power tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result
in personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
f ) Dress properly. Do not wear loose clothing or jewelry. Keep your hair,
clothing and gloves away from moving parts. Loose clothes, jewelry or
long hair can be caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of these
devices can reduce dust related hazards.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at the
rate for which it was designed.
b) Do not use the power tool if the switch does not turn it on and off. Any
power tool that cannot be controlled with the switch is dangerous and
must be repaired.
c) Disconnect the plug from the power source before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool. Power tools are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for misalignment or binding of moving parts,
breakage of parts and any other condition that may affect the power tools
operation. If damaged, have the power tool repaired before use. Many
accidents are caused by poorly maintained power tools.

PT-1801 User’s Manual
www.prokits.com.tw 3
f ) Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in accordance with
these instructions and in the manner intended for the particular type of
power tool, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from intended
could result in a hazardous situation.
5) Battery tool use and care
a) Recharge only with the charger specified by the manufacturer. Acharger
that is suitable for one type of battery pack may create a risk of fire when
used with another battery pack.
b) Use power tools only with specifically designated battery packs. Use of
any other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal objects,
lie paperclips, coins, keys, nails, screws or other small metal objects that
can make a connection from one terminal to another. Shorting the
battery terminals together may cause burns or a fire.
d) Under abusive conditions, liquid may be ejected from the battery; avoid
contact. If contact accidentally occurs, flush with water. If liquid contacts
eyes, additionally seek medical help. Liquid ejected from the battery
may cause irritation or burns.
6) Service
Have your power tool serviced by a qualified repair person using only identical
replacement parts. This will ensure that the safety of the power tool is
maintained.
Special Safety Advice for Cordless Drill
1. Before starting any work on walls, floors or similar, make sure that all power
lines in the work area are switched off at the main switchboard.
2. Inspect the proposed drill holes location for any utility lines (e.g. water, gas,
power) before drilling. Use a suitable device such as a metal or electricity
line detecting device. If in doubt contact a qualified electrician or your utility
provider.
3. Hold power tool by insulated gripping surfaces, when performing an
operation where the screw bits/drill accessory may contact hidden wiring.
Accessory contacting a “live” wire may make exposed metal parts of the
power tool “live” and could give the operator an electric shock.
4. Wear ear protectors when impact drilling. Exposure to noise can cause
hearing loss.
5. Both tools and work-pieces can heat up considerably during the drilling
operation. Allow a sufficient period of cooling before handling. Wear
appropriate gloves.

PT-1801 User’s Manual
www.prokits.com.tw 4
Safety Advice for Rechargeable Battery and Charger
Use only the rechargeable battery from Pro’sKit and the provided charger. Only
plug the battery charger in 230V for PT-1801F/G type and 120V for PT-1801A
type mains. Protect battery and battery charger from humidity. Do not operate
the battery charger outdoors. When it is not in use and before cleaning and
servicing, disconnect the battery charger from the power supply. Take special
care of the battery. Avoid dropping it onto any hard surface and do not subject it
to pressure or any other form of mechanical stress. Keep the battery away from
extreme heat and cold. Do not open or attempt to repair the battery or the battery
charger. If any parts are defective, have them repaired by a qualified technician
or send them to our service department for repair. Only charge the battery at an
ambient (surrounding air) temperature between 10ºC and 40ºC. A charged
battery can be used to power the tool under ambient temperature conditions
between 0ºC and 50ºC.When not in use, store the battery in a dry place between
10ºC and 30ºC.
Important! Danger! Never short-circuit the battery or expose it to moisture.
Do not store it together with any metal parts,which could short-circuit the
contacts. The battery could overheat, start burning or explode.
If any person comes into contact with acid or similar internal fluids or
substances contained in the battery, wash off these substances
immediately with plenty of water. If these substances make contact with
the eyes, rinse with plenty of water and visit a doctor immediately.
Do not place the rechargeable battery into fire or water. It can explode. The
rechargeable battery should not be discarded with domestic refuse, regardless
of whether used or unused. You should return it to a local battery collection point
in accordance with Battery Regulations or return them to us suitably marked
“Used Battery”.
Technical Data
Model
PT-1801A
PT-1801F
PT-1801G
Rated Voltage
18V DC
No-load Speed
Two Gear Speed:
0-350/0~1200 rpm/min
Two Gear Speed:
0-350/0~1200
r/min
Impact / min
0~19200 ipm /min
0~19200 p/min
Range of Drill Bit sizes
Ø 2.0 ~ Ø 13mm
Max. Drilling Capacity
Steel: Ø 8 mm

