ProfiTap X2-3200G User manual

QUICK START GUIDE
X2-3200G
1CAREFULLY UNPACK ALL THE ITEMS AND RETAIN THE PACKAGING FOR LATER USE
X2-3200G is shipped with the following items:
X2-3200G main unit
2 x C13 AC power cord
1 x RJ45 female to 9-pin serial adapter
1 x rack mounting kit (front brackets, rear brackets, and the necessary screws)
4 x rubber foot with adhesive patch
X2-3200G is designed to be rack
mounted. Make sure the unit is
properly grounded and secured in
the rack using the included screws
and pre-mounted brackets.
X2-3200G
2
14 36 58 710 912 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31
E1 / 33 E2 / 34
2CONNECTING POWER & START UP
A
B
C
D
Power on the device by connecting the included AC power cord(s) to device and main power.
The unit starts up and boots once it is powered. You can follow its status by observing the activity LEDs [2].
Stage 2 (~2 secs): SYS, FAN, PS1/PS2 LEDs green, fans at normal speed
FAN, SYS: Green
PS1, PS2: Green if present and operational, yellow if absent or inoperational
Stage 1 (~35 secs): SYS LED yellow, PS1/PS2 LEDs green, FAN LED o, fans at full speed
BOOT SEQUENCE ~ SECS
NORMAL OPERATION MODE
20
19 22 21 24 23 26 25 28 27 30 29 32 31
[2]
[3]
[1]
X2-3200G features a serial management port, located on its front panel [1]. Connecting through this port allows the users to make the
initial setup on the device, configuring its network interface.
NOTE: If you are planning on using the device on a dynamic IP network, you can skip this step. The device will get an IP address
automatically and will be accessible via GUI or CLI with the default credentials:
User: admin
Password: Adminadmin1
3
INITIAL SETUP OVER SERIAL CONNECTION
Connect the X2-3200G serial administration port to a computer, using the supplied cable and adapters.
Use the following settings when connecting to the device: 115200 baud rate, 8 bit, no parity, 1 bit stop.
Login, using the following default credentials:
Default username: admin
Default password: Adminadmin1
Change network configuration using the .system.network.set command.
A
B
C
D

Connect the X2-3200G's Ethernet management port [3] to a network or computer, using an RJ45 Ethernet
cable. Keep in mind, in case you connect the unit directly to a computer, manual IP policy must be applied for
both the unit and the computer. Additionally, if the computer network interface is only 10/100M capable, a
twisted pair Ethernet cable must be used instead of a normal patch cable.
To access the X2-Manager interface, type h t t p s://< i p_addr> in your browser (Firefox or Chrome
recommended) with <ip_addr> being the unit’s static or DHCP provided IP.
On success, override any browser certificate alert to continue. X2-3200G prompts with its Status Page.
Login, using the default credentials (see: step 3C).
The main X2-Manager screen is displayed. For more information on X2-Manager, please refer to the User
Manual.
4
A
B
C
D
E
MANAGING X2-3200G USING X2-MANAGER
After the initial setup has been completed, or if the device is using a dynamic IP, the X2-Manager web interface can be accessed via the
device's Ethernet management port [3], either locally or over the network.
Provided the device is connected to a network or directly to a computer (see: step 4A), connect to X2-3200G
through SSH (default port 22), using its static or DHCP provided IP.
Login, using the default credentials (see: step 3C).
For more information on available CLI commands, please refer to the User Manual.
After the initial setup has been completed, or if the device is using a dynamic IP, the management CLI can be accessed via the device's
Ethernet management port [3], either locally or over the network.
5
MANAGING X2-3200G THROUGH CLI OVER SSH
A
B
C
Download the latest user manual from https://resources.profitap.com/
Profitap HQ B.V. — High Tech Campus 84 — 5656AG Eindhoven — The Netherlands
[e-mail] — [phone] — www.profitap.com
v1.7 — 03/22