Pro2 HDMIIPECOV2 User manual

Operating Instructions
HDMI Extender over Ethernet
Model: HDMIIPECOV2
Operating Instructions
Dear Customer
Thank you for purchasing this product. For optimum performance and safety,
please read these instructions carefully before connecting, operating or adjusting
this product. Please keep this manual for future reference.
FEATURES
Extends 1080p HDMI signals up to 120m over a single UTP Cat5e/6 cable
Support Point-to-Point, Point-to-Many and Many-to-Many network
configuration
HDCP compliant
Can be cascaded for many layers by adding 10G more Ethernet switches
With wideband IR (38-56kHz) control to the source
Support TCP/IP protocol
With mounting ears
NOTICE
Our company reserves the right to make changes in the hardware, packaging and
any accompanying documentation without prior written notice.
1

Operating Instructions
TABLE OF CONTENTS
Specifications
Package Contents
Panel Descriptions
Connecting and Operating
Typical Application
Maintenance
Product Service
Warranty
SPECIFICATIONS
Note1: Specifications are subject to change without notice. Mass and dimensions
are approximate.
Note2: one TX to many RX or many TX connect to many RX, IP and MAC address
must be different.
PACKING CONTENTS
1) Main Unit. Transmitter & Receiver
2) Power adapter DC 5V/1A x2 PCS
3) IR-TX cable & IR-RX cable
4) Operating Instructions
2
Operating Temperature Range -5 to +35℃(+23 to +95℉)
Operating Humidity Range 5 to 90%RH (No Condensation)
Input Video Signal 0.5-1.0 Volts P-P
Input DDC Signal 5 volts p-p(TTL)
Support Video Format DTV/HDTV:480i/576i/480P/576P/720P/1080i/1080P
Video Output HDMI
Transmission Distance 1080P 8-bit 120m(Maximum) over single CAT5E/6 /24AWG/Solid
Power consumption TX:3watts; RX:3watts((Maximum)
IR Frequency 38kHz-56kHz
Dimension (L×W×H) 103.5x93.5x24.6mm
Net Weight Receiver:220g,Transmitter:220g
TX Default IP address:192.168.168.55
MAC address:00:0b:78:00:60:01
RX Default IP address:192.168.168.56
MAC address:00:0b:78:00:60:02

Operating Instructions
PANEL DESCRIPTIONS
Transmitter Panel
①Indicator of power input
②Status of signal connection
③HDMI input
④Ethernet port
⑤IR-TX port
⑥Reset button
⑦Power input port
3

Operating Instructions
Receiver Panel
①Indicator of power input
②Status of signal connection
③HDMI output
④Ethernet port
⑤IR-RX port
⑥Reset button
⑦Power input port
4
Operating Instructions

Operating Instructions
Setup HDMI TX and HDMI RX
A HTTP server is embedded in each TX and RX. you can setup IP address for HDMI
extender via web browser.
The default IP address of the TX is 192.168.168.55, MAC address is:
00:0b:78:00:60:01.
The default IP address of the RX is 192.168.168.56, MAC address is:
00:0b:78:00:60:02.
Step 1: Assign the PC (or laptop) IP address on the computer : “Control Panel”→”
Network Connections”→“Local Area Connections
Status”→“Properties”→“Internet Protocol (TCP/IP)”, Type the IP address field
with 192.168.168.11 (0-255) and Subnet mask with 255.255.255.0. After that
press OK to save the configuration.
Note: The IP address of PC should be different from the IP address of TX and
RX.
Step 2: Use an Ethernet Cable to connect the PC (or laptop) and the extender. the
power LED for the extender is red and the status LED becomes green.
Step 3: please Ping the connected device through the sequence on computer:
“Start”→ “Run”→ input “CMD”→ input “ping 192.168.168.55” for TX or input
“ping 192.168.168.56” for RX, you will receive the reply if the connection is
established.
Step 4: Login in IE :192.168.168.55 (default IP for TX) or 192.168.168.56(default IP
for RX), You can setup IP address, subnet mask, gateway, and MAC address for
the TX and RX.
Please set IP address for each TX and each RX, IP:192.168.168.XX (XX:1-255.
all IP address for TX and RX must be different .
Please set MAC address for TX and RX, MAC:00:0b:78:XX:XX-XX (XX:01-FF),
The MAC address for each TX and each RX must be different .
Step 5: After click “Apply” button, the green LED light on the device will go out, you
have successfully set IP address for TX and RX now.
Note: if you need to restore the device to it’s factory default settings, please power
on the device, the red light becomes lighting, waiting about 10 seconds, the green
LED light starts working, at this time to press the reset button about 5-10 seconds,
then the green light will go out, you have successfully restored IP address to factory
IP address now.
8
Operating Instructions
CONNECTING AND OPERATING
1) Connect the HDMI signal source (Such as DVD, STB etc) to HDMI Transmitter.
2) Connect CAT5e or 6 cables to both the Ethernet of the transmitter and Ethernet
port of the Receiver. (The cables must follow the standard of EIA-TIA 568B).
3) Connect the HDMI display (Such as HD-LCD, HD-DLP) into the Receiver.
4) Connect the power supply into Power port.
5) Connect the IR TX cable into IR TX port on the back panel and affix the emitter
onto the source IR windows.
6) Connect IR-RX cable into IR-RX port on the receiver and affix the IR receiver in
direct line of site with the handheld remote control. It is recommended to affix the
receiver on the display frame /bezel or the display stand.
Attention: Insert/Extract cables gently.
TYPICAL APPLICATION
1) One to One
5

Operating Instructions
2). One to many
Connect HDMI Transmitter port and Receiver ports to the Ethernet
Switch
6
Operating Instructions
3). Many to many
A HTTP server is embedded in TX and RX, you can setup IP address for
RX via web browser. Please refer to "Setup HDMI TX and RX" in page 8.
7