NAPCO GEM-P800 User manual

WI850E 04/10
© NAPCO 2010
®
GEM-P800
Control Panel / Communicator
Installation Instructions

WI850D GEM-P800 Installation Instructions
2
General Information
The GEMINI GEM-P800 control panel provides up to
6 hardwired/wireless zones, a 2-wire fire zone and 2
wireless only zones. Up to eight 4-digit user codes
can be programmed. Ambush, when selected, uses
User 8 code as an Ambush code.
The GEM-P800 is wireless ready. When used with a
GEM-RECV-XP8 receiver, the control panel can sup-
port up to 8 wireless zones, 4 wireless smoke detec-
tors and 4 Keyfobs.
The GEM-RP8 keypad provides complete control of
the GEM-P800 control panel. Information on system
status, bypassed zones, system troubles etc. can be
viewed at the keypad.
The control panel can be easily and quickly pro-
grammed from the keypad. The panel can also be
locally or remotely downloaded using PCD3000 soft-
ware and a PCI 2000/3000 interface or PCL2000A
local Download cable. See Downloading Section
(page 5) for more information.
GEM-P800 Features
Control Panel
•8 Zones (6 Hardwired/Wireless + 2 wireless)
•2-wire Fire Zone
•3 Keypad Panics
•Wireless Ready
•Bell Supervision
•Line Cut Detection
•Answering Machine Override (Second Call)
•50 Event Log
Communicator
•2 Telephone Numbers
•Backup Reporting
•Pager Format
•Point ID Format
•Individually Report 8 Users
•Opening after Alarm Report (Cancel Code)
•Conditional Closing Report
For Technical Assistance, Contact the NAPCO Toll Free Helpline 
[phone]
NAPCO Security Technologies, Inc.
333 Bayview Avenue, Amityville, New York 11701
For Sales and Repairs, call Toll Free: [phone]
Table of Contents
General Information...............................................2
GEM-P800 Features .............................................2
Specifications ........................................................3
UL Compatible Smoke Detectors ..........................4
Listings and Approvals ..........................................4
Ordering Information .............................................4
Optional Accessories.............................................4
Programming the Panel.........................................5
Installation .............................................................6
Wiring ....................................................................6
Keypad Operation .................................................7
Panel Operation ....................................................8
Bypassing .............................................................9
User Program Mode ..............................................9
GEM-P800 Commands .......................................10
Dealer Commands .............................................11
Wireless Operation (Signal Strength) ................11
Zone Features.....................................................12
System Times......................................................13
System Features .................................................14
Telephone Number 1 Programming ....................15
Backup Telephone Programming ........................16
Pager Programming ............................................17
Telephone Number 3 Programming ....................18
Report Codes ......................................................18
Enhanced Communicator Features ..................... 19
Wireless ..............................................................19
Downloading........................................................20
Dealer Programming ...........................................21
System Troubles .................................................23
Troubleshooting...................................................25
Wiring Diagram....................................................27
Warranty..............................................................28

3
Specifications
Current & Voltage Ratings
Alarm Output --------------------------------- Burg: 12 VDC, 2A (max.)
Fire: 12 VDC, 65 mA
Output Current Limiting -------------------- Burg/Fire: 2.25 A
AUX Power: 750 mA
Residential Burglary (4 Hour Standby)
Combined Standby Current:-------------- 500 mA
Bell Output: ----------------------------------- 2 A
(Using Rechargeable 12 VDC 4 AH BATTERY, minimal requirement)
Residential Fire (4 Hour Standby)
Combined Standby Current:-------------- 500 mA
Bell Output: ----------------------------------- 65 mA
(Using Rechargeable 12 VDC 4 AH BATTERY, minimal requirement)
Residential Fire (24 Hour Standby)
Combined Standby Current:-------------- 120 mA
Bell Output: ----------------------------------- 95 mA
(Using Rechargeable 12 VDC 7 AH BATTERY, minimal requirement)
Transformer and Battery
Required Transformer: -------------------- NAPCO TRF12 OR
BASLER 16.5 VAC 20VA
Required Battery: --------------------------- 12V 4 AH or 7 AH Rechargeable
Change Battery every 5 years or as required
Maximum Charging Current: ------------- 165 mA
Maximum Input Current: ------------------- 2.58 A
Loop Characteristics
Loop Voltage: --------------------------------5 Volts
Loop Current :---------------------------------Zones 1, 2, 3: 0.9 mA (2.2 K)
Zones 4, 5, 6: 0.5 mA (3.9 K)
Loop Resistance:-----------------------------100Ω per zone (max.)
Device Specifications
Max # keypads:-------------------------------4, GEM-RP8 current = 65 mA
Max # of receivers: --------------------------2, GEM-RECV-XP8
current = 65 mA each
Max # of compatible
2-wire smoke detectors : ------------------10
Max Keypad wire length : ----------------1000’ total wire length
Miscellaneous
Housing Dimensions : ---------------------11" x 121/8"x 3"
(28 x 30.8 x 7.6) HxWxD
Shipping Weight: ---------------------------GEM-P800 5.5 lbs.
Operating Temperature:--------------------0-49ºC (32-120°F)

WI850D GEM-P800 Installation Instructions
4
Mfg 4-Wire
Smoke Detector
2-Wire
Smoke Detector
Smoke
Detector
Base
Napco
Sentrol
449AT
449C
449CRT
449CST
449CSRT
449CSRH
449CSST
449CLT
449CSLT
449CTE
741U
742U
712U
722U
732U
711U
721U
721UT
731U
701U
702U
702RE
702RU
System
Sensor
1112
2112
2112T
2112TSRB
2100
2100T 1100
FW-2S (FW-RM1 required)
8 zone Control Panel with 2-wire Fire
(6 Hardwire/Wireless+2 wireless)
Keypad
Zone Doubling Resistors (2.2K & 3.9K)
Operating Instructions GEM-P800
Programming Instructions GEM-P800
GEM-P800
GEM-RP8
ZDR
OI219
WI851
Ordering Information
Optional Accessories
*Wireless Receiver
Window/Door Transmitter
Keyfob Transmitter
Wireless Smoke Detector
Wireless PIR
Wireless Dual-Technology Sensor
Wireless Glass-Break Detector
Relay Board
Audio Verification Module
Downloading Software for IBM PC Compatibles
Software with Interface for IBM PC Compatibles
(Includes PCL2000A Local Download cable)
Local Download cable
GEM-RECV-XP8:
GEM-TRANS2
GEM-KEYF:
GEM-SMK:
GEM-PIR:
GEM-DT:
GEM-GB:
RB1000
Veriphone:
PCD3000:
PCI2000/3000:
PCL2000A
Listings and Approvals
UL HOUSEHOLD FIRE AND BURGLARY WARNING SYSTEM CONTROL
UNIT
STANDARDS # 1023, 985
VERIFIED TO COMPLY WITH F.C.C. PART 15 AS CLASS B : DIGITAL
DEVICE
UL Compatible Smoke Detectors
GEM-P800 Compatible Smoke Detectors (Approved by UL)
*Supports up to 8 zones, 4 Key Fobs, 4 Smoke Detectors.
Note: Wireless and Access Features have not been evaluated by UL.

