Sauder County Line 427719 User manual

sauder.com
NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE STORE.
sauder.com
CONTACT US FIRST
BEFORE MAKING ANY RETURNS TO THE RETAILER.
Visit sauder.com/service to order replacement parts, view video assembly tips, or chat with a live rep.
Prefer the phone? Give us a ring at 1-800-523-3987.
Customer Service is available Monday-Friday - 9 a.m. to 5:30 p.m. EST (except holidays)
Sauder.com
Share your journey! Lot # 553194 10/02/20
Purchased: __________________
Enlish p 1-24
Français p 25-28
Español p 29-32
Lateral File
County Line Collection | Model 427719
Get all organized
and stu.

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
No. 2 Phillips Screwdriver
Tip Shown Actual Size
Hammer
Not actual size
3
4
5
6-24
25-28
29-32
33-34
35
427719 www.sauder.com/servicePae 2
Scissors
Tape Measure

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
D32 LEFT DRAWER SIDE (2)
D33 RIGHT DRAWER SIDE (2)
D61 DRAWER BACK (2)
D729 DRAWER BOTTOM (2)
E BOTTOM MOLDING (1)
F LEFT FRONT LEG (1)
G RIGHT FRONT LEG (1)
H LEFT REAR LEG (1)
J RIGHT REAR LEG (1)
K BACK (2)
L DRAWER FRONT (2)
M63
DRAWER BRACE (2)
(Hidden part usin recycled
material. Color may vary.)
427719www.sauder.com/service Pae 3
A
B
C
D
E
F
G
H
J
K
L
D33
D729
M63
K
D61
D32

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
427719 www.sauder.com/servicePae 4
(EXTENSION SET SHOWN SEPARATED)
EXTENSION
SLIDE - 4
45MC
EXTENSION
RAIL - 4
45MA FILE BAR - 4
1B FILE ROD - 4
9B FILE BRACKET - 4
12B
FILE GLIDE - 4
19B HIDDEN
CAM - 22
1F 7F TWIST-LOCK®
FASTENER - 8
WOOD
DOWEL - 6
15F
DRAWER FRONT
BRACKET - 4
10G 20G DRAWER
STOP - 2
INTERLOCK
TRACK - 1
22G 29G SAFETY
STOP - 2 WASHER - 4
10I PULL - 2 98K
BLACK 9/16" LARGE HEAD SCREW - 8
1S 3S GOLD 5/16" FLAT HEAD SCREW - 16
BROWN 7/16" LARGE HEAD SCREW - 8
6S 30S BLACK 1-9/16" FLAT HEAD SCREW - 10
SILVER 1/4" MACHINE SCREW - 4
61S
CAM
SCREW - 22
8F

Hardware Usage Guide
Cam Screw
Hidden Cam
Arrow
Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the
edge of the board.
Hole
2. 3.
1
2
Insert the CAM SCREW into the HIDDEN CAM.
Tighten the HIDDEN CAM.
HOW TO USE A HIDDEN CAM & CAM SCREW
Turn the CAM SCREW until
the shoulder is against the
surface of the part.
1.
1. Insert the dowel end of the FASTENER into the
hole of the adjoinin part.
NOTE: The dowel end of the FASTENER must
remain fully inserted in the hole of the adjoinin
part while lockin the FASTENER.
2. Tihten the FASTENER with a Phillips
screwdriver as tiht as possible.
Dowel end
2.
Push a TWIST-LOCK® FASTENER
into the lare hole in the part.
1.
HOW TO USE A TWIST-LOCK®FASTENER
427719www.sauder.com/service Pae 5

Step 1 Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratchin your unit or the floor.
å To bein assembly, push four SAUDER TWIST-LOCK®
FASTENERS (7F) into the lare holes in the ENDS (A and B).
å Insert two WOOD DOWELS (15F) into the ENDS (A and B).
427719 www.sauder.com/servicePae 6
A
B
2
7F
Do not tihten the TWIST-LOCK® FASTENERS in this step.
15F
15F
Just think. The sooner
you do this, the sooner
you do somethin else.