PT-1801 User’s Manual
www.prokits.com.tw 5
Wood: Ø 20 mm
Concrete : Ø 10 mm
Torque Setting
16 (drive)+1(drill)+1(impact)
Output torque
22/35 N.M
LED Light
YES
Drive
1/2" (13mm) Keyless Chuck
Battery
Model NO.
5PT-1801-BAT
Capacity&
Voltage
18V/1500mAh LI-ion
Charging Time
1 hours
Free Running
time
~40min. (unload speed)
Adaptor
Model No:
5PT-1801-ADA
5PT-1801-ADF
5PT-1801-ADG
Input voltage
120V AC 60Hz
230V AC 50Hz
220V-240V AC
50Hz
Output voltage
18V DC 1.5A
Adapter Plug
A
F
G
Size
230*220*95mm
Weight (including battery)
1.65kg
Accessories
Screwdriver bits
16PCS
Bit size
6pcs drills: Ø 2.0/ 2.5/ 3/ 4/ 5/ 6 mm
1pcs magnetic insert bit holder, Length: 60mm
6pcs: PH1; PH2; PZ1; PZ2; SL 5; SL 6 (L:25mm)
1pcs 6mm Concrete drill bits
1pcs SL6-PH2double end driver bits
Belt Hook

PT-1801 User’s Manual
www.prokits.com.tw 6
Product Features
Operation Instructions
The tool is intended for driving in and loosening screws and drills as well as for
tightening and loosening screws within the respective range of dimensions.
The light of this power tool is intended to illuminate the power tool’s direct
working area and is not suitable for household room illumination.
Insertion and Removal of Rechargeable Battery
Ensuring the correct orientation between the battery and the battery
compartment, insert the rechargeable battery into the power tool. Do not apply
force when inserting the battery. Insertion can be achieved easily and without
resistance. The battery must be inserted completely until the battery retention
clips on the sides of the battery compartment automatically lock it into place. To
remove the battery press the battery retention clips and pull the battery out of its
compartment.
Charging the Battery
The rechargeable battery must be charged before the first use.
The "+" and “- “mark on the battery pack align to the charger "+" and “-“ mark,
insert the battery into the charger and then connect the charger to the mains.
Charging starts automatically. Always disconnect the charger from the mains
Operating trigger
Forward & Reverse switch
Battery Charger
Belt Hook
Torque adjustment
Dual Gear speed
LED light
Battery release
button

PT-1801 User’s Manual
www.prokits.com.tw 7
before you remove the battery from the charger.
When the battery pack is in the charging status, the red light on the left side will
be lit up. The charging time is around 1 ~ 1.5 hours. After the power is full, the
red light will turn off and the green light on the right will turn on. Before removing
the battery from the charger, please remove the charging plug first.
Important! Only use the provided battery charger for charging the battery.
Temperature Dependent Overload Protection
When using as intended for, the tool cannot be overloaded. In case of
excessive loading or when exceeding the allowable battery temperature range
of 0 –50 ° C, the speed is reduced or the tool switches off. In case of reduced
speed,the tool will not run at full speed until after reaching the allowable battery
temperature again. In case of automatic shut-off, switch the tool off, allow the
battery to cool down and then switch the tool on again.
FUEL GAUGE BATTERY PACKS
Battery packs include a fuel gauge which consists of four red LED lights to
indicate the level of charge remaining in the battery pack.
To actuate the fuel gauge, press the “POWER” button, the four LED will light up
to indicate the level of charge left. When the level of charge in the battery is
below the usable limit, the fuel gauge will not light up and the battery will need to
be recharged.

