Pro2 HDMIFIB User manual

Operating Instructions
1
HDMI Extender over Fiber
Operating Instructions
Dear Customer
Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before
connecting, operating or adjusting this product. Please keep this manual for future reference.
FEATURES
Provides high-resolution image quality.
Plug-and-play operation - no programming or setup required.
Extends 1080p HDMI signals up to 20km over a optic cable.
Optical fiber use rules out any RF interference.
Ethernet Pass-Through.

NOTICE
Our company reserve the right to make changes in the hardware, packaging and any accompanying documentation without prior
written notice.
Compliant HDCP.

Operating Instructions
2
TABLE OF CONTENTS
Specifications
Package Contents
Panel Descriptions
Connecting and Operating
Typical Application
Maintenance
Product Service
Warranty
SPECIFICATIONS
Note1: Specifications are subject to change without notice. Mass and dimensions are approximate.
PACKING CONTENTS
1) Main Unit.Transmitter & Receiver HDMI Extender
2) Power adapter DC 5V 2Ax2PCS
3) IR-TX cable&IR-RX cable
4) Operating Instructions
OperatingTemperature -5 to +35 (+23 to +95 )℃ ℃
StorageTemperature -10 ~70 (+14 to +158 )℃ ℃ ℃
Operating Humidity 10 to 90%RH (No Condensation)
Storage Humidity 5 to 90%RH (No Condensation)
Fiber Module 1310nm signlemodeTransmitter&receiver
Fiber Connector SC Duplex Connector
Transmission Distance 1080P 36bit @60Hz 20Km(Maximum)
Power consumption TX:8watts;RX:8watts((Maximum)
IR wavelength &frequency Wavelength:940nm,frequency 38kHz
Dimension (L×W×H) TX:L154xW99.5xH27mm;RX:L154xW99.5xH27mm
NetWeight Transmitter:410g,Receiver:410g,
LED Indicators Power,Link/Act and Speed

Operating Instructions
3
PANEL DESCRIPTIONS
Transmitter Panel
① Power input port
② Reset button
③ IR-TX port
④ HDMI input
⑤ SC port
⑥ Power,Link/Act and Speed
⑦ Ethernet port
Receiver Panel
① Power input port
② Reset button
③ IR-RX port
④ HDMI Output
⑤ SC port
⑥ Power,Link/Act and Speed
⑦ Ethernet port

Operating Instructions
4
2) Servicing Personnel: Do not attempt to service the unit beyond that described in these operating instructions. Refer all other
servicing to authorized servicing personnel.
with the handheld remote control.It is recommended to affix thereceiver on the display frame /bezel or the display stand.
4) Safety check: After repairs or service, ask the servicer to perform safety checks to confirm that the unit is in proper working
condition.
3) Replacement parts: When parts need replacing ensure the servicer uses parts specified by the manufacturer or parts that
have the same characteristics as the original parts. Unauthorized substitutes may result in fire, electric shock, or other hazards.
5) Connect the IR TX receiving cables into IR TX port on the back panel and affix the emitter onto the source IR windows.
6) Connect IR-RX cable into IR-RX port on the receiver and affix the IR receiver in direct line of site
Clean this unit with a soft, dry cloth. Never use alcohol, paint thinner of benzine to clean this unit.
1) Damage requiring service: The unit should be serviced by qualified service personnel if:
2) Connect Fiber cables to both fiber port of the transmitter and fiber port of the Receiver.
(d)The unit does not operate normally or exhibits a marked change in performance;
1) Connect the HDMI signal sources (Such as DVD, STB etc) to HDMITransmitter.
3) Connect the HDMI output (Such as HD-LCD, HD-DLP) into the Receiver.
(a)The DC power supply cord or AC adaptor has been damaged;
(e)The unit has been dropped or the cabinetdamaged.
(b)Objects or liquids have gotten into the unit;
4) Connect the power supply into Power port.
CONNECTING AND OPERATING
Attention:Insert/Extract cablesgently.
(c)The unit has been exposed to rain;
PRODUCT SERVICE
TYPICAL APPLICATION
MAINTENANCE