5
Programming the Panel
Refer to GEM-P800 Programming Instructions (WI851)
Defaulting the Panel
1. Remove power from the panel.
2. Remove all wiring from terminal 15 (PGM)
and terminal 3.
3. Connect terminal 15 (PGM) to terminal 3.
4. Apply power to the GEM-P800 control panel.
5. After a few seconds the ARMED, READY
and HSYSTEM TROUBLE LED's will flash.
6. The keypad will beep 3 times indicating the
panel default values have been loaded.
7. Remove wiring between terminal 15 (PGM)
and terminal 3.
8. Re-install original wiring for terminal 15
(PGM) and terminal 3.
Keypad Programming
Refer to WI851 for information on keypad pro-
gramming.
Downloading
The GEM-P800 panel can be download/
uploaded with PCD3000 software using the Ring
Method, Answering Machine Override (Second
Call) or A6 Method of downloading.
The panel can also be automatically
downloaded/uploaded using PCD2000 Software
running
PCPreset. For Site Initiated Downloaded, see
Auto Download ID Number [93].
Local Downloading
Wire as shown in Figure 1. Use the power up or
A6 method of establishing a connection. The
power up method is recommended if the panel is at-
tempting to report.
Remote Downloading
Wire as shown in Figure 2. The panel can be
remotely download/uploaded using any one of
the following methods:
1. The A6 method
2. Call-in method
3. Answering Machine Override (Second
Call)
4. Site-Initiated (PCPreset & A6)
5. Automatic Downloading (Using PCPreset)
MODEM
J1
TO COMPUTER
J3
LOCAL
TO
PCI2000
J2
TO EXTERNAL
MODEM
J4
TELCO
J5 LINE
OUT TO
TELCO
FIGURE 2REMOTE DOWNLOAD
PGM
(-)
[phone] 19
+PWR GND GREEN
PHONETELCO
GREEN
RED
GEM-P800 Panel at the site
RINGTIP RING
RJ31X
TIP
GRY
BRN
PGM
(-)
[phone] 19
GREEN TIP RING
PHONE
PCL2000A
GREEN
RED
MODEM
FIGURE 1LOCAL DOWNLOAD
TIP RING
TELCO
GND+PWR
BLACKRED
NOTE:
Any programming in Dealer Options 1 [96] and Dealer
Options 2 [97] will not be defaulted. If Dealer Code Lock-
out has been programmed the panel will not default the
Dealer Code.

WI850D GEM-P800 Installation Instructions
6
Installation
Mounting the Panel
Mount the Panel close to an unswitched AC
source, a cold-water pipe ground, and a tele-
phone line connection.
Mounting the Keypad
A keypad should be located near an exit/entry
door. To remove the keypad from the backplate,
insert a small screwdriver into the slots at the
bottom of the keypad. Pull up on the screw-
driver to pop off the cover.
Up to 4 keypads can be connected on individual
wire runs with #22 AWG wire with a maximum
total cable length of 1000 feet. Each keypad
draws approximately 65 mA.
Typical Fire Installation
(Where permitted by local codes)
Install smoke detectors outside each sleeping
area and on each floor, including the basement.
Install the living room and basement smoke de-
tectors near the stairway of the next upper level.
For increased protection, additional detectors
should be installed in areas other than those
required, such as the dining room, bedrooms
and utility room. Heat detectors, rather than
smoke detectors, are recommended in kitchens,
attics, and garages due to conditions that may
result in false alarms and improper operation.
Refer to NFPA Standard 74 (National Fire Pro-
tection Association, Batterymarch Park, Quincy,
MA 02269) for additional information, including
proper mounting methods.
Wiring
Terminal Block Wire Range: 14-22 AWG.
Grounding the Panel
Connect the control-panel EARTH GROUND
screw through a No. 16 AWG or larger wire to a
metal cold-water pipe, a UL Listed ground rod,
or an AC ground connector. Do not use a gas
pipe or a plastic pipe. Use at least #16 AWG
wire. Connect a wire with a ground lug crimped
or soldered onto one end and connect it to the
EARTH GROUND screw in the cabinet.
AC Power and Battery Wiring
Complete all wiring before connecting the bat-
tery or AC Power. Do not plug the transformer
into a switched outlet.
Telephone Wiring
Wire as shown in the wiring diagram in the back
of this manual.
WARNING
The FCC restricts the use of this equipment on
certain telephone lines. Read the FCC state-
ment on the back of this manual to ensure com-
pliance.
Keypad Wire Color Control Panel Terminal
RED 12 (+PWR)
BLACK 13 (GND)
GREEN 14 (GREEN)
TABLE 1 KEYPAD WIRING
FIGURE 3Typical Fire Installation

7
Burglary Zone Wiring
NAPCO's EZ Zone DoublingTM is simple. Each
terminal has 2 zones, use an E(2.2 K) type
Zone Doubling Resistor for the primary zone
and a Z(3.9 K) type Zone Doubling Resistor for
the secondary zone.
Wire zones as shown in the wiring diagram (pg.
27). All resistors must be installed, even if the
zone is not used. If required, unsupervised
open circuit devices may be used instead of
closed circuit devices. Program the zone as an
Open Circuit Zone [06] (Zone Doubling Resistor
required). If necessary, use the voltage chart
below to verify proper voltages.
Fire Zone Wiring
Wire the Fire Zone as shown in the Wiring Dia-
gram in the back of this manual. An EOL resis-
tor must be installed, even if the Fire Zone is not
used. In UL installations, use a UL Listed
NAPCO EOL 2.2K resistor.
PGM Wiring
The PGM is a switched negative output that is
activated depending on the programming option
(s) that have been selected [08], [23] - [25].
Connect the device controlled by the PGM be-
tween +PWR and the PGM terminal (maximum
load of 50 mA).
Keypad Operation
Keypad zone LED's indicate zone status.
ARMED, STATUS and HSYSTEM LED's pro-
vide system status. The keypad sounder pro-
vides feedback beeps for correct and incorrect
entries.
Keypad Sounder
3 QUICK BEEPS
Panel Armed (System ON)
Chime ON
Fault Find Mode ON
Keypad Sounder ON
Zone Bypassed
6 QUICK BEEPS
Panel Disarmed (System OFF)
Chime OFF
Fault Find Mode OFF
Keypad Sounder OFF
Zone Un-Bypassed
1 SECOND - STEADY TONE
Incorrect Code Entered
Invalid key entry
4 LONG BEEPS (PRIORITY CONDITION)
1. Entering an Arm Code with a faulted zone
(Not an Auto-Bypass Reentry Zone).
2. Entering an Arm Code when the Bell or
PGM is ON (Bell and PGM will turn OFF).
3. Arming with the Fire LED ON - reset re-
quired. Press the Ckey.
Terminals 2.2 K Primary 3.9 K Secondary
3&4 Zone 1 Zone 4
5&4 Zone 2 Zone 5
6&7 Zone 3 Zone 6
TABLE 2 EZ ZONE DOUBLING™
Fire Zone Normal 13.0V
Fire Trouble 13.8V
Fire 0.0 V
TABLE 4 VOLTAGE AT FIRE ZONE (Terminals 8 & 9)
Primary (2.2K) and Secondary (3.9K) zones normal 1.9 V
Secondary (3.9K) open 2.5 V
Primary (2.2K) open 3.2 V
Primary (2.2K) and Secondary (3.9K) open 5.0 V
Primary (2.2K) and/or Secondary (3.9K) shorted (Sys. Trbl 7-Zone Trbl) 0.0 V
TABLE 3 VOLTAGE AT TERMINALS 3&4, 5&4, 6&7

