Furniture Solutions 11TOC3S User manual

Imported by Furniture Solutions (Aust) Pty Ltd New South Wales, Australia.
For any assistance with assembly or for missing parts please contact:
Place of purchase or Furniture Solutions on below
Customer Service (Australia) Phone-1300 794 188
Email- [e-mail]
INSTRUCTION MANUAL
TOCOA 3 SEAT SOFA-BED
ITEM CODE: 11TOC3S
111TOC3S
Imported by Furniture Solutions (Aust) Pty Ltd
10-16 Daisy St,
Revesby, NSW. 2212
www.furnituresolutions.com.au

PRE-ASSEMBLY PREPARATION
Before you start:
1. Choose a clean, level, spacious assembly area. Avoid hard surfaces that may damage
the product
2. Take care when lifting. Product should be assembled as near as possible to the point of
use
3. Ensure that you have all required contents for complete assembly
4. Always read the assembly instructions carefully before beginning assembly.
5. Keep all hardware parts and packaging out of reach of small children.
6. Do not over tighten the screws and bolts as this may damage the threads
211TOC3S
20
MINUTES
ALLOW TIME PEOPLE REQUIRED
X2
Special Notice: Parts carton is located in zipper pocket in base
in sofa.

PARTS LIST
PART QTY CODE IMAGE
1 STEEL LEG 4 P230511-3L
2 BOLT: M6 x25mm 16 P230511-3BM625
3 WASHER: M6 16 P230511-3WM6
4 NUT: M6 16 P230511-3NM6
5 SPANNER: M6 1 P230511-3SM6
6 TOOL: 4MM 1 P230511-3T4MM
311TOC3S

411TOC3S
ASSEMBLY INSTRUCTIONS
Please prepare work area as instructed in page 2:
As indicated in diagram below lay front of sofa face down.
You will see a zipper in dust cover, inside you will find a box containing legs
and hardware pack. Once all items are checked against list on previous page,
we can begin to fit legs to metal base. Note legs are angled when fitting
please ensure angle is facing away from sofa. Now take steel leg [1] and aline
holes in plate of leg and plate located in corner of frame, once aligned take
bolt [2] and from underneath insert thru holes, so that open threaded end is
facing upwards. Next add washer [3] by sliding over bolt end. Next take nut
[4] and by hand seat thread correctly on bolt. Note you will notice that one
side of the nut has a coloured nylon ring, that ring should be facing up. Next
take tool [5] and insert into head of bolt from underneath, push up till head of
bolt is flat against frame, then take spanner [4] and tighten nut till flat against
frame. Repeat for all bols and other legs. Assembly complete. With the help
on another person lift and roll complete sofa towards end with legs closest to
edge of sofa until can place on feet. Before use please consult operating
instruction

511TOC3S
INSTRUCTIONS-OPERATING OF FUNCTIONS
About CLICK CLACK mechanism:
The ratchet system used is designed only to work one way, whenever back or
arms mechanism is in a position other than flat to change position you will
need to unlock ratchet. To unlock you will be required to gently push back/arm
fully forward till you hear a clack sound, then you can lower back/arm to go
flat.
Click Clack has a 3 stage mechanism which uses a ratchets system.
First position is flat for use as a bed. This model has added armrest function.
Second position is Lounger when back is mid way up in locked position.
Third position is as a Sofa full upright locked position.
Please view Images of positions available and move to next page for written
instruction.

611TOC3S
INSTRUCTIONS-OPERATING OF FUNCTIONS
Instruction start from fully flat position:
Starting from flat position to move to Lounger position.
With a person on each side of sofa, in unison lift backrest up till you hear a
click noise, this should then hold mid way lock.
To go from Lounger position to Sofa position.
With a person on each side of sofa, in unison lift backrest till you hear another
click, again this should then hold at upright position.
To go back to flat or Bed position, you will need to release locking mechanism.
This done by lifting and pushing backrest forward till you here clack.
Once you here the clack lower backrest till flat.
Armrest & split back functions operate the same as above.
Note/Warning:
The ratchet mechanism is designed only to work one way you can only lock the
2 upright positions from flat starting.
So can not go from Sofa position to Lounger position must always go back to
flat position.
If for some reason you do not get a lock position when raising from flat
position.
Lift backrest all the way to the clack release point then back again, sometimes
doing it twice has better success.