PT-1801 User’s Manual
www.prokits.com.tw 8
Inserting Tool Bits
Important! Always remove the battery before you change the drill or screw bit to
avoid unintentional starting of the tool. With keyless chuck of the cordless drill,
you do not need a key to lock the tool bit in place. Make sure that the drill or
screw bit is not askew when it is inserted and the chuck tightened.
Before inserting drill/screw bits open the jaws of the chuck by holding the lower
ring of the chuck and turn the locking ring counterclockwise. Open the chuck
until you can insert the tool. Insert the drill/screw bit all the way in and then
holding the lower ring, turn the locking ring in a clockwise direction to firmly
tighten it. To remove the tool hold the lower ring of the chuck and turn the
locking ring counterclockwise. Open the chuck until you can remove the tool.
Operating Trigger
Use the operating trigger to start the machine and keep holding it for continuous
operation.
The rotation speed can be varied by depressing the operating trigger. The more
the trigger is depressed, the faster rotation speed. To switch the tool off,
release the operating trigger
Forward and reverse switch
Important! The tool must come to a complete stop before the reverse rotation
lever can be used; otherwise the machine may be damaged.
Use the forward and reverse switch to switch between clockwise (normal) and
counterclockwise rotation or vice-versa. With the forward and reverse switch in
the central position the operating trigger is locked and cannot be depressed. Put
the forward and reverse switch in the central position before you put the machine
down, to avoid unintentional starting.
Torque adjustment
You can control the maximum torque applied to the drill bit with the torque
adjustment knob. There are 16 (drive)+1(drill)+1(impact) position for choice.
Attention! The torque adjustment knob should only be operated when the
tool is not running; otherwise the tool may be damaged.
To set the drill to the lowest available torque setting, twist the torque adjustment
knob until the small arrow on the drill-housing points to the “1” stamped on the
torque adjustment knob. In this position the torque clutch will slip with light
drilling resistance. The higher the number that arrow points to on the torque
adjustment knob, the larger the maximum torque that can be applied before the
torque clutch will slip.
To set the tool to maximum available torque twist the torque adjustment knob
until the arrow points to the drill symbol. In this position, there is no slip in the
torque clutch.

PT-1801 User’s Manual
www.prokits.com.tw 9
Select a lower torque for insertion/removal of screws to avoid damage to the
work-piece (particular wooden work-pieces) or to the screw. For drilling,select a
higher torque setting. Do a test first on an item,which is not your final work-piece,
and adjust the desired torque accordingly before you start the actual work.
Dual Range Gearing
The dual range feature of your drill/driver allows you to shift gears for greater
versatility.
1. Speed 1 (high torque setting), for insertion/removal of screws or drill big
hole use. Slide the gear shifter forward (towards the chuck).
2. Speed 2 (low torque setting), for drill small hole. Slide the gear shifter back
(away from the chuck).
NOTE: Do not change gears when the tool is running. Always keep the drill
complete stop before changing gears. If you are having trouble changing gears,
make sure that the dual range gear shifter is either completely pushed forward
or completely pushed back.
Belt Hook
Practical belt hook for conveniently hanging the power tool on a belt or ladder .The belt
hook will increase your efficiency and make working with the tool a breeze.
Operation for working
Only use tool bits,which can be securely fastened in the chuck and for which the drill has
been designed.
1. Drilling
Check whether the drill bit is correctly inserted and tightly fastened before you
start the tool. Use properly sharpened drill bits. Rotate the torque adjustment
knob to the drill position. Use drill bits that are not overly worn. At the start of
each drilling operation, select a lower speed. For large holes,drill with a smaller
drill bit first and then enlarge the hole using a larger drill bit.
2. Drilling in wood
For drilling in wood, use a wood drill-bit. Protect or fasten the work-piece in a
suitable holder. Mark the positions of the holes to be drilled with a sharp tool or a
nail. Do not apply excessive pressure against the work-piece with the tool.
3. Drilling in metal
For drilling in metal,use a steel drill-bit. Always provide sufficient cooling with
suitable non-inflammable coolants. Protect or fasten the work-piece with a
suitable holder. The work-piece should lie flat on the work bench. Mark the
positions of the holes to be drilled with a center-punch. Do not apply excessive
pressure against the work-piece with the tool. Allow the drill to operate at its