WI850D GEM-P800 Installation Instructions
8
Keypad LED's
ARMED LED DEFINITION
Armed ............................................................ON
Instant Mode .................................... Rapid Flash
Zone in Alarm ........................................Flashing
STATUS LED DEFINITION
Ready to be Armed........................................ON
Zone faulted................................................. OFF
HTROUBLE LED DEFINITION
AC Failure..............................................Flashing
System Trouble(s) ........................................ON
IFIRE LED DEFINITION
Fire Alarm ..............................................Flashing
Fire Memory / *Fire Trbl.................................ON
*See Note 1
AC LED DEFINITION
AC Present ....................................................ON
AC Failure ................................................... OFF
ZONE LED DEFINITION
Faulted Zone..................................................ON
Bypassed Zone.................................Slow Flash
Zone in Alarm ........................................Flashing
Panel Operation
Arming (System ON)
Before arming the system close all protected
zones (unless programmed as Auto-Bypass
Reentry Zones). Enter a 4-digit Arm/Disarm
code, followed by the Dkey, the keypad will
provide a feedback beep for each key pressed.
If a valid Arm/Disarm code is entered, the key-
pad will beep 3 times. If an incorrect Arm/
Disarm code is entered, the keypad will sound a
1-second tone indicating an incorrect entry.
Arming without Entry Delay (Instant
Mode)
Enter the Fkey to eliminate the entry delay.
The ARMED LED will flash rapidly to indicate
the panel is in Instant Mode. If an Exit/Entry
Zone is tripped while the panel is in Instant
Mode the panel will go into alarm immediately.
Arming/Disarming with a Keyfob
The system can be armed by pressing the K
key, and disarmed by pressing the Lkey on
the Keyfob. Zones programmed as Exit/Entry
Follower Zones can be bypassed when the M
or Nkeys on the Keyfob have been pro-
grammed for Interior [81-84]. Zones pro-
grammed as Home/Away with Delay Zones can
be armed regardless of the state of the Exit/
Entry Zones when the Mor Nkeys on the
Keyfob have been programmed for Full Set [81-
84]. To arm the system with all zones protected
press the Kkey. Press and hold the Mor
Nkey for 1.5s to fully set the system (the LED
on the Keyfob indicate the Keyfob has transmit-
ted the signal). Program Keyfob/Keyswitch Chirp
[23-4] for an audible indication of system arming
and disarming.
Arming/Disarming with a Keyswitch
The system can be armed/disarmed by using a
momentary Keyswitch wired to Zone 6. Pro-
gram Keyfob/Keyswitch Chirp [23-4] for an audi-
ble indication of system arming and disarming.
Arming Instant with a Keyfob
The panel can be ARMED INSTANT when the
Mor Nkeys on the Keyfob have been pro-
grammed for Instant [81-84]. To arm the sys-
tem with Instant protection press the Kkey,
then press and hold the Mor Nkey for 1.5s
to arm the panel with INSTANT protection.
Disarming (System OFF)
After entering the premises through an Exit/
Entry Zone, the keypad will sound the Entry De-
lay Tone. Enter a valid Arm/Disarm code, then
* If Fire Trouble on Fire LED [96-4] has been enabled, a steady
Fire LED will indicate Fire Trouble.
NOTE:
Faulted Keyswitch or silent 24 hour zone normally do not
display at the keypad. If a silent 24 hour zone or Keyswitch
is faulted at the time of arming the faulted zone will display
only while the priority sound is ON.
NOTE:

9
press D. If a valid Arm/Disarm code is entered,
the keypad will beep 6 times, indicating the
panel has been disarmed. The red Armed LED
will go out. If an incorrect Arm/Disarm Code is
entered, the keypad will sound a 1-second tone,
indicating incorrect entry. Press the Ckey
and re-enter the code.
Disarming after an Alarm (Alarm Memory)
The armed LED and the zone(s) that caused the
alarm will be flashing. Disarm the panel. The
system is currently not detecting zone faults or
displaying system trouble. The zone(s) that
caused the alarm will continue to flash. The
STATUS and HSYSTEM TRBL LED's are out
indicating:
•The system is displaying Alarm Memory.
Press the Ckey to clear Alarm Memory.
Bypassing
Automatic Bypassing
Home/Away with Delay Zones
This zone type has the following operation de-
pending on whether an Exit/Entry Zone has
been violated during the Exit Delay time.
Home
Exit/Entry Zone is not violated
Zones selected as Home/Away with Delay
Zones will be bypassed automatically.
Away with Delay
Exit/Entry Zone is violated
Zones selected as Home/Away with Delay
Zones will have a fixed 20-second entry
delay when violated before an Exit/Entry
Zone.
Full Setting the System with Automatic
Bypassing - Home/Away with Delay
Zones
From the Keypad
Press BC to return protection to
Home/Away with Delay Zones that have
been automatically bypassed. Three min-
utes are allowed to walk through Exit/Entry
and Exit/Entry Follower Zones.
Using A Keyfob (GEM-KF)
All zones in the system can be armed re-
gardless of the state of the Exit/Entry Zone
when arming with a Keyfob and using an
AUX key programmed as Full Set. Press
Kand press and hold the Mor N
keys for 1.5s when leaving the premises. All
zones, including Home/Away Zones are
armed..
Bypassing a zone
Press the Bkey, then the zone number to be
bypassed. While the panel is DISARMED, the
bypassed zone LED will flash slowly; indicating
the zone has been bypassed. While the panel is
ARMED, the bypassed zones will only be dis-
played if the Display Bypassed [21-3] option has
been selected.
Unbypassing a zone (Disarmed only)
Press the Bkey then the number of the
zone to be unbypassed.
Group Bypass
Press the Ekey to Bypass all Exit/Entry
Follower Zones [02] or Home/Away Zones
[01] (only if the system is programmed ex-
clusively for Home/Away with Delay
zones).
.
Using A Keyfob (GEM-KF)
Hold the Mor Nkey on the Keyfob to
Bypass all Exit/Entry Follower Zones [02] or
Home/Away Zones [01] (only if the system is
programmed exclusively for Home/Away
with Delay zones).
User Program Mode
To prevent the loss of the User 1 Code, the
panel default program includes User 1 Code
Lockout [96-2].
To change the User 1 Code from its default

