Profelmnet 3433 User manual

Proedrou Drakaki 11 ,173 41Agios Dimitrios
Tel: [phone], Fax: [phone]
www.profelmnet.com
3433
Control panel for sliding gate motor- single swing gate motor-barrier up to 1200watt
Function Description
1 DECELARATION
OFF: NO decelaration
ON: With deceleration, that starts
1sec. before the end-route of the gate and continues for
40sec. or until the terminal switches are reached. If there are
not terminal switches, the deceleration continues for 15
seconds.
2 BRAKE
OFF: No motor brake
ON: Brake when the gate reaches the end of the route. This
function should only work with the deceleration function.
3 AUTO CLOSE FUNCTION
OFF: No auto close
ON: Embedded auto close function. Works with the photocell.
When the gate opens and there is no access (no obstacle
detection from the photocell), the A/C time is 120 seconds (the
gate will close after 120 seconds). If there is access and
obstacle detection from the photocell, then the A/C time is 10
seconds (the A/C timer counts 10 seconds after the photocell
is free and then the gate will automatically close). The second
time of A/C can be changed (follow the below instructions).
4 TERMINAL SWITCHES
OFF:NO terminal switches. In case of single swing gate or
rolling shutter
ON: Terminal switches. In case of sliding gate or barrier.
5 PHOTOCELL
OFF: NO photocells.
ON: Photocells. The power supply of the photocell 24VAC in
terminal 13&14 and COM & NC of the photocell in terminal 9
and 10
6 ADJUSTABLE DECELARATION
OFF: motors up to 800kg
ΟΝ:motors above 800kg
7 MOTOR POLARITY CHANGE
OFF/ON: The first move of the motor after power reset needs
to be opening, when auto close is disabled. If not, switch the
dipswitch 7 to the opposite position.
8 SAFETY EDGE
OFF: Safety edge disabled
ON: Safety edge enabled. When activated the door stops and
moves back 10 cm.
Code
Frequency
Codification
Terminal
Switches
Photocel
ls
Ext.
Button
Auto Close
Light
230V
Motor
torque
Slow
move
Pedestrian
move
Memory
3433
433,92
Κατά παραγγελία
ΝΑΙ
ΝΑΙ
ΝΑΙ
ΝΑΙ
ΝΑΙ
ΝΑΙ
ΝΑΙ
ΝΑΙ
300

Proedrou Drakaki 11 ,173 41Agios Dimitrios
Tel: [phone], Fax: [phone]
www.profelmnet.com
Functions and connections
Power Supply 230 VAC
Supply the control panel with 230V.Check that the yellow indication
light is ON. Press the button of the transmitter and check the red
indication light is ON. The first gate move after power-up (230V) is
the OPEN direction, otherwise place the dipswitch 7 in the opposite
position.
Clear transmitter memory
Press CODE button continuously. The red indicative LED turns ON. Keep
pressing CODE button until the red indicative LED goes COMPLETELY
OFF. Release CODE button. The memory is erased.
Adding new transmitter from control panel:
Press the CODE button until the red indicative LED turns ON. Release
immediately the CODE button and press the transmitter’s button. The
red indicative LED blinks once as an indication of successful save.
Adding new pedestrian transmitter from control
panel
Press the CODE button continuously until the red led starts blinking.
Then release the code button and press immediately the transmitter
button. The red indicative LED blinks once as an indication of successful
saving of pedestrian transmitter
Working time:
While the gate is fully closed, press and keep the TIME button of
the control panel pressed until the gate goes to fully open position.
Then leave it. The working time is saved.
Working time pedestrian:
While the gate is fully closed press the TIME button until the red led is
turned ON release the button and press it again steadily for as long as
you want the pedestrian time.
Adjust motor force:
The motor power adjustment for the normal motor speed will
ONLY be made while the user is programming the working time
using the trimmer of the automation. The user will be able to
adjust and control the force of normal motor speed while
programming working time. After the program of working time, the
motor force will also be automatically saved. If the user wishes to
change the motor's force, it must again program the working time.
Adding a new transmitter remotely:
The motor is fully closed or open. Press a working transmitter
button (already in memory) to start the motor working and hold it
pressed until the motor stops. When it stops, leave it and press the
new transmitter button immediately. The new transmitter is saved.
Repeat steps to program more transmitters remotely. When the
memory is full (300 transmitters) you cannot add more new
transmitters.
Photocell connectionsΤοποθέτηση φωτοκύτταρου:
Photocell power supply =>Connect to terminals 13-14
Photocell command C και NC => Conncet to terminals 9 & 10.
Adjusting auto close time:
There is a double counter in the A/C function. The first one is 120
seconds and is applied when the door stops after an open function.
During this counting time of 120 sec., if the photocell beam is
disturbed, then after the beam is free, the A/C counting time
becomes 10 sec. until the fully closed position. In this control panel,
the second counting time of 10 sec., can be regulated. Press the
TIME button, keep it pressed and within 1 sec , press the CODE
button. The red indicating light starts flashing, indicating the
seconds of the counter. The time of the counter is from 1-120
seconds. Keep it pressed for the time you wish to give in A/C and
pedestrian function. The dipswitch 3 needs to be ON.
Decelaration:
Light Function:
Light can be connected on terminals 1+3 which has two functions
-Flashlamp (default function). The light is flashing for as long as the
motor moves
-Steady light (3 minutes). The light is turned on steadily for 3 minutes
after the last command
To change between those two functions we should turn the power off ,
press CODE button and TIME button simultaneously and turn the
power back ON. The red led stays ON and then we release the two
buttons. Light function has been changed successfully.
For motors up to 800kgs
Program 6 of the control board=> OFF
And we adjust the power of deceleration of
the trimmer of the control board
For motors above 800kgs
Program 6 of the control board=> ON
And we adjust the power of deceleration of
the trimmer of the control board