Prorack K455 User manual

FittingKit
K455
GB
Fitting Instructions for Basic Carrier
x 4
x 4
1
Revision No:
1.3

FittingKit
K455
GB
MAX kg
MAX kg
W/P
WHD
W/P
WHD
Land Rover
Freelander 2, 5dr SUV 07-+
60
60
ZA
Freelander 2, 5dr SUV 07-+
60
60
US
Freelander 2, 5dr SUV 07-+
60
60
EU
Freelander 2, 5dr SUV 07-+
60
60
NZ
Freelander 2, 5dr SUV 07-+
60
60
AU
2

FittingKit
K455
GB
First Time Installation
Remove parts from packaging and check
contents. Contact your Prorack dealer if parts
are missing or damaged.
This kit fits type A, B, C and D.
These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3

FittingKit
K455
GB
Use keys to remove covers.
Use hex screwdriver to reverse adjusting
screw 10 turns.
Press adjusting screw and pull crossbar legs
out. Refer to the crossbar instructions for
crossbar adjustment.
Ensure each end of the crossbar is adjusted
equally.
4

FittingKit
K455
GB
Remove locking screw.
Apply protective strip as shown.
Trim if required.
A= Clamp
B= Roof line
C= Body rubber
D= Protective strip
Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
5

FittingKit
K455
GB
Refit locking screw so that it goes through
the hole in the clamp. Do not begin to tighten
the locking screw.
Fit rubber pad (supplied with crossbar) to foot.
Make sure the pad fits into the holes
underneath the foot.
6

FittingKit
K455
GB
Fitment
Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (unless otherwise stated).
Clamps over rubber door frame mouldings.
Please check the rear of this manual for
information relating specifically to your
vehicle.
Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
Tighten adjusting screw to 5 Nm.
7

FittingKit
K455
GB
Tighten locking screw on both legs evenly.
Final clamp position when tight.
Just touching point A
Pressure applied point B
Check crossbar is securely attached to the
vehicle.
8

FittingKit
K455
GB
Use keys to fit and lock covers
CAUTION:
Recheck all fasteners immediately after a load is
applied to the crossbars.
Regularly check screws are tight.
9

FittingKit
K455
GB
Maintenance
Clean the car roof and surfaces of the
product that will be in contact with the car
roof.
Follow the fitting instructions for fitting the
product to your vehicle. Make sure all steps
are carried out in order.
Set crossbars a minimum distance of 700mm
apart where no other distance is specified in
the fitting instructions. This is especially
important when carrying long loads.
Check unit is securely attached whenever
you refit it to the vehicle. If the unit feels
loose, refer to the fitting instructions and
readjust.
Some sunroofs and radio antennae cannot
be used when the product is fitted.
Do not modify this product.
Refer to the maximum permitted load
capacity specified in the fitting instructions.
Do not exceed the vehicle manufacturers
roof load rating if it is lower than the
maximum load capacity specified in the fitting
instructions.
Loads should not overhang the sides of the
product and be evenly distributed with the
lowest possible centre of gravity.
Long loads should be secured with non-
elastic straps to the front and rear of the
vehicle.
Objects with pointed ends (skis) should be
carried with the pointed ends to the rear of
the vehicle.
Remove all loose or removable objects from
the load prior to loading.
Make sure all loads are securely fastened
with non-elastic straps. Check regularly
during longer journeys.
10