PT-1801 User’s Manual
www.prokits.com.tw 10
normal operating speed.
Important! At the start of drilling,select a lower speed to avoid the bit
slipping away from the desired holes location. If the drill-hole is deep, the drill-bit
may become jammed in the hole. In this event,a high torque could damage the
drill bit or the drill. If the bit becomes jammed, hold the tool firmly and
immediately release the On/Off trigger. Switch to counterclockwise rotation, and
use a low rotation speed to remove the jammed drill bit more easily.
4. Drilling in plastic
For drilling in plastic,use a steel drill and follow the same instructions as for
drilling in wood.
5. Hammer drilling
For drilling in walls, stone, masonry etc. use a masonry-bit. Do not put too much
pressure on the tool; too much force will cause slower drilling speeds
overheating, and a lower drilling rate. Follow the same instructions as for drilling
in metal. When drilling deep holes, if the hammer speed starts to drop off. pull
the bit partially out of the hole with the tool still running to help clear debris from
the hole.
NOTE: Asmooth, even flow of dust from the hole indicates proper drilling rate.
WARNING: Always wear ANSI Z87.1 approved eye protection when performing this.
6. Using the drill as a screw-driver
Before using the tool,check whether the screw-bit is inserted correctly. Avoid
over-tightening screws, otherwise the screw head may be damaged or stripping
of the threads may occur.
7. Screw insertion
Set the rotation direction of the drill to the clockwise direction. Insert the
screw-bit into the slot in the head of the screw. Hold the screw bit perpendicular
to the head of the screw, otherwise the screw or the screw head may be
damaged. Press the screw bit against the screw with a constant pressure while
driving in the screw.
When the screw is completely screwed in, hold the tool firmly and release the
On/Off trigger, otherwise the screw or the screw head may be damaged. If the
On/Off trigger is not released immediately,a high torque could also damage the
drill bit or the drill.
8. Screw removal
Set the rotation direction of the drill to the counterclockwise direction. Insert the
screw-bit into the slot in the head of the screw. Hold the screw-bit perpendicular
to the head of the screw, otherwise the screw or the screw head may be

PT-1801 User’s Manual
www.prokits.com.tw 11
damaged. Press the screw bit against the screw with a constant pressure while
removing the screw.
Maintenance and Cleaning
Attention! Always remove the battery before carrying out any work on
the machine.
To clean, always use a dry or moist, but not wet, towel. Many cleaning agents
contain chemical substances which may cause damage to the plastic parts of
the tool. Therefore, do not use any strong or inflammable cleaners such as
petrol, paint thinner, turpentine or similar cleaning agents.
Always keep air ventilation holes free of dust deposits to prevent overheating.
Service
For more information on PT-1801 series and other products, please visit
www.prokits.com.tw

PT-1801 User’s Manual
www.prokits.com.tw 12
PT-180118V 鋰電衝擊電鑽操作手冊
請在使用工具之前務必細心閱讀操作手冊
一般的安全規則
警告：請詳細閱讀以下所有指示說明，如不遵循下面所有指示，也許會有觸
電及火災等嚴重傷害。請保存本說明書以備將來查閱。以下所有警告中的術語“電
動工具”一詞是指電源驅動(有線)電動工具，或者電池驅動(無線)電動工具。
1) 工作區域
b) 保持工作環境整潔，混亂的環境將帶來事故.
c) 避免在可能發生爆炸的環境下使用電動工具，諸如在易燃的液體周圍，
氣體或者粉塵環境中，電動工具可能製造點燃火花。
d) 使用電動工具時，請使孩子和旁觀者遠離，因為分心可能使你失去對電
動工具的控制
2) 電器安全
a) 電動工具插頭必須匹配電源插座。不要採用任何方式修改插頭。 不要
使用沒有任何接地的電源插座。非修改的插頭和電源插座將減少電擊的
風險。
b) 防止身體接觸接地物表面（如水管、散熱器、冰箱等），如果你的身體
接地，可能有損壞的風險。
c) 避免讓電動螺絲批暴露在雨中或是潮濕的環境中. 雨水滲入電動工具中
會增加觸電的風險。
d) 不要濫用電線：不可直接拉電源線把插頭由插座上拔下，不可提拉電源
線移動充電座，不要讓電源接觸熱源、油和尖銳物或運轉的部件。受損
或纏繞的電線會增加觸電危險。
e) 在戶外操作電動工具時，使用適合戶外使用外接電線，可降低電擊的危
險。
f) 不要在潮濕的地方使用, 若需於潮濕的工作地點使用電動工具, 請使用
帶有電流式漏電斷路器（RCD）裝置的設備, 降低電擊的危險.
3) 個人安全
a) 工作期間，時刻保持清醒意識及並瞭解一般使用常識，不要在過度勞累
時或飲酒及用藥後操作，否則會導致嚴重的人身傷害。
b) 操作時，需使用安全設備，如眼罩.防塵口罩，防滑安全鞋，安全帽，
聽力保護裝置，在適當的條件下使用能減少人身傷害.
c) 避免突然起動。確保接入電源或電池時啟動開關處於關閉狀態，否則可
能導致事故
d) 啟動前務必移除調整電動工具使用的鑰匙或扳手，因其旋轉時可能導致

