PROAIM Victor Pro CT-VCTR-PRO-32 User manual

1
Please inspect the contents of your shipped package to ensure you have received everything that is listed
below.
Victor Pro Video Producon Camera Cart (CT-VCTR-PRO-32)
Assembly Manual
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
What’s In The Box
Lower Shelf
2 x Crossbars
2 x Hinge Handle
Allen key L–Type (Size 4mm)
4 x Screws
Top Shelf
Carrying Handle
4 x Knobs

2
2 x Pneumac Tires Without
Break With Packing Pouch
2 x Pneumac Tires With
Break With Packing Pouch
Victor Pro Camera Cart Setup
• Unlock the er (With break) by ipping the
given knob.
4 x (31” Length) Rods With Packing
• Aer unlocking, separate the top and lower
shelf apart.
• Pull and ip the locking pin from downward
to upward direcon to open locks.
NOTE: Two peoples are needed to assemble the cart.
Pneumac Tires With break
v
v
• Firstly, open all 4 locks present on each side
of the cart.

3
• The cart would look like this aer aaching
both the res (With break).
• Unlock the er (non break) by ipping the
knob.
• Aach the unlocked res (non break) on
lower shelf’s dovetail bracket by sliding as
shown in image.
Pneumac Tires Without Break
Released Break
NOTE: To keep the cart in stac posion, lock
the wheels by pushing down the lever.
• Secure the re using the knob.
• Aach the unlocked re (with break) with
lower shelf’s dovetail bracket by sliding it, as
shown in the image.

4
• The cart would look like this aer aaching
both the res (non break).
• Loose all the 4 knobs of lower shelf’s corner
hole and insert rod into it, as shown in image.
Rod Assembly
Carrying Handle
• Now, ghten all the knobs to ensure proper
aachment of all the rods.
• Loosen al the screw of the carrying handle
using the Allen key (L-type), as shown in the
image.
• Follow the same step for removing all the
screws before aaching the carrying handle.
• Now place the carrying handle at the back of
the boom shelf.

5
• Follow same steps for all screws.
Top Shelf setup
Crossbar Assembly
• Now, place the clamps of the crossbar on the
rods, as shown in the image.
• Loosen the knob to open the clamp of cross-
bar.
• Tighten all the knobs of the upper shelf to
properly secure it.
• Now, align and mount the upper shelf on top
of the rods.
• Now, properly screw the carrying handle
using the Allen key.

6
• Press Both the buons to open ap.
• The crossbar would look like this aer
securing with clamps.
Hinge Handle
• Tighten the knobs of the crossbar to securely
posion it.
• Loosen the handle of the hinge handle to
open its clamp.
• Place the handle clamp on the rod and adjust
the hinge handle accordingly.
• Follow the same step to aach the second
hinge handle.
NOTE: It creates leverage of liing the cart over
obstacles, stairs or other incline surfaces.

7
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon and
evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our utmost
support and care unl you use our product.
YOUR PROAIM VICTOR PRO VIDEO PRODUCTION CAMERA CART
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)