WI850D GEM-P800 Installation Instructions
10
value of 1234, program the 4-digit User 1 Code
through Dealer Programming [95]. User 1 Arm/
Disarm code is also used to program User
Codes 2 - 8. By default, the User 1 code cannot
be re-programmed by the user.
If it is necessary to change the User 1 code, it
can be changed through downloading or Dealer
keypad programming. From Dealer Program
Mode, change the User 1 Code Lockout ([96-2]
LED=OFF) to disabled.
Your User 1 Code can be used to enter the User
Program Mode, where you can program other
User Codes. The following explains how you
will use this Code to program or erase additional
User Codes.
Entering User Program Mode
1. Enter A8
2. Enter User 1 Code (1234)
(Default)
3. Press D
While in User Program Mode, Zones 1 through 8
will light to indicate any User Codes presently
programmed. Follow the example below to pro-
gram User 2's code to 1923.
User Mode Programming Example:
1.Press 2, keypad will beep twice and
Zone 2 LED will Flash.
2.Enter 1923, Zone 2 LED will
continue to flash until the 4th digit is en-
tered. The keypad will beep 4 times con-
firming a valid entry (Zone LED steady).
Deleting a User Code
Press the User number to be deleted, the key-
pad will beep twice and the zone LED will be
flashing indicating the user has been selected.
Press F, and the LED associated with the
user will now be OFF.
Exiting User Program Mode
When you are done programming or erasing
User Codes, press Cto exit. The Armed,
Status, and Hlights will stop flashing, and you
can test your new User Code. IMPORTANT:
You MUST exit User Program Mode before
testing your new User Code.
GEM-P800 Commands
User Commands
A1 Bell Test
Enter this command to turn on the Bell, keypad
sounder and keypad LED's for 2 seconds. The
battery is tested during a Bell Test, and auto-
matically every *24 hours to ensure proper bat-
tery operation under load. The Alarm output
requires a battery in order to supply the speci-
fied output. If the battery cannot sustain the
load, a low battery indication will be displayed.
A battery test is also performed on power-up
after a 3 minute delay.
*A battery test occurs every 4 hours when
Household Fire [96-3] has been selected.
DEasy Arm
Press this key to arm the panel. To disarm the
panel a valid Arm/Disarm code must be entered.
Requires Easy Exit/Easy Arm [21-2] to be en-
abled.
EInterior
Enter this command to bypass all Exit/Entry Fol-
lower Zones or Home/Away Zones (only if the
system is programmed exclusively for Home/
Away with Delay zones).
FInstant
Enter this command before or after arming to
remove the entry delay on Entry/Exit Zones.
The keypad ARMED LED will flicker rapidly.
Faulting a Exit/Entry Zone will result in an imme-
diate alarm.
A5 Chime ON/OFF
Enter this command to turn chime ON/OFF.
The Keypad will chime on any zone that has not
ARMED, STATUS AND HSYSTEM TROU-
BLE LED’s WILL FLASH CONTINUOUSLY.
KEYPAD WILL BEEP 4 TIMES.
ARMED
H
GEMINI
STATUS
1
A 1 is displayed indicating
User 1 Code is programmed
and 2-8 are blank.
Zone LED Meaning
OFF User Arm/Disarm Code not programmed
Flashing User Arm/Code is currently being programmed
Steady User Arm/Disarm Code has been programmed
TABLE 5 ZONE LED DEFINITION-USER PROGRAM MODE

11
been selected as an Exit/Entry Follower Zone,
Home/Away with Delay Zones, or 24 Hour Zone.
A8 + User 1 Code - User Program
Mode
A9 Keypad Sleep Mode ON/OFF
Enter this command to turn the keypad sounder
ON/OFF. When the keypad is in Sleep mode all
keypad sounds will be silenced except for key-
pad feedback beeps and Keypad Sounder on
Alarm.
User Commands - Optional
A0 Easy Exit
If enabled in Dealer programming, enter this
command while the panel is Armed to allow 3
minutes to exit the premises through Exit/Entry
and Exit/Entry Follower Zones.
A3 Access on PGM
If enabled in Dealer programming, enter this
command to activate the PGM output (Terminal
15) for 5 seconds.
Dealer Commands
A6 Download
(Programming Required)
Establish a connection between the PCD phone
line and the Control Panel phone line. When
ready, tell the installer to arm, then disarm.
Then enter A6 in order to establish a
connection. Phone connection to installer will
go "dead" as downloader and panel connect.
A7 Fault Find ON/OFF
Hardwired Zone Operation
Enter this command to turn Fault Find ON/OFF.
While in Fault Find mode, the loop response for
all zones will be set to the faster response of 40
ms. The keypad will beep for .25-seconds when
hardwired zones are faulted and for 1-second
when zones are restored.
Wireless Operation
(Signal Strength)
While in Fault Find mode the keypad will provide
an audible (Table 6) and visual (Figure 5) indi-
cation of each transmitter's signal strength. The
signal strength metering is based on a scale of 4
to 10, with 4 being marginal and 10 being excel-
lent.
The keypad will beep out a number, from 1-4,
corresponding to the signal strength of the trans-
mitter. See Table 6. Each beep is 1-second
long. The keypad will sound a short beep for
transmitters with signal strengths of 3 or less.
Signal Strength Logging Mode
The Signal Strength Logging Mode is a trouble-
shooting tool which allows the collection of sig-
nal strength information for all transmitters on
the system. Normally the Signal Strength of Su-
pervisory Signals are not logged; during Signal
Strength Logging Mode the signal strength infor-
mation for all supervisory signals received over
a two hour period will be saved to the LOG.
Local Activation
Enable [92-4=ON], this will initiate a two hour
test period where all supervisory signals will log
signal strength information.
Signal Strength = 8-10
Signal Strength = 6-7
Signal Strength = 4
Signal Strength = 5
1
1 2
1 2 3
1 2 3 4
FIGURE 5VISUAL SIGNAL STRENGTH INDICATION
TABLE 6 AUDIBLE SIGNAL STRENGTH INDICATION
SIGNAL STRENGTH KEYPAD SOUNDER
3 or less .25s BEEP
4 BEEP
5 BEEP BEEP
6-7 BEEP BEEP BEEP
8-10 BEEP BEEP BEEP BEEP

