Create Room Cubby User manual

oh happy day
YOU’VE RECEIVED THE CREATE ROOM CUBBY!
[e-mail]
WWW.CREATEROOM.COM
USA / CANADA: 801-226-2686 (M-F 9AM-5PM MST)
UK/EU: [phone] OR [phone]
It’s already time for your first project. Let’s get to work!
To make the process simple and easy to follow, we’ve broken down the Cubby assembly
instructions into simple steps. All of the hardware you will need can be found in one bag.
If you have questions at any point of the assembly process, don’t hesitate to reach out to our
customer service team. They are the friendliest bunch of furniture experts and will be happy
to help you.
We are excited for you to enjoy your inspiring new workspace and can’t wait to see pictures!
Share your photos on Facebook and Instagram and don’t forget to tag @createroomco.
Happy crafting!
U0124
(Proprietary patented product and instructions. Do not copy or distribute.)

cubby
HARDWARE YOU’LL NEED:
TOOLS YOU’LL NEED:
Phillips Screwdriver
(not included)
A Friend
(not included)
Our furniture is designed to be
built with two people. Please
do not try to build alone.
Electric Drill with Phillips
ScrewDriver Extension
(not included)
x12
Cams
x8
Dowel
x12
Posts
x4
Connecting
Bolts
x6
25mm Euro
Screws
x4
Self Tapping
Screws
x1
Connecting
Plate
STACKING HARDWARE:
Note: if stacking you’ll need this hardware
from each of your 2 cubbies
SAFETY HARDWARE:
x2
Anchors
x2
Drywall
Screws
x2
Anchor
Screws
x2
Wall Screws
x1
Safety Wire
x12
Tote Tracks

12
34
The Create Room Cubby utilizes a cam and post locking system.
Please review these general instructions before you begin.
HOW TO
LOCK CAMS
AND POSTS:
Place Posts into panel until
plastic sleeve is touching wood.
Insert Cam with
arrow facing post.
Insert Post into Cam.
Gently turn Cam 220 degrees
clockwise to lock into position.
Do not overtighten.

1
1Start by assembling your hardware in the Side 1, Side 2 and Base panels. Locate
your posts and dowels and insert them into place by hand, as indicated below.
Side 1 Side 2
x8
Dowels
x2
Connecting
Bolts
Base
x12
Posts

2
Turn over your Base panel. With bottom side up, insert cams
by hand, as indicated below. Do not attempt to tighten.
2
x6
Cams
Base
(underneath)
3
Connect Side 1 and Side 2 with the Base, one at a time
by lining up the posts and dowels with the corresponding
holes and tapping firmly into place.
Base
Side 1
Side 2
Check that you are installing the
sides panels correctly by ensuring
that there is a smaller gap between
the peg holes and the bottom edge
than the peg holes and the top edge.
Once connected, use your screw driver to gently turn
cam 220 degrees clockwise to lock into position.

3
Turn your Cubby upright and insert one back panel at a time into the channels.
Side 1
Side 2
Back Panel
Back Panel
4

4
Side 1
Locate your Lid. With bottom side up, push posts and connceting bolts into place, as indicated below.
5
x6
Cams
x2
Connecting
Bolts
Connect the top piece to the left and
right panel by lining up the posts and
dowels with the corresponding holes
and tapping firmly into place.
Once connected, use your screw driver
to gently turn cams on Lid 220 degrees
clockwise to lock into position.
Back Panel
Side 2
Side 1
Base
Lid
Lid
(underneath)

5
Slide the divider into the Cubby beside the connector bolts, then gently push it intov place.
6
Use your screwdriver to tighten and lock the
connector bolts in place by turning clockwise.
Divider
Lid
Base
Side 2
Side 1
RAW EDGE
FINISHED EDGE

6
x8
Self Tapping
Screws
1
Use 25mm euro screws to fasten back panels.
7
x6
25mm Euro
Screws
Use 2 connecting plates found in each
of your Cubbies hardware and 8 self
tapping screws. Follow graphic below.
STACKING CUBBIES STEP (SKIP SECTION
IF NOT APPLICABLE):
x2
Connecting
Plate

7
2
DRYWALL ANCHOR INSTRUCTIONS:
1Attach Anchors using Anchor Screws.
Insert 2 Drywall Screws into pilot holes.
x2
Anchors
x2
Anchor Screws
SAFETY STEPS (RECOMMENDED):
x2
Drywall Screws

8
3
Open 1 Safety Wire and loop through the two connected anchors. Secure wire by locking into place.
Gently pull wire to ensure lock is secure.
Mount anchor to wall using 2 Wall Screws.
x2
Wall Screws
x1
Safety Wire
4

9
8Insert Tracks and Shelves. See next page for our recommended tote layout.
It can also be used as an organizational planogram.
x12
Tote Tracks

10

yipee!
YOU’VE DONE IT.
Now it’s time to fill up your new Cubby with all your crafting goodies.
Remember to share pictures of your crafts and craft space with us on Facebook
@CreateRoomFamily.
Proprietary, patented product and assembly instructions. Do not copy or distribute.