Proflex Afx User manual

Colours may vary

AFX

Air Resistance Bike

User Manual

[Revision 3.0 May 2020]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE

AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may

vary in appearance, assembly, inclusions, specifications, description and packaging.

AFX Air Resistance Bike

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

•Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

•Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

•Keep clear of moving parts.

•Equipment may be a potential source of

electric shock or injury if misused.

•Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

•Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

•Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

•Work areas should be clean and well it.

•Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

•If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

•Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

•Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

•Do not use the equipment if tired or under

the influence of drugs, alcohol or

medication.

•This equipment is not intended for use by

persons with reduced physical, sensory or

mental capabilities.

General Fuel Safety

•Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

•Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

•Do NOT smoke near fuel or when

refuelling.

•Always shut off the engine before

refuelling.

•Do NOT refuel a hot engine.

•Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

•Always refuel in well ventilated areas.

•Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

•Use combustion engines OUTSIDE only,

and far away from windows, doors and

vents.

General Equipment Use and Care

•The equipment is designed for domestic

use only.

•Handle the equipment safely and carefully.

•Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

•Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

•Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

•Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

•Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

•Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases or liquids etc.

•The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

•Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

•For specific equipment safety use and care,

see Equipment Safety.

AFX Air Resistance Bike

General Electrical Safety

•Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

•Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

•When wiring electrically powered

equipment, follow all electrical and safety

codes.

•Wherever possible, use a residual current

device (RCD).

•High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

•Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

•Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

•Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

•Do NOT use electrical equipment in wet

conditions or in damp locations.

•Do NOT use electrical cords to lift, move or

carry equipment.

•Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

•The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

•Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

•Do NOT attempt any maintenance or repair

work not described in this manual.

•After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories or performing repair or

maintenance.

•Do NOT adjust while the equipment is

running.

•Perform service related activities in suitable

conditions, such as a workshop.

•Replace worn, damaged or missing

warning/safety labels immediately.

Air Resistance Bike Safety

Basic precautions should always be followed, including the following important safety instructions when using this equipment. Read all

instructions before using this equipment.

•Read all instructions and follow it carefully before using this equipment. Make sure the equipment is properly assembled and tightened before

use.

•Before exercise, in order to avoid injuring your muscles, warm-up exercises are recommended.

•Please make sure all parts are not damaged and fixed well before use. This equipment should be placed on a flat surface when using. Using a

mat or other covering material on the ground is recommended.

•Please wear proper clothes and shoes when using this equipment; do not wear clothes that might catch any part of the equipment.

•Do not attempt any maintenance or adjustments other than those described in this manual. Should any problems arise, discontinue use and

consult your local dealer.

•Be careful when step on or leave the pedal always hold the handlebars first. Make the pedal at your side at the lowest position, step on the pedal,

and stride over the main frame then step on the other pedal. When using, please hold the handlebar by hands, make the pedals running smoothly

by push or pull handlebars, then run the equipment regularly by cooperation of hands and feet. After exercise, please also make one pedal at

the lowest position and leave your foot on the higher pedal first and then another.

•Do not use the equipment outdoors. It is not a commercial model.

•This equipment is for household use only.

•Only one person at a time should use this equipment.

•If you feel any chest pains, nausea, dizziness, or short of breath, you should stop exercising immediately and consult your physician before

continuing.

•Care should be taken in mounting or dismounting the equipment.

•Do not allow children to use or play on the equipment. Keep children and pets away from the equipment while in use. This machine is designed

for adults use only. The minimum free space required for safe operation is not less than two meters.

WARNING: Before beginning any exercise program, consult your physician. This is especially important for people who are over 35 years

old or who have pre-existing health problems. Read all instructions before using any fitness equipment.

CAUTION: Read all instructions carefully before operating this product. Retain this User Manual for future reference.

AFX Air Resistance Bike

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

AFX Air Resistance Bike

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

AFX Air Resistance Bike

Table of Contents

Safety .............................................................................................................................................................2

Safety Symbols...........................................................................................................................................................4

Parts Identification .......................................................................................................................................7

Assembly.....................................................................................................................................................10

Adjustments ................................................................................................................................................18

Adjusting the Front Stabilizer End Cap.....................................................................................................................18

Adjusting the Tension Control Knob.........................................................................................................................18

Adjusting the Seat Height .........................................................................................................................................19

Specifications .............................................................................................................................................19