Step 2
å Push twelve HIDDEN CAMS (1F) into the ENDS (A and B).
427719www.sauder.com/service Pae 7
A
B
1
(12 used)
1F
Arrow
1F
Arrow

å Turn twenty CAM SCREWS (8F) into the LEGS (F, G, H, and J).
å Insert four WOOD DOWELS (15F) into the LEGS (F, G, H, and J).
Step 3
427719 www.sauder.com/servicePae 8
F
G
H
J
15F
15F
1
8F
(20 used)
15F
8F
8F

å Fasten the LEGS (G and J) to the RIGHT END (A).
Tihten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEGS
insert into the END.
å Fasten the LEGS (F and H) to the LEFT END (B).
Tihten six HIDDEN CAMS.
å NOTE: Be sure the WOOD DOWELS in the LEGS
insert into the END.
Step 4
427719www.sauder.com/service Pae 9
A
B
G
J
F
H
These surfaces
should be even.
1
The LEGS will
overhan this ede.
The LEGS will
overhan this ede.
Ede with
TWIST-LOCK®
FASTENERS
These surfaces
should be even.
Ede with
TWIST-LOCK®
FASTENERS
Groove

å Insert two SAFETY STOPS (29G) into the holes shown in
the RIGHT END (A).
Step 5
427719 www.sauder.com/servicePae 10
This pin must insert
into the location holes
in the RIGHT END (A).
A
4
29G

Step 6
427719www.sauder.com/service Pae 11
å Diaram 1. Usin the cutout above or a tape measure, measure 2-1/2" from one end of the INTERLOCK TRACK (22G).
Position the INTERLOCK TRACK as shown.
å SAFETY STOP / TRACK ATTACHMENT:
Diaram 2. Tilt the first ede of the INTERLOCK TRACK (22G) into the SAFETY STOPS (29G).
å Diaram 3. Rotate the INTERLOCK TRACK and apply force to snap the second ede into the SAFETY STOP.
å Diaram 4. Repeat the SAFETY STOP / TRACK ATTACHMENT for the next SAFETY STOP while holdin the previously
completed SAFETY STOP in its location hole. Repeat these steps until all STOPS have been attached. Visually check
that all INTERLOCK TRACK edes have been snapped into the SAFETY STOPS as shown in Diaram 3.
å Diaram 5. Remove the INTERLOCK TRACK assembly from Diaram 4 and flip it over before insertin the INTERLOCK
TRACK (22G) with SAFETY STOPS (29G) into the roove in the RIGHT END (A).
Be sure the
interlock track
snaps into each
SAFETY STOP.
5.
4.
The interlock system is a safety feature
that prevents more than one drawer
from opening at the same time. Do not
use excessive force to open the drawers.
2-1/2"
1.
29G
22G
Tape Measure
Snap the INTERLOCK TRACK into the
SAFETY STOPS. Do not slide the SAFETY
STOPS onto the INTERLOCK TRACK.
3.
2.
22G
29G
This measurement
needs to be accurate
for the interlock track
to work properly.
Cut out this rectanle
to use as a "spacer"
2-1/2" 4
A
A
F
L
I
P
O
V
E
R
22G
29G
29G
Groove

Step 7
427719 www.sauder.com/servicePae 12
å Separate the EXTENSION SLIDES (45MC) from the EXTENSION RAILS (45MA) as
shown in the upper diaram below. Be prepared, the parts are reasy.
å Fasten the EXTENSION RAILS (45MA) to the ENDS (A and B). Use eiht GOLD
5/16" FLAT HEAD SCREWS (3S) throuh holes #1 and #4.
å NOTE: For each EXTENSION RAIL, turn a SCREW into the hole shown in the
enlared diaram. Then, slide the inner cartride of the EXTENSION RAIL in to find
the other hole that lines up with the hole in the END. Turn a SCREW into this hole.
å NOTE: The EXTENSION SLIDES will be used later for the DRAWERS.
Push the black lever in and pull the SLIDE from the RAIL.
45MA45MC
GOLD 5/16" FLAT HEAD SCREW
(8 used for the RAILS)
3S
3
2
1
1
2
3
4
4
4
7
Open end
Open end
4
7
A
B
After fastening the EXTENSION RAILS to the
RIGHT END (A), the SAFETY STOPS should touch
the top edge of the RAILS. If the gap is larger than
1/16", the drawers could lock up and not open. If
this happens, open two drawers at the same time to
override the interlock system. Remove the drawers
to re-adjust the INTERLOCK TRACK assembly.
3
2
1
1
2
3
4
4

å Fasten the LEFT END (B) to the TOP (C). Tihten two
TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWEL in the END inserts into
the TOP.
Step 8
427719www.sauder.com/service Pae 13
C
B
2
Surface with holes
These surfaces should be even.