PT-1801 User’s Manual
www.prokits.com.tw 13
人身傷害.
e) 不要將手伸得過長，使用時保持適當距離與適當的平衡，如此較能控制
意外的情況發生。
f) 穿著適宜，不要穿寬鬆衣服或佩戴首飾。讓您的頭髮，衣服和手套遠離
運轉部件。寬鬆衣服，會有可能會捲入運動部件。
g) 若有提供除塵和集塵的設備，需確保他們連接完好且使用得當。使用這
些裝置可減少粉塵.
4) 電動工具的使用及維護
a) 不要濫用電動工具。正確使用電動工具，會使你工作更有效率，更安全
b) 電動工具的啟動開關若無法開啟或關閉，請勿使用，必須予以修理，否
則會有危險
c) 存放電動工具或更換配件時請移除電源插頭或電池，防止電動工具突然
啟動，造成傷害
d) 電動工具必須貯存在兒童不能接觸的地方。不要讓對電動工具不熟悉或
操作說明不瞭解的人員使用。電動工具在未經訓練的使用者手中是危險
的
e) 維護電動工具：檢查失調或運轉部件，零件破損情況及其它任何可能影
響電動工具操作的情形。如有損壞，電動工具必須修理後才能使用。很
多事故都是因為維護不良造成的。
f) 適當的維護並保持鑽頭（或批頭）鋒利和清潔，會使其不易卡住而更易
於使用
g) 使用電動工具，更換配件及批頭等，必須嚴格根據操作說明及操作方
法，考慮工作環境及需完成的工作。不當的使用會產生危險狀況。
5) 電池的使用及維護
a) 充電時請使用製造商原裝的充電器，不適合的充電器可能會造成火災.
b) 請使用指定的電池包，任何其他電池包的使用可能造成機器損壞和火災
的危險。
c) 當電池組不使用時，避免與其他金屬物體，如迴紋針，硬幣，鑰匙，釘
子，螺絲或其他小金屬物體連接電池端子，引起短路，這樣可能導致灼
傷或引起火災.
d) 在惡劣環境下，電池裡的液體可能會滲出，請勿接觸。如果發生意外接
觸，用清水沖洗。如果眼睛接觸液體，請立即就醫。
6) 服務
本電動工具的維修或更換零件需專業維修人員服務。這將確保電動工具的安全性
關於充電起子的特別安全公告
1.在牆壁、地板或類似物開始任何工作前，請確保工作區域中的所有電源線在主

PT-1801 User’s Manual
www.prokits.com.tw 14
配電板處關閉。
2.當電鑽鑽進牆體內之前，請用金屬探測器檢查一下，避免在鑽取時碰到電源線、
天然氣管道及水管. 如有疑問請聯繫專業電工或您的公用事業供應商。
3.工作時請握住電動工具的絕緣部位，以免當電動工具接觸到隱藏的電線時，金
屬部位會導電，可能造成操作者觸電。
4.使用衝擊鑽時請佩戴護耳罩，暴露於噪音下可能導致聽力損失。
5.當電動工具和部件過熱時，需有充足的時間冷卻後再操作，並佩戴適當的手套。
關於可充電電池的安全公告
只能使用本公司提供的充電電池。PT-1801F/G型插入230V充電器，PT-1801A型
插入120V充電器。保持電池和充電器乾燥。不要將充電器在戶外充電。當不使用
和維修清潔充電器前，請拔掉電源插頭。請特別注意保護電池，避免跌落到任何
堅硬的地面上，不使其受到壓力或任何其他形式的機械應力。電池須遠離極熱和
極冷的環境。不要打開或試圖修復電池或充電器。如果任何部件有缺陷，需由合
格的維修技術人員維修或送我們的服務部維修。充電只能在10℃到40℃之間的環
境溫度下，已充電的電池可以在0℃到50℃環境溫度條件工作。如不使用時，請
將電池儲存在乾燥的環境，溫度在10℃和30℃之間的地方。
重要! 危險! 切勿短路電池或將其置於濕氣中。勿將電池與可能造成短路的
金屬存儲在一起。電池可能發生過熱現象，開始燃燒甚至爆炸.
.
如果任何人接觸到電池內部液體或在電池中類似物質，請立即用水沖洗。如果這
些物質接觸眼睛，請立即用水沖洗，並立即就醫
不要將充電電池放入水中或火中。它可能發生爆炸。可充電電池不能當生活垃圾
丟棄，不論使用或不使用。您應該按照電池回收條例送回到當地電池回收點或交
回給我們並標明“使用過之電池”。
環境保護
廢棄的帶電產品切勿直接扔進垃圾箱，而是回收到政府設立的相應回收
站內。