WI850D GEM-P800 Installation Instructions
12
Remote Activation
Using NAPCO's Quickloader Software
(Version 3.26 or higher), follow the instruc-
tions below:
From the Status Screen
Press F6
Select Miscellaneous Control
Select Enable Signal Strength Logging
Uploading Signal Strength Information
from the Log
After approximately (2) two hours, re-
establish a connection with the panel. Sig-
nal strength log information ranges from 1
to 10. The logging of signal strength should
appear similar to the sample LOG below:
Zone Features
[00] Exit/Entry Zones
Delay allows exit and entry through an Exit/
Entry Zone after the system is armed with-
out setting off an immediate alarm. Exit De-
lay allows the user to leave the premises
after arming. Entry Delay allows the user
time to enter and disarm. The entry delay
may be canceled by pressing F..
[01] Home/Away with Delay Zones
Zones that automatically bypass at the expi-
ration of the exit delay if the EXIT/ENTRY
zone(s) are not violated. Zones of this type
have a three (3) minute power-up delay,
and do not display or cause an alarm if
faulted when the system powers up. Press-
ing the Ckey cancels the 3 minute timer.
If Exit/Entry zone(s) are violated during the
exit delay, zones programmed as Home/
Away with Delay Zone(s) will have a fixed
20-second entry delay, if violated before the
Exit/Entry zone.
To eliminate this fixed 20-second entry de-
lay, also program zones as Exit/Entry Fol-
lower Zones [02].
To return protection to zones of this type,
press BC from the keypad or Mor
Nfrom a Keyfob. Program the Keyfob
AUX 1 or AUX 2 button for Full Set [81-7].
[02]Exit/Entry Follower Zones
Entry Delay allows the user time to enter and
disarm. Allows exit after the panel is armed
without setting off an immediate alarm and
allows entry only if an Exit/Entry Zone [00]
has been violated first. Zones of this type
have a three (3) minute power-up delay, and
do not display or cause an alarm if faulted
when the system powers up. Pressing the
Ckey cancels the 3 minute timer.
Group Bypassing - Zones programmed as
Exit/Entry Follower Zones will be Group by-
passed if the Ekey is pressed while dis-
armed or within the Exit Delay.
Auto Interior Bypassing - Also program
zones as Home/Away with Delay Zone(s)
[01] to automatically bypass at the expiration
of the exit delay if the EXIT/ENTRY Zone(s)
are not violated during the exit delay.
[03]Auto-Bypass Reentry Zones
Zones programmed as this zone type are
permitted to be faulted at the time of arming.
Once the zone is restored, while the control
panel is still armed, the zone will automati-
06/01/09 17:44 QL: Full Program Uploaded
06/01/09 17:42 QL: Technical Connection
(callback) Technician 2
06/01/09 15:23 Transmitter Status: GEM_SMK 1
(7A0DB5): SS=7
06/01/09 15:13 Transmitter Status: GEM_SMK 2
(768447): SS=8
06/01/09 15:13 Transmitter Status: Zone 2,
SS=6
06/01/09 14:27 Trouble: RF Link, GEM_RECV 1
06/01/09 14:25 Panic: Keypad
06/01/09 14:25 Panic: Keyfob 1(933780) SS=8
06/01/09 14:25 Dealer Program Mode Entered
06/01/09 14:24 Instant: Keyfob 1(933780)
SS=8
06/01/09 14:24 QL: Connection Terminated (10
MIN T/O)
06/01/09 13:13 QL: Full Program Downloaded
05/07/09 12:06 Open: User 2
05/07/09 12:06 Close: EasyArm
05/07/09 11:55 Trouble Restore: Low Battery,
GEM_SMK 2(768447) SS=8
05/07/09 10:21 Transmitter Status: GEM_SMK
(7A0DB5): SS=6
If A0 is Entered during Exit Time, Home/Away with
Delay Zones will be automatically bypassed, even if the
Exit/Entry Zone is violated. Easy Exit/Easy Arm [22-2] must
be enabled.
NOTE:

13
cally be unbypassed and any subsequent
violations of the zone will cause an alarm
condition.
[04] 24-Hour Protection
A zone that provides protection at all times,
whether or not the system is armed.
[05] 40 ms Loop Response
Normally loop response is 750 ms, select
this option to change the loop response to
40 ms. The slower the loop response, the
less sensitive the system will be to intermit-
tents (swingers). The programming option
is not permitted for UL installations.
[06] Open Circuit Zones
Program this zone type if unsupervised nor-
mally open circuit devices are required The
programming option is not permitted for UL
installations.
[07] Burg (Steady) Output
Enables the Bell Output on a zone trip for
each zone selected. The Bell Output will
remain ON for the length of time pro-
grammed for Burg (Steady) Output [07] or it
will remain ON until turned off by entering a
valid Arm/Disarm Code; 0 means output will
stay ON until reset.
[08] PGM Output
Enables the PGM Output on a zone trip for
each zone selected. The PGM Output will
remain ON until reset.
[09] Selective Bypass
If programmed, selected zones will be able
to be bypassed by the User. By default, all
zones are permitted to be bypassed.
System Times
[10] Exit Delay
The delay time which permits exit through
an Exit/Entry Zone [00] after the system is
armed, allows a user to leave the premises
without setting off an immediate alarm. Exit
Delay may be programmed for up to 255
seconds (4¼ minutes); a value of 0 defaults
to 60 seconds.
[11] Entry Delay
Delay time permits entry through Exit/Entry
Zone(s) after the system is armed without
setting off an immediate alarm. Entry Delay
allows the user time to enter and disarm the
system. Upon entering, the keypad sounder
will sound a steady tone (Entry Sound) to
remind the user to disarm the system. En-
try Delay Time [11] may be programmed for
up to 255 seconds (4¼ minutes); a value of
0 defaults to 30 seconds. Entry Delay may
be canceled by pressing Fbefore or
after arming.
[12] Burg (Steady) Output Time-out
Can be programmed from 1 to 255 min (4¼
hours); 0 means output will stay ON until
turned off by entering an Arm/Disarm Code.
[13] Fire (Pulsed) Output Time-out
Can be programmed from 1 to 255 min (4¼
hours); 0 means output will stay ON until
turned off by entering an Arm/Disarm Code.
[14] Test Timer Interval
Program the interval, in days, between Test
Timer reports. Test Timer Interval may be
programmed from 1 to 255 days.
[15] Line Cut Time-to-Fail
Enable this feature by programming the
delay time required to declare a line cut fail-
ure. Programming 000 will disable line cut
detection.
[16] Wireless Supervisory Timer
A transmitter will send a transmission every
time it is tripped; when there is no activity,
the transmitter sends a supervisory trans-
mission about once an hour. If the receiver
Normally Open Zone Wiring
Wire the normally
open contact
as shown (Zone 4).
EZ Zone Doubling™
resistor is required.
Program the
zone for
Open Circuit [06] operation.
3.9K
(Z)
ZONE 1
(E)
2.2K
ZONE 4
FIGURE 6OPEN CIRCUIT WIRING

