Producer's PRIDE 1179768 User manual

1
SKU: 1179768，1179769，1179770
PRAIRIE COOP
(115 in. L x 55.9 in. H x 53.1 in. W)
Distributed by:
TRACTOR SUPPLY COMPANY
5401 VIRGINIA WAY,
BRENTWOOD, TN 37027
For customer support, call: 1-888-376-9601
www.TractorSupply.com
MADE IN CHINA

2
CARE INSTRUCTIONS
SAFETY INFORMATION:
DANGER: Please keep children out of assembly area during assembly.
WARNING: This product is designed exclusively for chickens. Not intended for
children.
BEFORE YOU BEGIN:
Read instruction prior to assembly. This product contains parts that can be damaged if
incorrectly assembled. Please follow instructions. For steps where parts are placed
upside down, place parts on a smooth surface to avoid scratching finish. Locate a flat
level surface area to assemble and place coop for best results.
PRE-ASSEMBLY:
TOOLS REQUIRED (not included):
Power Gun with Phillips Head Bit
Adjustable Wrench
Ruler
Two people are recommended to assemble this product.
PRODUCT OVERALL VIEW

3
PARTS LIST
Part
Image
Description
Quantity
1
Roof cap
1pc
2
Top roof panel
2pcs
3
Lower roof panel
2pcs
4
Nesting roof
1pc
5
Back coop panel
1pc
6
Front coop panel
1pc

4
7
Right bottom panel
1pc
8
Left bottom panel
1pc
9
Left top side panel
1pc
10
Right top side panel
1pc
11
Top front and back
panel
2pcs
12
Right & left nesting
panels
2pcs
13
Nesting floor
1pc

5
14
Back nesting panel
1pc
15
Drawer
1pc
16
Run side panel 1
1pc
17
Run side panel 2
1pc
18
Run side panel 3
2pcs
19
Run side panel 4
1pc

6
20
Run side panel 5
1pc
21
Run left cover panel
2pcs
22
Run right cover panel
1pc
23
Right run panel
1pc
24
Roosting bar
2pcs
25
Nesting box divider
2pcs
A
Screws 3.5*60mm
12+1pcs
B
Screws 3.5*40mm
48+1pcs

7
C
Screws 3.5*35mm
26+1pcs
D
Screws 3*30 mm
4+1pcs
E
Screws 3*16 mm
18+1pcs
F
Support arm
1 pair
G
Latch
1pc
H
Door pull lever
1pc

8
CAUTION: If using a cordless power drill / screwdriver, turn torque setting
down to a minimum level to start so that screws are not stripped. Adjust torque
up slightly if needed to fully tighten screws.
ASSEMBLY INSTRUCTION
Step 1: Attach the right bottom panel (7) to the run side panel (16) (17) using screws
(C)*4pcs.
Step 2: Attach the right top side panel (10) using screws (C)*2pcs as shown.

9
Step 3: Attach the front coop panel (6) using screws (B)*4pcs as shown.
Step 4: Attach left bottom panel (8) to the front panel using screws (B)*3pcs as shown.

10
Step 5: Attach the back coop panel (5) using screws (B) *7pcs as shown.
Step 6: Attach the left top side panel (9) using screws (B)*2pcs as shown first, and
then install the roosting bar (24) in the coop as seen in the picture below.

11
Step 7: Attach the top front and back panels (11) to the left and right top side panels
using screws (B)*8pcs as shown.
Step 8: Attach the right and left nesting panels (12) using screws (C)*4pcs as shown.

12
Step 9: Place the nesting floor (13) inside the nesting area first, and then place the
nesting box divider (25) as shown.
Step 10: Attach the back nesting panel (14) to the nesting panels using screws
(B)*4pcs as shown.

13
Step 11: Attach the nesting roof (4) to panel using screws (E)*4pcs as shown.
Step 12: Open the nesting roof and attach the support arms (F) to the nesting roof
panels using screws (E)*8pcs.
Note the left and right direction of the support arms.

14
Step 13: Attach the latch (G) to back nesting panel and nesting roof using screws
(E)*6pcs as shown.

15
Step 14: Attach the run side panels (18) (19) (20) to each other using screws
(A)*12pcs.
Step 15: Attach the right run panel (23) to the run side panels using screws (B)*6pcs
as shown.

16
Step 16: Attach the run left cover panel and the run right cover panel to the run side
panels using screws (B)*14pcs as shown.
Step 17: Attach the lower roof panels (3) to the side panels using screws (C)*8pcs as
shown. Place the door pull lever (H) through hole in panel, and secure into place by
threading into door hardware located at the center of the sliding coop door.

17
Step 18: Attach the top roof panels (2) using screws (C)*8pcs as shown.
Step 19: Attach the roof cap (1) using screws (D)*4pcs as shown.

18
Step 20: Place the drawer (15) as shown.
Finished Coop