PT-1801 User’s Manual
www.prokits.com.tw 15
產品規格
型號
PT-1801A
PT-1801F
PT-1801G
額定電壓
18V DC
無負載轉速
0-350/0~1200 rpm/min
0-350/0~1200 r/min
衝擊頻率
0~19200 ipm/min
0~19200 p/min
鑽頭範圍
Ø 2.0 ~ Ø 13mm
最大可鑽範圍
金屬: Ø 8 mm
木頭: Ø 20 mm
水泥 : Ø 10mm
扭力設定
16檔(電批)+ 1(電鑽)+ 1(衝擊槌)
軟/硬扭力
22/35 N.M
LED照明
有
工作夾頭
1/2" (13mm)
電池
型號
5PT-1801-BAT
電池容量
鋰電池 18V 1500mAh
充電時間
1小時
可用時間
40分鐘. (無負載)
適配器
型號
5PT-1801-ADA
5PT-1801-ADF
5PT-1801-ADG
輸入電壓
120V AC 60Hz
230V AC 50Hz
220V-240V AC 50Hz
輸出電壓
18V DC 1.5A
插頭
A
F
G
尺寸（包括電池）
230*220*95mm
重量（包括電池）
1.65kg

PT-1801 User’s Manual
www.prokits.com.tw 16
配件
16PCS
配件規格
6個鑽頭: Ø 2.0/ 2.5/ 3/ 4/ 5/ 6 mm
1個60mm 帶磁延長桿
6個25mm 螺絲披頭: PH1,PH2,PZ1,PZ2,SL5,SL6
1 個6mm 石工衝擊水泥鑽頭配件
1個SL6-PH2 雙頭批頭
1個腰帶夾
產品功能
操作方法
按照規定使用機器
本電動工具適合擰入和擰鬆螺絲。並且可以在木材、金屬、陶器和塑膠上進行鑽
孔。
充電
本產品為鋰離子電池,首次使用請立即進行電池充電。
1. 首先取下電池包，電池包上面的”+”,”-”符號，對準充電座上的”+”,”-”符號方向，
將電池包平直插入充電座到底，再連接充電電源插頭，自動開始充電。(加示意圖)
啟動開關
正反切換開關
扭力杯
充電座
電池釋放按鈕
LED 燈
快慢速切換
腰帶夾

PT-1801 User’s Manual
www.prokits.com.tw 17
2. 電池包在充電狀態時，充電座上左邊的紅燈會亮起，充電時間大約1~1.5小時，
電力充滿之後，紅燈熄滅，右邊的綠燈會亮起，請移除充電電源插頭。(加示意圖)
重要! 僅使用本公司提供的電池充電器。
過長時間充電會對電池造成傷害。
溫控的過載保護裝置
如果按照規定使用電動工具，機器不會過載。但是在強烈負載的狀況下或者蓄電
池的溫度在許可溫度範圍（攝氏0–50度）之外，電動工具會自動關閉。 如果機

