ProMariner ProNautic 2420P User manual

1
May 2013 14-900100-000
© Brunswick Bowling & Billiards Corp. 2013. All rights reserved.
Envoy Battery Charger
The Envoy battery charger is shown in Figure 1. A grounded power supply of 100-240VAC, 50/60 Hz
should be provided to the charger. Make sure that the battery charger is positioned so it has adequate
clearance to allow air circulation by the cooling fan. Detailed operating instructions are supplied with the
battery charger.
(1) COOLING VENT
(2) AMPERAGE OUT DISPLAY
(3) PERCENTAGE OF OUTPUTS USED
(4) FAULTS
(5) CHARGING PROFILE SELECTED
(6) AC AND DC CONNECTION COVER
(7) DC SIDE TERMINATIONS
(8) AC SIDE TERMINATIONS
(9) VOLTAGE OUT DISPLAY
(10) ABYC RECOMMENDED BONDING
STUD
The ProNautic 2420P charger is supplied with the proper 115/230VAC input power cord and 24VDC
output power cord already attached. The charger should also be preset for the type of battery included in
your Envoy lane machine. AGM should be preset to the AGM preset Prole #1 and the Lithium battery
should be preset to the LiFePO4 preset Prole #2. Call Brunswick Technical Service or your installing
distributor if your charger is not set to these proper settings for the type of battery in your Envoy.
It is best to install the charger onto a wall within 8’ of a power outlet that is not being used to power other
equipment. The AC power cord has an in-line On/Off power switch to allow you to turn the power off
BEFORE disconnecting or reconnecting the DC output cable from the LH charge port of the Envoy. The
DC output cable should then be reconnected to the LH charge port of the Envoy BEFORE turning the AC
power back on to the charger.
Figure 1

2
Battery Charger: Connecting to Envoy
Start with the AC input power to the battery charger switched OFF. Then connect the red 24VDC output
connector of the battery charger to the matching red charger connection port on the LH side cover of the
Envoy. Make sure that the Green ‘POWER’ LED on the LH side cover of the Envoy indicates that the
lane machine power is ON. Then switch ON the power to the battery charger. This sequence assures that
the charger always starts with the proper mode necessary for the state of battery discharge.
The Red ‘CHARGE’ LED located on the LH side cover of the Envoy, should turn ON only after it senses
voltage from a properly connected battery charger. This indicates the START of the battery charging
process. Switch OFF the power to the battery charger before removing the red charger connector from
the LH side cover of the Envoy. The Red ‘CHARGE’ LED does not turn off if the charger is disconnect-
ed. This Red ‘CHARGE’ LED remains ON until the lane machine prepares to run a lane or the Power is
turned off. The Red ‘CHARGE’ LED should then turn ON again after it senses voltage from a properly
connected battery charger. Refer to Figure 2.
(1) GREEN POWER LED MUST BE ON TO
CHARGE AND MONITOR BATTERIES
(2) CONNECT RED CHARGER CONNECTOR
TO PORT ON LEFT HAND SIDE COVER
(3) RED CHARGER LED TURNS ON TO
INDICATE START OF CHARGING
BATTERY
Figure 2
Remember, always connect battery charger to Envoy lane machine when not running lanes:
The Envoy green ‘POWER’ LED must be on to charge the batteries.
Connect the RED Charger Connection to the port on the LH cover BEFORE switching ON the
battery charger AC input power.
The Envoy red ‘CHARGE’ LED should turn ON only after it senses voltage from a properly con-
nected battery charger. This indicates the START of the battery charging process.
The battery charger is designed to remain connected to the lane machine whenever not running
the lane machine. It will keep the batteries in optimal condition and will not overcharge them.
Leaving the lane machine on for any extended time without connecting the battery charger will
slowly discharge the batteries and reduce their capacity.