Producer's PRIDE Hill Country Coop Installation guide

1
SKU: 1277537
Hill Country Coop
(114 in. L x 57.8 in. H x 56.3in. W)
Distributed by:
TRACTOR SUPPLY COMPANY
5401 VIRGINIA WAY,
BRENTWOOD, TN 37027
For customer support, call: 1-888-376-9601
www.TractorSupply.com
MADE IN CHINA

2
CARE INSTRUCTIONS
SAFETY INFORMATION:
DANGER: Please keep children out of assembly area during assembly.
WARNING: This product is designed exclusively for chickens. Not intended for
children.
BEFORE YOU BEGIN:
Read instruction prior to assembly. This product contains parts that can be damaged if
incorrectly assembled. Please follow instructions. For steps where parts are placed
upside down, place parts on a smooth surface to avoid scratching finish. Locate a flat
level surface area to assemble and place coop for best results.
PRE-ASSEMBLY:
TOOLS REQUIRED (not included):
Power Gun with Phillips Head Bit
Adjustable Wrench
Ruler
Two people are recommended to assemble this product.
PRODUCT OVERALL VIEW

3
PARTS LIST
Part
Image
Description
Quantity
1
Roof cap
1pc
2
Top roof panel
2pcs
3
Nesting roof
1pc
4
Back coop panel
1pc
5
Front coop panel
1pc
6
Right coop panel
1pc

4
7
Left coop panel
1pc
8
Right & left nesting
panels
2pcs
9
Nesting floor
1pc
10
Back nesting panel
1pc
11
Drawer
1pc
12
Run side panel 1
1pc
13
Run side panel 2
1pc

5
14
Run side panel 3
1pc
15
Run side panel 4
1pc
16
Run side panel 5
2pcs
17
Right run panel
1pc
18
Run left cover panel
2pcs
19
Run right cover panel
1pc
20
Roosting bar for run
2pcs

6
21
Roosting bar
3pcs
22
Nesting box divider
2pcs
23
Support bar
4pcs
A
Screws 3*16mm
12+1pcs
B
Screws 3.5*35mm
20+1pcs
C
Screws 3.5*40mm
56+1pcs
D
Screws 3.5*60 mm
12+1pcs
E
Door pull lever
1pc
F
Support arm
1pair

7
CAUTION: If using a cordless power drill / screwdriver, turn torque setting
down to a minimum level to start so that screws are not stripped. Adjust torque
up slightly if needed to fully tighten screws.
ASSEMBLY INSTRUCTION
Step 1: Attach the right coop panel (6) to the run side panel (12) (13) using screws
(B)*4pcs.
Step 2: Attach left coop panel (7) to the front coop panel (5) using screws (C)*6pcs.

8
Step 3: Attach the back coop panel (4) to the left and right coop panel using screws
(C)*6pcs as shown.
Step 4: Place the roosting bars (21) in the coop, Using screws (B)*2pcs as shown.

9
Step 5: Attach the right and left nesting panels (8) using screws (B)*6pcs as shown.
Step 6: Place the nesting floor (9) inside the nesting box. And then install the nesting
box divider (22) as shown.

10
Step 7: Attach the back nesting panel (10) to the nesting panels using screws (C)*4pcs
as shown.
Step 8: Attach the nesting roof (3) to panel using screws (A)*4pcs as shown.

11
Step 9: Open the nesting roof and attach the support arms (F) to the nesting roof
panels using screws (A)*8pcs.
Note the left and right direction of the support arms.
Step 10: Attach the run side panels (14) (15) (16) to each other using screws (D)*
12pcs as shown.

12
Step 11: Attach the right run panel (17) to the run side panels using screws (C)*6pcs
as shown.
Place the roosting bar for run (20) as shown and secure using screws (C)*4pcs.
Step 12: Attach the run left cover panel (18) and the run right cover panel (19) to the
run side panels using screws(C)*14pcs as shown.

13
Step 13: Place the support bar (23) to the top roof panels (2) using screws (C)*12pcs
as shown. Then place the roof on the top of coop and secure in place using screws
(B)*8pcs.
Step 14: Attach the roof cap (1) using screws (C)*4pcs as shown.
Place the door pull lever (E) through hole in panel and secure into place by threading
into door hardware located at the center of the sliding coop door.

14
Step 15: Place the drawer (11) as shown.
Finished Coop