AFX Air Resistance Bike

Parts Identification

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

No. Description Qty No. Description Qty

1 Main Frame 1 40 Hexagon Flat Nut 7/8' 1

2 Rear Stabilizer 1 41 Stop Washer Ø35×2.0 1

3 Left Handrail 1 42 Puller Sleeve 7/8'' 1

4 Right Handrail 1 43 Ball Bearing Ø44.5 2

5 Seat Post 1 44 Bearing Bush Ø55.6×16 2

6 Left Connection Bar 1 45 Puller Sleeve 15/16'' 1

7 Right Connection Bar 1 46 Flat Washer Ø40×2.8 1

8 Front Stabilizer 1 47 End Cap for Rear Stabilizer 2

9 Belt 1 48 Decorative Cover 250×290×30 1

10 Fly Wheel 1 49 Crank 1

11 Hexagon Nut M10 2 50 Chain 1

12 Tension Spring 1 51 Chain Cover 1

13 Sensor with Wire 1 52 Left Nylon Nut 1/2” 1

14 Foam Grip Ø24×Ø35×280 2 53 Right Nylon Nut 1/2” 1

15 Fan Wheel Axle 1 54 Right Pedal 1

16 Hexagon Bolt M8×50 2 55 Wire Plug Ø12 6

17 Nylon Nut M8 7 56 Hexagon Bolt M5x15 5

18 End Cap for Front Stabilizer 1 57 Arc Washer Ø5×Ø14×1 5

19 Carriage Bolt M8x40 2 58 Seat Cushion 1

20 Arc Washer Ø8×Ø20×1.5 2 59 Cross Pan Head Tapping Screw ST3.9×16 5

21 Cap Nut M8×16 2 60 Decorative Cover158×23×58 1

22 Round End Cap Ø25×1.5 6 61 Flat Washer Ø8×Ø16×1.5 5

23 Nut Cap Ø24×13 2 62 Eye Bolt M6x36 2

24 Handlebar End Cap 2 63 Spacer Bush Ø21×Ø13×10 2

25 Flat Washer Ø8×Ø24×2 2 64 Flange Nut M10 2

26 Rotation Rod Ø16.0×261.5 1 65 Steel Bushing Ø18×Ø14×Ø8×10 2

27 Hexagon Nut M6 2 66 Cross Pan Head Self-Drilling Screw ST4.2×20 2

28 Meter 1 67 Cross Pan Head Bolt M5×10 7

29 Flat Washer Ø5×Ø9×0.8 2 68 Spring Washer Ø6 2

30 Cross Pan Head Screw M5×15 2 69 Spring Washer Ø8 4

31 Hand Pulse with Wire L=700mm 2 70 Screw M6x10 5

32 Hexagon Bolt M8×85 2 71 Left Flywheel Cover 1

33 Tension Control Knob 1 72 Circlip Ø10 2

34 Plastic Bushing Ø32×1.5 1 73 Right Flywheel Cover 1

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

No. Description Qty No. Description Qty

35 Seat Height Adjustment Knob M12 1 74 Nylon Nut M5 7

36 Left Pedal 1 75 Cross Pan Head Tapping Screw ST4.2x12 1

37 Clip 50×40×2.0 2 76 Meter Plate 1

38 Alien Bearing Ø31×Ø29×Ø 13×11 2 77 Bolt M5×25 1

39 Decorative Cover 350×130×47 1

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

Assembly

Step 1

Attach the Rear Stabilizer (2) onto the

rear curve of the Main Frame (1) with

four Hexagon Bolts (56) and four Arc

Washers (57).

Tighten bolts with S4 Allen Wrenches

provided.

Video Tutorial:

Assembly Guide

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

Step 2

Attach the Front Stabilizer (8) onto the

front curve of the Main Frame (1) with

two Cap Nuts (21), two Arc Washers

(20) and two Carriage Bolts (19).

Tighten nuts with Multi Hex Tool with

Phillips Screwdriver provided.

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

Step 3

Place the Rotation Rod (26) into the

hole of the Main Frame (1).

Install the Meter Plate (76) to the

Main Frame (1) with one Hexagon

Bolt (56) and one Arc Washer (57).

Tighten bolts with Allen Wrenches

provided.

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

Step 4

Slide the Left/Right Handrails (3)(4)

onto the Rotation Rod (26) and

secure in place with two Flat Washers

(25), two Spring Washers (69) and

two Nylon Nuts (17).

Tighten bolts with S6 Allen Wrenches

provided.

Then install two Nut Caps (23) onto

the Nylon Nuts (17).

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

Step 5

Install the Left/Right Connection Bar

(6)(7) to the Left/Right Handlebar

(3)(4) with two Hexagon Bolts (16),

two Flat Washers (61), two Spring

Washers (69) and two Nylon Nuts

(17).

Tighten nuts and bolts with Multi Hex

Tool with Phillips Screwdriver and

Allen Wrenches provided.