711TOC3S
CARE AND MAINTENANCE
Varieties of materials are used in construction of “Click Clack sofa” furniture range, Such as
Stainless Steel; Chrome plated steel: Powder coated steel, Timber, PU synthetic fabric & a
variety fabric. All will require some form of maintenance to extend the life of finishes and
general appearance.
Please see below instruction unique to your chosen model.
Tocoa Click Clack Sofa-bed
Covering : Polyester Fabric / PU Synthetic
Frame : Polished Steel
Legs : Polished Steel
Polyester Fabric;
Vacuum regularly with a soft brush attachment to remove dust and grit, & or wipe with a
soft colourfast cloth dampened with plain water. This should be done as often as necessary
or at least every 2 weeks. Do not rub excessively. Special note salts and body oils which
occur naturally in human skin can build up in fabric, please consider having a professional
clean done depending on use once a year. In areas of high humidity more frequent cleaning
will be required.
PU Synthetic;
Vacuum & or brush away dust & grit as necessary, wipe with a soft clean dye fast cloth.
Every 3-4 months remove excess body oils with a soft, clean dye fast cloth & appropriate
cleaner for synthetic fabrics. Follow direction as recommended.
Frequency of periodic care depends on usage.
Notes:
Accumulation of perspiration and body oils on arm pads, headrest etc. may damage your PU.
These areas and will require more frequent cleaning.
PU is not resistant to animals. Claws scratch covering, saliva is acidic and can damage PU
finish.
Alcohol, hair spray, gel mousse, perfume, deodorants, some medication and dye
penetration from cloths can have adverse effects on surface of PU.
Do Not on fabric or PU;
Expose direct to sunlight, intense heat, weather and soak unnecessarily.
Always avoid excessive hard rubbing.
Do not use saddle soap, detergents, solvents, abrasives, unidentified cleaners, or any
product containing silicon or solvent. Do not dry clean or machine wash.
Polished Steel;
For best results use microfiber cloth or moist clean cloth. Ensure not to leave
damp.

811TOC3S
SAFETY WARNINGS AND ADVICE
Notices and Advice
Please be advised that products are limited in design for residential use only and are not
suitable for commercial use.
Please be advised that materials used in your furniture are not impervious to neglect, acts of
god, abuse, alcohol spills, improper use of chemicals such as bleach or any solvent based
products.
Please be advised that heat sources such as direct sunlight, log fires, heaters and air
conditioners can have adverse affects on your furniture.
Please be advised that fitting, bolts, nuts and or screws should be checked periodically to
ensure they have not loosened over time. Remember do not overtighten.
DO NOT
•Place in direct sunlight.
•Place in close proximity to open flame or heaters.
•Place in direct line of air conditioning ducting.
•Leave spills or food on sofa clean off immediately
•Pull loose thread, cut them instead.
Safety warnings
•DO NOT:
•drop, drag always with the help of another person lift and place, to avoid damage to floor
surface & or legs of sofa.
•Sit on arms or back when upright, this could damage internal mechanism.
•Fold mechanism with linen or cushions on sofa.
•Pull loose thread, cut them instead.
•Jump, flop or stand on sofa.
•When using as a bed sit first then reline into sleep position

911TOC3S
WARRANTY DETAIL
1 Year Warranty
A one (1) year warranty applies to product against any defect associated with faulty
workmanship for a period of (1) year from date of purchase.
Furniture Solutions accepts no responsibility for defects caused by incorrect assembly,
mishandling, acts of god, general wear & tear including fading, creasing of covering, aging of
foam and fibre filling IE Height reduce over time, stains from spills, chipping/scratching,
exposure to extreme heat/cold, mould/mildew, hardware corrosion, misuse of the products
& defects caused by failure in duty of care for the product in accordance with the care
instructions. Warranty is based on normal household use and not for commercial use.
Warranty only extends to original purchaser and is not transferable, except when given as a
gift.
Notice:
While every effort is made to use quality materials our products are limited in design for
domestic use only & are not suitable for commercial use.
Care should be taken not to place product near heat sources.
Duty of care:
While every attempt is made to supply product using quality components there is always a
need from consumer to help ensure long life of use for product. Instruction manuals are
designed with the nature of materials used in construction of the product.
*Proper use of item only what it is designed to do
*Regular maintenance and cleaning
In areas of high content of salt air, pollution & moisture require more frequent cleaning.
Claim management:
To make a warranty claim, customers can either contact the retailer where the purchase was
made or Furniture Solutions on contact details below. Proof of purchase will be required
before proceeding with any claim. In the case of product defects providing photos may be
able to speed up processing of the claim. If missing parts please refer to assembly
instructions for identification of said part and contact either of the above.
“Our goods come with guarantees that cannot be excluded under the Australian Consumer
Law. You are entitled to a replacement or refund for a major failure and for compensation
for any other reasonably foreseeable loss or damage. You are also entitled to have the goods
repaired or replaced if the goods fail to be of acceptable quality and the failure does not
amount to a major failure”.