WI850D GEM-P800 Installation Instructions
14
does not receive any signal (either a trip or a
status) from a transmitter in the time speci-
fied, a system trouble 'RF Supervisory Fail-
ure' will be indicated at the keypad. Timer is
programmable from 1-26 hours; 0 means
NO supervision. Note: Wireless Supervi-
sory Timer must be set to 10 hours.
[17] Wireless Smoke Supervisory Timer
A smoke detector will send a transmission
every time it is tripped; when there is NO
activity, the smoke detector sends a supervi-
sory transmission about once an hour. If the
receiver does not receive a signal (either a
trip or a status) from a transmitter in the time
specified, a system trouble 'RF Supervisory
Failure' will be indicated at the keypad. The
Supervisory timer is programmable from 1-8
hours; 0 means NO supervision.
[18] Test Timer Offset
Enter the time, in hours, that a Test Timer
will be reported after Dealer Mode has been
exited. With the default value of 12, the test
timer will be sent 12 hours after exiting
Dealer Mode. The test timer can also be
offset using NAPCO PCD3000 Downloading
Software. On power up the test timer is sent
immediately. Follow the commands below
to offset the test timer using Quickloader
Software:
From the Status Screen
Press q
Select Miscellaneous Control
Select Test Timer Offset
Enter
New Test Timer Offset: 12 hours
Enter uto advance the test timer due in
time by 12 hours.
System Features
[20] Keypad Features 1
(1) Enable Keypad Fire (7G)
Additional Programming required:
Select reporting to Telco 1 [36-1] or Telco 3
[56-1].
(2) Enable Keypad AUX (8G)
Additional Programming required:
Select reporting to Telco 1 [36-2] or Telco 3
[56-2].
(3) Enable Keypad Panic (9G)
Additional Programming required:
Select reporting to Telco 1 [36-3] or Telco 3
[56-3].
(4) Enable Ambush - If enabled, the 8th
User Code will send an Ambush report
when entered to disarm the system.
Additional Programming required:
Program User 8 Arm/Disarm Code.
Select reporting to Telco 1 [36-2] or Telco 3
[56-2].
UL Installations: If Keypad Fire [20-1] is
enabled, the keypad must be mounted
within (3) three feet from the Control Panel.
[21] Keypad Features 2
(1) Audible Panic - Keypad Panic will not
turn the Bell on unless this option is pro-
grammed.
(2) Exit/Entry with Urgency - select to
give an audible indication of Exit and Entry
times. During the last 10 seconds of entry
and exit time, the keypad sounds a distinct
sound to indicate the premises must be left
or the panel must be disarmed.
(3) Display Bypassed (Armed) - Select to
display bypassed zones while the panel is
armed.
(4) Disable Code Entry Beeps - Program
to disable keypad beeping on valid code and
function entries.
[22] Miscellaneous Features 1
(1) Abort Delay - Program to allow a 15
second Delay (except 24 Hour Zones) after
a zone trip before reporting. Disarm the
system within 15 seconds to prevent report-
ing.
(2) Easy Exit/Easy Arm- Enables
A0 command. While the system is
armed, entering this command allows 3 min-
utes to Exit through Exit/Entry and Exit/Entry
Follower Zones. Enabling this option also
enables Easy Arm, press the Dkey to arm
the system.
(3) Swinger Shutdown - Automatically
disables armed zones with excessive alarm/
restores (swingers). Non-24-Hour Protec-
tion zones: allows only 3 alarms and 2 re-
stores per zone per arming before the zone
is disabled.

15
(4) Bell on Line Cut (Armed) - Program to
turn the Bell Output on if the telephone line
has been cut while the panel is armed.
[23] Programmable Output Features 1
(1) Audio Verification - Program to acti-
vate the PGM during reporting. Select spe-
cific zones for audio verification by program-
ming the required zones in PGM Output
[08], PGM Features 2 [24] and PGM Fea-
tures 3 [25]. Connect the PGM to the
VeriphoneTM trigger low input.
(2) Access Output - Activates the PGM
output for 5 seconds using the A3
command.
(3) Follow Keypad Sounder - The follow-
ing keypad sounds will activate the PGM
output: Entry Sounder, Keypad Pulsing
Sounder, Keypad Output on Alarm, Chime,
Fault Find.
(4) Keyfob/Keyswitch Chirp - Program to
chirp the PGM Output (1) one time when the
panel is armed or (2) two times when the
panel is disarmed. Wire as shown in Figure 7.
[24] Programmable Output Features 2
(1) Fire - Program to activate the PGM on
a Fire alarm.
(2) AUX - Program to activate the PGM on
a AUX alarm.
(3) Panic - Program to activate the PGM
on a Panic alarm.
(4) Test Timer - Program to activate the
PGM during a Test Timer report.
[25] Programmable Output Features 3
(1) AC Fail - Program to activate the PGM
on the loss of AC. (15 minute delay)
(2) Low Battery - Program to activate the
PGM on a Low Battery condition.
(3) *Trouble - Program to activate the
PGM on a Trouble condition.
(4) Armed - Program to activate the PGM
when the panel is Armed. The PGM output
will flash when the panel has gone into
alarm.
*Includes Bell Cut, Fire Trouble, Receiver
Fail-to-Respond, Receiver Tamper, Re-
ceiver JAM, Wireless Smoke Low Battery,
Wireless Smoke Supervisory Fail.
[26] Miscellaneous Features 2
(1) Momentary Keyswitch Arming - Typi-
cally, connect a normally-open Keyswitch
across the zone AND its 3.3K zone-doubling
resistor.
(2) Reserved.
(3) Inhibit Fail-to-Communicate Dis-
play - This option prevents the keypad from
either indicating or sounding when a Fail to
Communicate has occurred.
(4) Inhibit Low Battery Display - Program
to inhibit the Low Battery Display at the key-
pad. Low Battery Reporting is not inhibited.
The programming option is not permitted for
UL installations.
Telephone Number 1 Programming
[30] Subscriber ID Number
For 4/2 format enter a 4 digit number. If 3/1
format is required, enter a 3 digit number,
then press the Fkey to blank the last
digit.
[31] Telephone Number 1
Program the phone number to be dialed for
Telephone Number 1. Program the number
directly, just as it is entered on a TouchTone
phone. A fixed Dial Tone Detection (E) is
included prior to the Dialing Prefix (Block
Number 44). Programming an E is not re-
quired for Telco 1, Telco 2 and Telco 3. If
dial tone detection is not desired select No
Dial Tone Detection in Communicator Fea-
tures [46-1].s Use the Fkey to blank out
remaining digits in the phone number.
[32] Receiver Format
Select the receiver format to be used to re-
port for Telephone Number 1: Program a 0
N/ON/CCOM
BLK
RED
+AUX
Siren Driver
Steady Input
PGM
+AUX
K1
FIGURE 7KEYFOB/KEYSWITCH CHIRP