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

Step 6

Attach the Left Connection Bar (6)

and Left Pedal (36) to the crank with

one Spacer Bush (63), one Clip (37),

one Alien Bearing (38) and one Left

Nylon Nut (52) with clockwise

direction.

Tighten nuts with Multi Hex Tool with

Phillips Screwdriver provided.

Attach the Right Connection Bar (7)

and Right Pedal (54) to the crank with

one Spacer Bush (63), one Clip (37),

one Alien Bearing (38) and one Right

Nylon Nut (53) with counter-clockwise

direction.

Tighten nuts with Multi Hex Tool with

Phillips Screwdriver provided.

Note: Install the clip based on the sequence of images below:

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

Step 7

Attach the Seat Cushion (58) onto the

Seat Post (5) with three Flat Washers

(61) and three Nylon Nuts (17).

Tighten bolts with Multi Hex Tool with

Phillips Screwdriver provided.

Insert the Seat Post (5) into the Seat

Post Plastic Bushing on the tube of

the Main Frame (1), and then attach

the Seat Height Adjustment Knob (35)

onto the tube of the Main Frame (1)

by turning it in a clockwise direction to

lock the Seat Post (5) in the suitable

position.

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

Step 8

Slide the Meter (28) onto the Meter

Plate (76).

Then Connect the Sensor with wires

(13), Hand Pulse with Wire (31) and

Extension Sensor Wire (68) to the

wires that comes from the Meter (28).

Lock two Hexagon Bolts (32) to the

Main Frame (1).

Tighten bolts with the Allen Wrench

provided.

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

Adjustments

Adjusting the Front Stabilizer End Cap

Turn the front stabilizer end cap (18) on the front stabilizer as needed to level the air bike.

Adjusting the Tension Control Knob

•To increase the tension, turn the tension control knob (33) in a clockwise direction.

•To decrease the tension, turn the tension control knob (33) in an anti-clockwise direction.

NOTE: Resistance may lower over time. If this happens, simply adjust the tensioning bolt.

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

AFX Air Resistance Bike

Adjusting the Seat Height

Remove the seat height adjustment knob (35) from the tube of the main frame. Then slide the seat post up or

down slightly to the desired hole for the suitable position. Lock the seat post in place by tightening the seat

height adjustment knob (35) in a clockwise direction.

NOTE: When adjusting the height of the seat post, make sure the seat post plastic bushing does not exceed the

marked line on the seat post.

Specifications

Display functions Distance, Time, Speed, Calorie, Scan

Drive system Chain

Frame Steel

Pulse Sensors Yes

Note: Assembly Required

PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX PROFLEX

Some experts believe that the incorrect or prolonged use of almost any

product may cause serious injury or death. To help reduce your risk of

serious injury or death, refer to the information below. For more information,

see www.datastreamserver.com/safety

Consult all documentation, packaging

and product labelling before use. Note

that some products feature

documentation available online. It is

recommended to print and retain the

documentation.

Before each use, check the product for

loose/broken/damaged/missing parts,

wear or leaks (if applicable). Never use a

product with

loose/broken/damaged/missing parts,

wear or leaks.

Products must be inspected and serviced

(if applicable) by a qualified technician

every 6 months. This is based on

average residential use by persons of

average size and strength, and on a

property of average metropolitan size.

Use beyond these recommendations may

require more frequent

inspections/servicing.

Ensure that all users of the product have

completed a suitable industry recognised

training course before being allowed

access to the product.

The product has been supplied by a general merchandise

retailer that may not be familiar with your specific

application or description of application. Be sure to attain

third-party approval from a qualified specialist for your

application before use, regardless of any assurances from

the retailer or its representatives.

This product is not intended for use where fail-safe

operation is required. As with any product (for example,

automobile, computer, toaster), there is the possibility of

technical issues that may require the repair or

replacement of parts, or the product itself. If the possibility

of such failure and the associated time it may take to

rectify could in any way inconvenience the user, business

or employee, or financially affect the user, business or

employee, then the product is not suitable for your

requirements. This product is not intended for use where

incorrect operation or a failure of any kind, including but

not limited to, a condition requiring product return,

replacement, parts replacement or service by a technician

may cause financial loss, loss of employee time or an

inconvenience requiring compensation.

If this product has been purchased in error when

considering the information presented here, contact the

retailer directly for details of their returns policy, if

required.

diagrams or images may be reproduced or transmitted in any form or by any means, electronic or

mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,

without express permission or consent from the publisher.

Proflex AFX User manual

Popular Exercise Bike manuals by other brands