Projecta BLT500 User manual

BATTERY
ANALYSER
P/No. BLT500
MICROPROCESSOR CONTROLLED
12 VOLT
100-1700CCA

1. OVERVIEW
1. LED display
2 . Red positive(+) connection
3. Black negative (-) connection
4. Test result indicators
5. Directions buttons
6 . ENTER button
2. SETUP
2.1 Connect clips to battery
2.2 Battery voltage is displayed
2.3 Press ‘Enter’ to continue
3. BATTERY TEST
3.1 Select battery rating method
then press ‘Enter’
3.2 Take note of cold cranking
amp (CCA) rating from
battery label
3.3 If CCA rating is unknown,
use the following table
1
2
46
5
3
500A EN
1000 – 1299 cc
1300 – 1599 cc
1600 – 2000 cc
2000 – 2999 cc
3000 – 3500 cc
300 CCA
400 CCA
500 CCA
700 CCA
800 CCA
CCA
500A EN
1000 – 1299 cc
1300 – 1599 cc
1600 – 2000 cc
2000 – 2999 cc
3000 – 3500 cc
300 CCA
400 CCA
500 CCA
700 CCA
800 CCA
CCA
500A EN
1000 – 1299 cc
1300 – 1599 cc
1600 – 2000 cc
2000 – 2999 cc
3000 – 3500 cc
300 CCA
400 CCA
500 CCA
700 CCA
800 CCA
CCA

3.4 Enter battery CCA rating
then press ‘Enter’
3.5 Battery analysis will begin
3.6 After analysis results are
displayed
1. Good = Battery in
good condition
Bad = Replace
battery
2. Battery Cold
Cranking Amps
3. Remaining life of
battery, if below
45% then battery
should be replaced
3.7 Indicators will show
battery condition
1. Battery in good
condition
2. Battery condition
Is poor replace
battery
3. Battery charge is
low Recharge and
test again

Distributed by
AUSTRALIA
Brown & Watson International Pty Ltd
Knoxfield, Victoria 3180
Telephone [phone]
Facsimile [phone]
National Toll Free 1800 113 443
NEW ZEALAND
Narva New Zealand Ltd
22–24 Olive Road
PO Box 12556 Penrose
Auckland, New Zealand
Telephone [phone]
Facsimile [phone] IS358 Issue 1 1.11.16
WARRANTY STATEMENT
Brown & Watson International Pty. Ltd. (“BWI”) of 1500 Ferntree
Gully Road, Knoxfield, Vic., telephone [phone], fax
[phone], warrants that all products described in its current
catalogue will under normal use and service be free of failures in
material and workmanship for a period of one (1) year from the date
of the original purchase by the customer as marked on the invoice
(see elsewhere for specific warranty period). This warranty does
not cover ordinary wear and tear, abuse, alteration of products or
damage caused by the purchaser.
To make a warranty claim the consumer must deliver the product
at their cost to the original place of purchase or to any other place
which may be nominated by either BWI or the retailer from where
the product was bought in order that a warranty assessment may
be performed. The consumer must also deliver the original invoice
evidencing the date and place of purchase together with an
explanation in writing as to the nature of the claim.
In the event that the claim is determined to be for a minor failure
of the product then BWI reserves the right to repair or replace it at
its discretion. In the event that a major failure is determined the
consumer will be entitled to a replacement or a refund as well as
compensation for any other reasonably foreseeable loss or damage.
This warranty is in addition to any other rights or remedies that the
consumer may have under State or Federal legislation.
IMPORTANT NOTE
Our goods come with guarantees that cannot be excluded under
the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and compensation for any other
reasonably foreseeable loss or damage. You are also entitled to have
the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.