WI850D GEM-P800 Installation Instructions
16
to disable reporting to Telco 1.
[0] Disabled [4] Universal High Speed
[1] Ademco Slow [5] Reserved
[2] Radionics Slow [6] Point ID
[3] Silent Knight Fast [7] Pager
[33] Receiver Options
(1) 2300 Hz HS / Kissoff - Select 2300 Hz
Handshake and Kissoff.
(2) Sumcheck - Only used for the follow-
ing Receiver Formats: Ademco Slow, Radi-
onics Fast, Silent Knight Fast and Universal
High Speed. This is a sophisticated data
format used to enhance the speed and
check the accuracy of the received trans-
mission. This format should be used when-
ever the central station has this capability.
Instead of sending a second round to verify
correct data, the panel sends a Sumcheck
digit after sending the Subscriber ID and
Alarm Code.
(3) Single Digit - 3/1 Format. 3-digit Sub-
scriber ID number and a 1-digit Alarm Code
will be transmitted.
(4) No Handshake - (All receiver formats
except Pager Format)
If programmed no Handshake / Kissoff is
required by the panel.
[34] Zone Report, Telco 1
Select zone(s) required to send an alarm
report to Telephone Number 1.
[35] Zone Restore Report, Telco 1
Select zone(s) required to send a restore
report to Telephone Number 1. The zones
will send a restore after Bell time-out, unless
programmed as silent zones.
[36] System Reporting, Telco 1
(1) Keypad Fire - Program to activate a
Keypad Fire report (7G).
(2) AUX/AMBUSH - Program to activate
an AUX or AMBUSH report (8G).
(3) Panic - Program to activate a Panic
report (9G).
(4) Test Timer - Program to activate a
Test Timer report.
[37] System Reporting, Telco 1
(1) AC Fail Report - Program to activate
an AC Fail report (15 minute fixed report
delay).
(2) Low Battery Report - Program to acti-
vate a Low Battery report.
(3) *Trouble Report - Program to activate
a Trouble report.
(4) Fire Report - Program to activate a
Fire report.
*Includes Bell Cut, Fire Trouble, Receiver
Fail-to-Respond, Receiver Tamper, Re-
ceiver JAM, Wireless Smoke Low Battery,
Wireless Smoke Supervisory Fail. Point ID
format will report trouble(s) by device and ID
number.
[38] System Restore Report, Telco 1
(1) AC Restore - Program to activate an
AC Restore report.
(2) Battery Restore - Program to activate
a Battery Restore report.
(3) Trouble Restore - Program to activate
a Trouble Restore report.
(4) Fire Restore - Program to activate a
Fire Restore report.
[39] Opening/Closing Report, Telco 1
Select users required to send opening and
closing reports to Telephone Number 1.
Do not program for users that are intended
to send an Opening After Alarm (Cancel
Code) or Conditional Closing reports.
Backup Telephone Programming
[40] Subscriber ID Number (Telco 2)
For 4/2 format enter a 4 digit number. If 3/1
format is required enter a 3 digit number
then press the Fkey.
[41] Telephone Number 2
Program the phone number to be dialed for
Telephone Number 2. A fixed dial tone de-
tection (E) is included prior to the Dialing
Prefix [44]. Dial tone detection can be dis-
abled by programming No Dial Tone Detec-
tion [46-1]. To program any additional delay
enter a "D" where required in the phone
number.

17
[42] Receiver Format (Telco 2)
Select the format that will be used to report
for Telco 2 (Backup reporting). Refer to
section [32].
[43] Receiver Options (Telco 2)
Refer to section [33] Receiver Options.
[44] Dialing Prefix
Dialing prefix for Telco 1, Telco 2, and Telco
3. Program if using an Outside access num-
ber.
[45] Communicator Features 1
(1) Communicator Enabled - Program to
enable the communicator.
(2) DTMF with Rotary Backup - The first
attempt to communicate is dialed using the
TouchTone method of dialing, subsequent
attempts are dialed using the pulse method
of dialing. Disable this feature to dial using
only rotary dialing.
(3) DTMF only - All attempts to communi-
cate dial using the TouchTone method of
dialing.
(4) Backup Reporting to Telco 2 - After 2
attempts are made to communicate to Telco
1 the backup phone number is dialed (Telco
2).
[46] Communicator Features 2
(1) No Dial Tone Detection - Program to
disable dial tone detection for Telco 1, Telco
2 and Telco 3.
(2) 2:1 Rotary Dialing - Changes the
make break ratio when rotary dialing from
1.5:1 to 2:1.
(3) Backup if < 4 attemps - If Backup
Reporting [45-4] has been enabled, the
communicator will use Telephone Number 2
[41] for the remaining retries when there are
less than 4 retries remaining.
(4) Reserved
Pager Programming
If Pager Format ([32]and/or[42]and/or[52] =
7) is selected, pager data will be displayed
as shown in Figure 8. If Pager Format is
selected 4/2 format must be programmed
and Sumcheck is not permitted. If a PIN
number is required refer to Leading Digits
[47].
Pager Alarm data is the same as 4/2 format
with the exception that the 2 digit Report
Code is transmitted before the 4 digit Sub-
scriber ID.
[47] Leading Digits
Pager PIN Number - If a PIN number is
required by the paging system, program the
PIN number in the Leading Digits location.
See sample program below.
If a 7-digit PIN number is required, program
the panel as follows:
[31]/[41]/[51] - Pager Telephone number
[32]/[42]/[52] - Select Pager Format
[47] - X X X X X X X C
Leading and Trailing digits can be letters B,
C or D. B = the * button on a telephone, C =
the # button on a telephone, D = 2 second
delay.
[48] Trailing Digits
Transmitted after alarm data. Refer to sec-
tion [47] for programming information.
[49] Pager Options
(1) Skip Alarm Data - Once pager format
is selected, program this option to skip
alarm data. If this option is selected, all the
programmed Leading and Trailing digits are
000 033-1234
Leading Digits
Report Code
Subscriber ID Number
FIGURE 8DEFAULT PAGER DISPLAY
7-digit PIN Number Terminating Digit (#)
Digits in Report Codes and subscriber IDs that are pro-
grammed with "B" through "F" will be converted to "0"s.
NOTE:

WI850D GEM-P800 Installation Instructions
18
sent, but the event code and subscriber ID
are not transmitted. With this option se-
lected, a telephone number programmed in
Leading Digits or Trailing Digits would send
the telephone number to the pager each
time a report is sent.
(2) Reserved
(3) Reserved
(4) Reserved
Telephone Number 3 Programming
[50] - [59]
Programming is the same as for Telco 1.
Program to split/double report to Telco 3.
Refer to sections [30] through [39].
Report Codes
[60] Zone Report Codes
Report Code for Zones 1 through 8.
4/2 format - The Zone Report Code is the
1st digit of the report code sent, the second
digit is the zone number of the reporting
zone. For example, if zone 2 has a report
code of 3, the report code would be 32.
3/1 format - Sends only the report Code
and does not append it with the zone num-
ber.
[61] Point ID Report Codes
Point ID Report Codes are defaulted to Bur-
glary for zones 1 through 8. Optionally,
Point ID codes for zones 1 through 8 can be
programmed as follows:
[1] Fire [7] Gas Alarm
[2] Panic [8] Heat Alarm
[3] Burglary [9] Reserved
[4] Holdup [A] Auxiliary
[5] General Alarm [B] 24 Hour
[6] Reserved
[62] Zone Codes
[62-1] Restore code - Zones 1 through 8.
The second digit of the restore code is the
zone number of the restored zone. For ex-
ample, if the Zone Restore Code [62] is pro-
grammed to E, the restore code for that
zone would be E4 (4/2 format).
[62-2] Trouble Code - Conditional Closing
Reports. Zones that are bypassed at the
time of arming send this code along with the
zone number of the bypassed zone(s). For
example a conditional closing by User 2,
with zones 2 and 3 bypassed would be as
follows:
1234 C2
F2
F3
[63] System Report Codes
Program a 2-digit report code for Keypad
Fire, Keypad AUX, Keypad Panic, Test
Timer, AC Fail, Low Battery, Trouble and
Fire.
[64] System Restore Code
The code sent when a system condition
restores. The second digit of the 2-digit
restore code is the second digit of the Sys-
tem Report Code [63]. For example, if a
Low Battery System Report Code is F8 the
Battery Restore would be E8 (4/2 format).
[65] Opening and Closing Codes
Program Opening and Closing Codes for
Users 1 through 8. The second digit of the
report code is the number of the user that
armed or disarmed the system. For exam-
ple, if the Closing Code [65] is programmed
with a C, the closing code for User 2 would
be C2 (4/2 format).
[66] Ambush Report Code
Program a 2-digit report code for Ambush.
To send an ambush report, program a User
Code for User 8, Program report User 8 as
Ambush [20-4] and Select reporting for
Telco 1 [36-2] and/or Telco 3 [56-2].