PT-1801 User’s Manual
www.prokits.com.tw 18
器以低轉速繼續運作，必須等待蓄電池的溫度恢復到許可的溫度範圍內之后， 電
動工具才能夠再度以最高轉速運轉。 如果機器自動關閉了，先關閉電動工具並等
待蓄電池適度冷卻之后， 再重新啟動電動工具。
電池電量顯示
電池包配有電量顯示功能，由四個紅色LED燈組成，用於指示電池包中剩餘的電
量。請按住”POWER”按鈕，LED燈會亮起指示剩餘電量。當剩餘電量低於可用極
限，則LED燈不會點亮，電池包需要進行充電作業。
安裝批頭、鑽頭
本電動工具具有三爪夾頭，不需要輔助工具就可以拆裝所需的批頭。拆裝前請先
移除電池包，避免誤觸開關造成人員危險。請確保批頭或鑽頭質量完好。逆時針
旋開夾頭後，平直插入批頭或鑽頭，再順時針旋緊夾頭緊固。若要取出批頭或鑽
頭，逆時針旋開夾頭，然後拉出批頭或鑽頭。
啟動開關
壓下啟動開關電鑽即可開始工作，如果保持一直壓下狀態，電鑽可連續工作。若
鬆開啟動開關，電鑽即停止運轉
正反轉切換及鎖定
重要！在電鑽完全停止下，才可以使用正反轉切換開關，否則可能會損壞機器。
使用正反轉切換開關是使電鑽，朝順時針方向或是逆時針方向旋轉。當正反切換
開關置於中間時，電鑽被鎖定，不能旋轉，可避免意外啟動。
扭力及功能檔調節
您可以透過扭力杯，調節旋轉扭力，共有16檔扭力及鑽孔、螺絲、衝擊，3個功
能檔位可供選擇。
設置電鑽最低可用扭力，轉動扭力杯，直到小箭頭指到“1”。箭頭指向的數字越大，
扭力越大，以適應較大扭力場合的應用。
特別注意 ! 扭力杯操作時，只應在機器不運行時操作，否則可能會損壞機器。
機械式選檔
在電鑽靜止時，可以使用快慢速切換開關，調整電鑽轉速。
第I 檔:
低轉速範圍 ; 適合擰轉螺絲，或者鑽大的孔時。
第II 檔:
高轉速範圍；適用於鑽小的孔時。
特別注意 !如果無法把快慢速切換開關推到盡頭，必須握著頭部稍微轉動夾

PT-1801 User’s Manual
www.prokits.com.tw 19
頭，就可以推到定位。
在機器正高轉速運作時，不可調整選檔開關，避免損壞傳動零件。
腰帶夾
使用腰帶夾可以把電動工具掛在腰帶上。不但能夠空出雙手而且電動工具也隨手
可及。
操作使用
請使用合格的批頭產品, 并確認規格符合本產品的裝配尺寸.
1. 鑽孔
檢查是否正確插入鑽頭及是否牢靠，然後再啟動機器。扭力杯請旋轉至 鑽孔
檔，在每個鑽孔作業開始前，請選擇一個較低的速度。對於較大尺寸的鑽孔作業，
可以用一個較小尺寸的鑽頭鑽穿之後，然後再使用較大的鑽頭。
2. 在木頭上鑽孔
在木頭上鑽孔時請使用適合的鑽頭，將工件使用適當的夾具固定牢靠，用鋒利的
工具或釘子對要打孔的位置做好標記。在操作電鑽鑽孔時，請勿過度使用較大的
壓力。
3. 在金屬上鑽孔
在金屬上鑽孔時請使用適合的鑽頭。鑽孔時請一直保持使用冷卻液，並將工件使
用適當的夾具固定牢靠。工件須緊貼平放在工作臺上。使用中心沖對要鑽孔的位
置做好標記。在操作電鑽鑽孔時，請勿過度使用較大的壓力，並保持合適的速度。
重要! 在鑽孔開始時選擇一個較低的速度，以免偏離鑽孔位置。如果孔比較
深，鑽頭可能會卡在孔裡。在這種情況下使用高扭矩，可能會損壞鑽頭或電鑽。
如果鑽頭被卡住，請牢牢握住電鑽，並立即釋放啟動開關，並切換正反轉開關，
使用低轉速反轉取出卡住的鑽頭。
4. 在塑膠上鑽孔
參見在木頭上鑽孔的方法.
5. 帶衝擊鑽孔
在石頭或磚塊上鑽孔時，請使用適合的衝擊鑽頭。扭力檔請旋至 衝擊錘檔，
鑽孔時請一直保持使用冷卻液，並將工件使用適當的夾具固定牢靠，工件須緊貼
平放在工作臺上，使用中心沖對要打孔的位置做好標記. 在操作電鑽鑽孔時，請
使用適當的壓力，過度施力將導致轉速變慢、過熱及較低的鑽孔速率。當鑽較深