å Push eiht HIDDEN CAMS (1F) into the BACKS (K).
å Fasten the BACKS (K) to the LEFT REAR LEG (H). Tihten
four HIDDEN CAMS.
Step 9
427719 www.sauder.com/servicePae 14
1F
Arrow
1F Arrow
1
Surface with HIDDEN CAMS
H
K
K
K
Surface with HIDDEN CAMS
K

å Push four SAUDER TWIST-LOCK® FASTENERS (7F) into
the lare holes in the BOTTOM (D).
Step 10
427719www.sauder.com/service Pae 15
7F
Do not tihten the TWIST-LOCK® FASTENERS in this step.
2
7F
D
Side Step: Make
nachos. (Optional, but
recommended.)

å Fasten the BOTTOM (D) to the LEFT END (B). Tihten two
TWIST-LOCK® FASTENERS.
å Slide the BOTTOM MOLDING* (E) onto the notched ede
of the BOTTOM (D).
å *U.S. Patent No. 5,499,886
Step 11
427719 www.sauder.com/servicePae 16
2
D
B
E
Slide the MOLDING (E)
onto the notched ede.
The roove
is closer to
this ede.
Notched ede

å Fasten the END (A) to the TOP (C) and BOTTOM (D).
Tihten four TWIST-LOCK® FASTENERS.
å NOTE: Be sure the WOOD DOWEL in the END inserts into
the TOP.
å Fasten the RIGHT REAR LEG (J) to the BACKS (K).
Tihten four HIDDEN CAMS.
Step 12
427719www.sauder.com/service Pae 17
12
1
2
K
K
C
D
J
A

å Push one HIDDEN CAM (1F) into a DRAWER BRACE (M63).
å Turn one CAM SCREW (8F) into a DRAWER FRONT (L).
Step 13
427719 www.sauder.com/servicePae 18
1
1F
Arrow
8F
L
M63
(2 used)
(2 used)

Step 14
427719www.sauder.com/service Pae 19
1
å Slide the DRAWER BOTTOM (D729) into the
grooves in the DRAWER SIDES (D32 and D33) and
DRAWER FRONT (L).
D33
Be sure the
DRAWER
BOTTOM
inserts into
the DRAWER
BACK roove.
M63
With the palm of your hand,
tap the DRAWER BOTTOM
down into the roove.
30S
Start each screw a few turns before
completely tihtenin any of them.
BLACK 1-9/16" FLAT HEAD SCREW
(10 used in this step)
1
3
2
4
å Pull the DRAWER FRONT BRACKETS (10G) apart and slide
four into the rooves in the DRAWER SIDES (D32 and D33).
You may need to ently tap them in with a hammer.
å NOTE: The DRAWER FRONT BRACKETS are marked "RH"
and "LH" for easy identification.
å Fasten the DRAWER FRONT (L) to the DRAWER FRONT
BRACKETS (10G). Use four BLACK 9/16" LARGE
HEAD SCREWS (1S).
å Fasten the DRAWER BACK (D61) to the DRAWER
SIDES (D32 and D33) and DRAWER BRACE (M63).
Use five BLACK 1-9/16" FLAT HEAD SCREWS (30S).
BLACK 9/16" LARGE HEAD SCREW
(8 used in this step)
1S
Be sure the DRAWER
BOTTOM inserts into the
DRAWER FRONT roove.
å Fasten the DRAWER BRACE (M63) to the DRAWER
FRONT (L). Tighten one HIDDEN CAM.
L
Surface with
HIDDEN CAM
M63
Unfinished surface
Hidden part usin
recycled material.
Color may vary.
Tap down with your
screwdriver and hammer.
10G
D32
L
Groove
D33
D32
L
D61
D729
D33
D32
11

å Fasten one FILE BRACKET (12B) to the DRAWER BACK (D61). Use
two BROWN 7/16" LARGE HEAD SCREWS (6S).
å Fasten another FILE BRACKET (12B) to the DRAWER FRONT (L).
Use two BROWN 7/16" LARGE HEAD SCREWS (6S).
å Fasten one PULL (98K) to the DRAWER FRONT (L). Use two SILVER
1/4" MACHINE SCREWS (61S), throuh two WASHERS (10I) and
into the DRAWER FRONT.
Step 15
427719 www.sauder.com/servicePae 20
L
D61
The BRACKETS should
be oriented as shown.
12B
12B
BROWN 7/16" LARGE HEAD SCREW
(8 used in this step)
6S
98K
SILVER 1/4" MACHINE SCREW
(4 used for the PULLS)
61S
10I
6S