19
Enhanced Communicator Features
[67] Telephone Number 1
(1) Opening After Alarm (Cancel Code) -
When enabled, all users that are not se-
lected to report on Opening/Closing [39] will
report an Opening only when opening after
an alarm has occurred.
(2) Conditional Closing Telephone 1 -
When enabled, all users that are not se-
lected to report an Opening/Closing ([39],
[59]) will report a Closing only when zones
have been bypassed. The Zone Trouble
Code [62-2] is used to report zones that
have been bypassed at the time of the clos-
ing report.
(3) Reserved
(4) Reserved
[68] Telephone Number 3
(1) Opening after Alarm (Cancel Code) -
see [67-1].
(2) Conditional Closing Telco 3 - see
[67-1].
(3) Reserved
(4) Reserved
Wireless
Up to two receivers can be wired to the
GEM-P800. Each wireless transmitter can
be mapped to a zone. Only 1 wireless de-
vice is permitted per zone, however, the use
of both hardwired and wireless on a zone is
permitted.
To Map a transmitter to a zone:
1. Enter the Programming Block Number
that the transmitter is to be mapped to.
2. Enter the 7-digit RF ID number directly,
just as it is shown on the device label.
After the 7th digit is entered the keypad
will beep.
A transmitter will send a transmission every
time it is tripped. The transmitter also sends
a supervisory transmission about once
every hour. If the receiver does not receive
a signal from a transmitter in the time pro-
grammed in Wireless Supervisory Timer, a
system trouble 'RF Supervisory Failure' will
be indicated at the keypad.
Program Wireless Supervisory Timer [16] to
change the supervisory time from the default
of 12 hours.
The Signal strength of a transmitter can be
checked at the keypad (see A7
Fault Find Mode) or saved to the LOG (see
Signal Strength Logging Mode - pg. 11).
[71-78] Wireless Transmitters
Enter the RF ID# and the point number that
is to be mapped to the zone.
Programming Example
Map point 1 of a window door transmitter
with an RF ID# of 0012B0:0 to Zone 3.
1. Enter Dealer Mode.
2. Enter C(beeps) 73 (beeps)
3. Enter
012G200
4. Enter 1(beeps)
Note: If the RF ID# in step 3 is not entered
correctly the keypad will emit a 1 second
tone indicating incorrect entry. Repeat
steps 2 - 4 above.
[81] - [84] Wireless Keyfobs
The GEM-KF is a hand held wireless trans-
mitter capable of Arming and Disarming the
control panel and/or activating 2 Auxiliary
Functions. To activate the auxiliary func-
tions, press and hold the Mor Nkey for
1.5 seconds (see WI752 for more informa-
tion).
Enter the RF ID# and AUX 1 and AUX 2
options for each Keyfob.
AUX 1 & AUX 2
Programming Options:
1 Panic
Program a 1 in the AUX 1 and/or AUX 2
option to initiate a panic alarm when the M
or Nbuttons on the Keyfob are pressed.
Additional programming required:
Keypad Panic (9G) [20-3]
Panic Report to Telco 1[36-2] and/or Telco 3
[56-3].

WI850D GEM-P800 Installation Instructions
20
Audible Panic (Optional) [21-1]
2 AUX
Program a 2 in the AUX 1 and/or AUX 2
option to initiate a AUX alarm when the M
or Nbuttons on the Keyfob are pressed.
Additional programming required:
Keypad AUX (8G) [20-2]
AUX Report to Telco 1[36-2] and/or Telco 3
[56-2].
3 Bell ON
Program a 3 in the AUX 1 and/or AUX 2
option to turn the Bell ON when the Mor
Nbuttons on the Keyfob are pressed.
Press the Lbutton to turn the Bell OFF.
4 PGM
Program a 4 in the AUX 1 and/or AUX 2
option to activate the PGM Output when the
Mor Nbuttons on the Keyfob are
pressed. Press the Lbutton to turn the
PGM Output OFF.
5 Instant
Program a 5 in the AUX 1 and/or AUX 2
option to activate Instant Mode when the
Mor Nbuttons on the Keyfob are
pressed.
6 Access on PGM
Program a 6 in the AUX 1 and/or AUX 2
option to activate the PGM Output for 5 sec-
onds when the Mor Nbuttons on the
Keyfob are pressed.
Addition programming required:
Enable Access Output [23-2]
7 Full Set System
Program a 7 in the AUX 1 and/or AUX 2
option to Fully Set the System when the K
and the Mor Nbuttons on the Keyfob
are pressed, or when the Mor Nbut-
tons are pressed when the system is armed
with Exit/Entry Follower Zones or Home/
Away with Delay Zones that have been by-
passed.
8 Interior
Program an 8 in the AUX 1 and/or AUX 2
option to Bypass Exit/Entry Follower Zones
or Home/Away with Delay Zones when the
Mor Nbuttons on the Keyfob are
pressed (only if the system is programmed
exclusively for Home/Away with Delay
Zones).
[85] - [88] Wireless Smoke Detectors
Enter the RF ID# of the smoke detector.
A wireless smoke detector sends a supervi-
sory transmission about once every hour. If
the receiver does not receive a signal from a
transmitter in the time programmed in Wire-
less Smoke Supervisory Timer, a system
trouble 'RF Smoke Supervisory Failure' will
be indicated on the keypad.
Program Wireless Smoke Supervisory Timer
[17] to change the time from the default time
of 8 hours. Refer to Household Fire [96-3].
Note: Mark Smoke Detectors (Smoke 1
through Smoke 4) in order to identify them in
the event of a supervisory or battery failure.
If Household Fire [96-4] is selected, Wire-
less Smoke Supervisory Time is fixed at 4
hours.
Downloading
[90] Callback Telephone Number
Program the phone number of the
downloading computer to be dialed by the
panel during a high security download.
[91] Ring Count
Program the number of rings before the
panel will pickup. Ring Method [92-1]
(Downloading Features) must also be se-
lected.
[92] Downloading Features
(1) Ring Method - Enable the ring method
of downloading. The panel will pick-up on
the number of rings programmed in Ring