PROAIM Kit-6-CF User manual

DSLR Filmmaking Kit
(Kit-6-CF)
INSTRUCTION MANUAL
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any
means, electronic, mechanical, photocopying, recording, or otherwise, except as may be expressly permied
by the applicable copyright statutes or in wring by the publisher.

PROAIM DSLR FILM MAKING KIT 6-CF 2
INTRODUCTION
PROAIM DSLR Kit 6-CF is full producon ready lmmaking equipment for prosumer operators to
increase the quality and eciency during producon. This shoulder mount camera rig is a
dynamic piece of equipment that moves with the operator in a wedding shoot, corporate
communicaons, and POP producon to produce 'slls' and videos alike. It consists of versale
camera cage, durable mae box and precise follow focus that are highly congurable and
adaptable to the daily demands of producon. It embraces the exibility to accessorize and
match producon requirements for professional results.
IN THE BOX
Please inspect the contents of your shipped package to ensure you have received all that is
pictured and listed below.
Cage brackets
4x 200mm female rods
PRO Zoom
Counter weight
Straight bracket
Rod Support System
2x 300mm female rods
Shoulder pad
Handle Set
Top Handle
Gear Ring Belt
Speed Crank
Shim Set
X9 Follow Focus
2x 150mm male rods
Mic-suspension
15mm adapter
Accessories
Matte Box MB-600
weight brackets
Shoulder Rig Support Rod

PROAIM DSLR FILM MAKING KIT 6-CF 3
ASSEMBLING YOUR MB-600 MATTE BOX
 Insert the French ag (top) to your mae box as shown below and then ghten the knob.
 Insert the Side ag to your mae box as
shown below and then ghten the knob as
shown below.
 Wrap the knicker on conversion ring, as
shown in the image

PROAIM DSLR FILM MAKING KIT 6-CF 4
 Aach rod support system to your tripod plate and ghten with screw driver. Then mount
the setup onto your tripod and secure with provided knob.
 Loosening the knob and simple push of provided buon on quick release adapter allows
you to remove quick release plate. Now aach it to camera base and ghten to secure.
Assembling Your DSLR Filmmaking Kit 6-CF
 Slide in the camera setup onto quick release adapter, reghten the knob to ensure slip free
connecon.

PROAIM DSLR FILM MAKING KIT 6-CF 5
 Loosen the knob on cage bracket in order to insert it to 450mm rails. Using same approach
insert another bracket to front of rails and ghten to secure.
 Now insert 2x 300mm female rods into quick release adapter. Now aach 2x 150mm
extension rods to rails and ghten the knobs.
 Loosen the knobs on top of cage brackets in order to insert 2x200mm rods into them,
reghten to secure.

PROAIM DSLR FILM MAKING KIT 6-CF 6
 Aach top handle to 200mm rods at cage top, reghten the knob to ensure slip free
connecon.
 Aach straight bracket to back of rail system and ghten the knob. Then insert 2x200mm
rods into it and secure with provided knob.
 Now insert shoulder pad to 200mm rails, also aach counter weight and secure with
provided knob.

PROAIM DSLR FILM MAKING KIT 6-CF 7
 Aach exible gear ring to your camera lens and ghten the screw.
 Now insert X9 follow focus to front of rail system, adjust follow focus with your camera and
secure.
 You can also aach speed crank to fol-
low focus as per your requirement.

PROAIM DSLR FILM MAKING KIT 6-CF 8
 Now insert MB-600 mae box to front rails, align with lens and secure with the knob as
shown below.
 Aach handle setup to front of rods and ghten the knobs to secure it.
NOTE: You can lt handle set as per your requirement by loosen the knob.

PROAIM DSLR FILM MAKING KIT 6-CF 9
(SHOWN WITH OPTIONAL ACCESSORIES)
Note: If you wish to use your setup with shoulder rig support rod then please use following
sequence of text and pictures to assemble your kit.
A S S E M B L I N G Y O U R S H O U L D E R R I G S U P P O R T R O D
 Wear your belt around your waist and secure with the help of velcro as shown below.
YOUR PROAIM DSLR FILMMAKING KIT 6-CF
ALL DRESSED UP AND READY TO GO

PROAIM DSLR FILM MAKING KIT 6-CF 10
 Aach rod support to waist belt properly. You can adjust the height of your rod support
with the help of provided knobs.
YOUR DSLR FILMMAKING KIT 6-CF WITH ROD SUPPORT
ALL DRESSED UP AND READY TO GO
(SHOWN WITH OPTIONAL ACCESSORIES)
 Aach the rod support to your shoulder rig via 15mm rod adapter .This set up allows you to
have fague free and long comfy shoots.

PROAIM DSLR FILM MAKING KIT 6-CF 11
WARRANTY
We oer a one year warranty for our products from the date of purchase.
We will repair or replace your product, free of charge, in the event of a defect in materials or
crasmanship obtained during normal use or handling based on the user manual. Please note
that we will not cover any shipping costs for returning the product to us. If any VAT or import
dues are applied to the return, we will also charge these costs to the customer.
The warranty does not include, by the way of example, damage caused by products that we do
not supply or from mishandling in transit, accident, misuse, neglect, lack of care of the product ,
or service by anyone other than our company.
We are not liable for incidental or consequenal damages resulng from the use of the unit or
occurring due to any breach of this warranty.
Replacement parts of the product will be provided at nominal cost (covering the cost price of the
replacement parts only) to the customers aer the Warranty Period has expired. We will cover
the complete cost of sending replacement parts within the warranty period. Aer that, Nominal
cost of the product & Actual shipping cost will be charged.
Do not send the unit to us without rst geng a response and geng the approval to send back
the item.
In case of any kind of dissasfacon, we urge you to Contact us immediately and we shall do our
best to help you out.
For any other assistance you can reach us via email.